Alcatel C350

Alcatel C350 manual

(1)
  • If not connected to the mains power or if there is a mains
    power failure, telephones that use cordless handsets will
    not work.
    You will then be unable to make or receive calls in the
    event of an emergency.
    This is why we recommend that you also keep a
    conventional telephone – one that doesn’t require a power
    supply – as a backup.
    Do not use your telephone to notify a gas leak when
    standing in the vicinity of the leak.
    It is recommended that you avoid using this device during
    electrical storms.
    Do not attempt to open the batteries, as they contain
    chemical substances. In the event of leakage, avoid contact
    with the skin, eyes, nose and mouth. In the event of
    contact, rinse the affected part for about twenty minutes
    with running water and seek urgent medical attention.
    Clean the product with absorbent paper or a dry cloth and
    contact your reseller for replacement batteries.
    13. ENVIRONMENT
    This symbol means that your inoperative
    electronic appliance must be collected separately
    and not mixed with the household waste.
    This appliance has been designed and
    manufactured with high quality materials and
    components that can be recycled and reused. Electrical and
    electronic appliances are liable to contain parts that are
    necessary in order for the system to work properly but
    which can become a health and environmental hazard if
    they are not handled or disposed of in the proper way.
    Consequently, please do not throw out your inoperative
    appliance with the household waste. You must deposit it at
    the appropriate local collection point or leave it with the
    vendor when buying a new appliance.
    Keen to preserve the environment, ATLINKS has equipped
    this appliance with a switching power supply, offering
    better energy efficiency. The advantages include not only
    very low electricity consumption, but also a more compact
    format than the conventional power supply units used by
    the previous range.
    The used batteries from your telephone (if it has batteries)
    must be disposed of in compliance with current
    environmental protection regulations. Comply with your
    local regulations. Return your batteries to your reseller or
    dispose of them at an approved recycling centre.
    Help us protect the environment in which we live!
    1. Press to access the call list. OR
    Press and to select CALL LIST.
    2. Press to select the desired entry.
    3. Press to view the caller’s number if applicable.
    6.2. Call from the Call List
    In idle mode:
    1. Follow step 1 and 2 in Section 6.1.
    2. Press or (only for C350) to dial out to the
    selected phonebook entry.
    7. PHONE SETTINGS
    7.1. Set the Ringer Melody for Internal/External
    Calls
    1. Press and to select HS SETTINGS.
    2. Press and to select RING SETUP.
    3. Press and to select INT RING or EXT
    RING.
    4. Press and to select the desired ringer
    melody from the melody list.
    Note: The respective ringer melody will be played while
    browsing the melody list.
    5. Press to confirm.
    7.2. Set the Ringer Volume
    1. Press and to select HS SETTINGS.
    2. Press and to select RING SETUP.
    3. Press and to select RING VOLUME.
    4. Press and to select the desired ringer
    volume (a total of 6 ringer volume levels including
    VOLUME OFF).
    5. Press to confirm.
    7.3. Store Direct Memory Access Number
    You can store three direct access numbers into digit KEY 1,
    KEY 2 and KEY 3, which will be convenient for you to dial to
    these numbers directly.
    1. Press and to select HS SETTINGS.
    2. Press and to select DIRECT MEM.
    3. Press and to select any one from KEY 1,
    KEY 2 and KEY 3.
    4. Press and then enter the number you would like to
    store, or edit the number existed before.
    5. Press to confirm.
    Note: Press and hold , or to call the stored number.
    8. Make an Internal Call (Duo/Trio versions)
    This feature is only applicable when there are at least two
    registered handsets.
    It allows you to make internal calls, transfer external calls
    from one handset to another handset and make conference
    calls. If the called handset is not answered within 60
    seconds, the called handset will stop ringing and the calling
    handset will return to standby mode.
    Note: If only one handset is registered to the base station,
    press will display “NOT POSSIBLE”.
    8.1. Intercom Another Handset
    1. In idle mode, press .
    2. Enter the desired handset number to intercom with.
    3. The called handset rings and press on the called
    handset to establish the internal call.
    Note: If only two handsets are registered to the base
    station, press will call another handset immediately.
    8.2. Call All Handsets
    1. In idle mode, press wand the registered handsets
    will display.
    2. press wto ring to all registered handsets.
    8.3. Transfer an External Call to another handset
    During an external call:
    1. Press and to select INTERCOM.
    2. Press to select the desired handset to intercom
    with.
    3. The external call is put on hold automatically and the
    called handset rings.
    4. Press on the called handset to establish an internal
    call.
    5. Press on the calling handset or put the calling
    handset on the charging cradle to end the current call
    with the external party.
    6. The external call is transferred to the called handset.
    8.4. Make a 3-way Conference Call
    The conference call feature allows one external call to be
    shared with two handsets (in intercom). The three parties
    can share the conversation and no network subscription is
    required.
    During an external call:
    1. Follow Steps 1 to 4 in section 8.3.
    2. Press and hold on the calling handset to establish
    the conference call.
    Note : Any handset hangs up during a conference call will
    leave the other handset still in connection with the external
    call.
    9. REGISTRATION
    Your handset and base station are pre-registered. Up to
    five handsets can be registered to a single base station.
    If you have broadband service,
    a micro-filter (not included) is required.
    3.3. Connecting the Charger(s)
    Plug the power adapter into mains socket.
    If you have a Broadband line
    If you connect your telephone to a line with a broadband
    connection, you will need to insert a micro-filter between
    the telephone and the telephone line, otherwise you may
    get interference between the telephone and the broadband,
    which could cause problems.
    In a home with broadband, every telephone must have a
    micro-filter connected, not just the one at the telephone
    point that your modem is connected to. If you need more
    broadband microfilters, contact your broadband supplier.
    4. USING YOUR PHONE
    4.1. Make a Call
    4.1.1. Preparatory Dialing
    Enter the phone number and press or (only for C350)
    to dial the number.
    Press to clear the entry.
    4.1.2. Direct Dialing
    Press or (only for C350) to take the line and enter
    the phone number.
    4.1.3. Dial from Direct Memory Keys
    In idle or off hook mode, press and hold / / to dial
    the direct memory number. You have to store number to
    the related key first. See section 7.3 for reference.
    4.1.4. Call from the Redial List
    Press (for C350) or (for C300) to access the redial
    list and press to select the desired redial number.
    Press or (only for C350) to dial out to the selected
    redial number.
    4.2. Handset Speakerphone (C350)
    During a call, you can press (only for C350) to
    alternate between handsfree and normal handset use.
    5. PRIVATE PHONEBOOK
    Your phone can store up to 50 private phonebook entries
    with names and numbers. Each phonebook entry can have
    a maximum of 20 digits for the phone number and 12
    characters for the name. You can also select different
    ringtones for your phonebook entries. Phonebook entries
    are stored alphabetically by name.
    5.1. Add a New Phonebook Entry
    In idle:
    1. Press to access the phonebook. OR
    Press and to select PHONEBOOK main
    menu item and then press to access the phonebook.
    2. Press to select ADD.
    3. Press to enter the name.
    4. Press to enter the number.
    5. Press and to select the desired ringtone for
    your phonebook entry.
    6. Press to store the phonebook entry.
    5.2. Call from the Phonebook
    In idle mode:
    1. Press to access the phonebook. OR
    Press and to select PHONEBOOK main
    menu item and then press to access the phonebook.
    2. Press or (only for C300) to dial out to the
    selected phonebook entry.
    6. CALLER DISPLAY (NETWORK DEPENDENT)
    This feature is available if you have subscribed the Caller
    Line Identification service with your telephone service
    provider. Your phone can store up to 20 received calls with
    date/time information in the Call List. The number will be
    shown on the LCD when the phone is ringing. If the number
    matches with one of the entries in your Private Phonebook,
    the caller’s name stored in the private phonebook will be
    displayed alternatively with the number. The handset will
    ring with the melody associated with that phonebook entry.
    If the caller number is disabled to send caller information,
    “WITHHELD” will display.
    If the caller number is not provided, “OUT OF AREA” will
    display.
    In standby, if three unanswered calls are received, “3 NEW
    CALLS” will be displayed.
    6.1. View the Call List
    All received calls are saved in Call List with the latest call
    putting at the top of the list. When the call list is full, the
    oldest call will be replaced by a new call. The unanswered
    call which has not been read is marked with a at the
    centre of the bottom line of the display.
    1. KNOWING YOUR PHONE
    1.1. Handset and Base Station Overview
    12. SEGURIDAD
    En el caso de que se produzca un riesgo eléctrico, el
    adaptador de alimentación funciona como dispositivo de
    aislamiento de alimentación de la corriente alterna. Por lo
    tanto, como precaución, debería instalarse cerca del
    electrodoméstico y con un fácil acceso.
    Para desconectar el dispositivo de la alimentación primaria,
    el adaptador de alimentación debe retirarse de la toma de
    la corriente alterna.
    En caso de que falle el adaptador de alimentación, debe
    sustituirse por un modelo idéntico.
    En caso de que el adaptador de alimentación no esté
    conectado o si hay una falla en la alimentación eléctrica, no
    funcionarán los teléfonos que usen auriculares
    inalámbricos. Por lo que usted será incapaz de hacer o
    recibir llamadas en caso de alguna emergencia.
    Ésta es la razón por la que recomendamos que disponga
    asimismo de un teléfono convencional – uno que no
    requiera alimentación eléctrica—como medida preventiva.
    ¡ No use el teléfono para avisar de una fuga de gas si
    se encuentra en las cercanías de dicha fuga!
    Se recomienda que evite usar este dispositivo durante
    tormentas eléctricas.
    No intente abrir la batería ya que contiene sustancias
    químicas.
    En caso de fuga, evite el contacto con la piel, ojos, nariz y
    boca. En caso de que se produzca el contacto, limpie bien
    la zona afectada durante unos veinte minutos con agua del
    grifo y busque atención médica urgente. Limpie el producto
    con un papel absorbente o un paño seco y póngase en
    contacto con su distribuidor para sustituir las baterías.
    13. MEDIO AMBIENTE
    Este símbolo indica que el electrodoméstico
    electrónico no operativo debe recogerse de forma
    separada y no mezclarse con los residuos
    domésticos.
    Este electrodoméstico ha sido diseñado y
    fabricado con materiales y componentes de gran calidad
    que pueden reciclarse y reutilizarse. Los electrodomésticos
    eléctricos y electrónicos pueden contener piezas que son
    necesarias para que el sistema funcione debidamente pero
    que pueden convertirse en un riesgo sanitario y
    medioambiental si no se manejan y se eliminan de forma
    adecuada. Por consiguiente, rogamos no tire el
    electrodoméstico inoperativo como si fuera un residuo
    doméstico.
    En caso de que sea el propietario del electrodoméstico,
    debe depositarlo en el punto apropiado local de recolección
    12. SAFETY
    In the event of an electrical hazard, the mains adapter acts
    as AC power isolating device. It should therefore, as a
    precaution, be installed close to the appliance and be easily
    accessible. To disconnect the device from the primary
    power source, the mains adapter must be removed from
    the AC socket.
    If the mains adapter fails, it must be replaced by an
    identical model.
    11. TROUBLESHOOTING
    If you have difficulty with your phone, please try the
    suggestions listed below.
    As a general rule, if a problem occurs, remove the batteries
    from all the handsets in your installation for about 1
    minute, then disconnect and reconnect the power supply to
    the base and reinstall the handset batteries.
    * Values may vary according to environment.
    ** Depending on initial battery charge.
    The store where you bought your telephone can also
    provide you with information and after-sales support.
    Problem Cause Solutions
    No dialing
    tone when
    pressing
    key
    a. The connection
    cord of the base
    station is not
    plugged in.
    b. The adapter cord
    is not plugged in
    correctly in the
    base station.
    c. The line is busy,
    as another
    handset is used.
    d. Wrong
    connection cord.
    a. Check the
    connections. Unplug
    and plug back in the
    mains. Check that
    the telephone line
    cord has been
    plugged into the
    base station and the
    phone socket.
    b. Check the base
    station plug and the
    AC plug (remove
    and plug-in).
    c. Wait until the line is
    unoccupied.
    d. Use the original
    connection cord.
    a. Base station out
    of range.
    b. Base station is
    not connected to
    mains.
    "OUT OF
    RANGE" is
    displayed.
    a. Reduce the range.
    b. Connect base
    station to mains.
    The call
    does not
    work.
    Service not
    activated
    or wrong operator.
    Check your
    Subscription with
    network.
    No display. Empty battery.
    Recharge battery.
    www.alcatel-home.com
    ATLINKS Europe
    147 avenue Paul Doumer
    92500 RUEIL-MALMAISON
    France
    © ATLINKS 2019 - Reprodución prohibida.
    El fabricante se reserva el derecho de modificar sin previo
    aviso las características de sus productos para introducir
    mejoras técnicas o cumplir con nuevas regulaciones
    oficiales. ALCATEL y ATLINKS son marcas registradas.
    Alcatel es una marca de Nokia, utilizada bajo licencia por
    ATLINKS.
    © ATLINKS 2019 - Reproduction prohibited.
    The Manufacturer reserves the right to modify the
    specifications of its products in order to make technical
    improvements or comply with new regulations.
    ALCATEL and ATLINKS are registered trademarks.
    Alcatel is a trademark of Nokia, used under license by
    ATLINKS.
    C300/C350 CH/LA
    A/W N.º: 10002179 Rev.0 (SP/EN)
    Printed in China
    o dejarlo con el distribuidor cuando adquiera uno nuevo.
    Deseoso de conservar el medio ambiente, ATLINKS ha
    equipado este electrodoméstico con un dispositivo de
    alimentación que ofrece una mayor eficiencia energética.
    Las ventajas incluyen no sólo un consumo muy bajo de
    energía, sino también un formato más compacto que las
    unidades de alimentación convencionales que se empleaban
    en la gama anterior.
    Las baterías usadas del teléfono (si dispone de las mismas)
    deben eliminarse según la normativa de protección
    medioambiental actual. Cumpla con la normativa local.
    Lleve a su distribuidor las baterías o deshágase de ellas en
    un centro de reciclaje aprobado.
    ¡Ayúdenos a proteger el medio ambiente en el que
    vivimos!
    ENGLISH
    1.
    In idle mode: Press to access the main menu
    In sub-menu mode: Press to confirm the selection
    During a call: Press to access Intercom/Phonebook/Re
    dial List/Call List
    2.
    In main menu mode: Press to go back to idle screen
    In sub-menu mode: Press to go back to previous level
    In sub-menu mode: Press and hold to go back to idle
    screen
    In editing / predialing mode: Press to clear a character
    / digit
    In editing / predialing mode: Press and hold to delete
    all the characters / digits
    During a call: Press to mute/unmute the microphone
    In idle mode: Press to intercom another handset
    In ringing: Press to suppress handset ringer
    3.
    In idle mode: Press to access the call list
    In menu mode: Press to scroll up the menu items
    In Phonebook list/Redial list/Call List: Press to scroll up
    the list
    During a call: Press to increase the volume
    In ringing: Press to increase the ringer volume
    4.
    In idle mode: Press to access the redial list (only for
    C350)
    In menu mode: Press to scroll down the menu items
    In Phonebook list/Redial list/Call List: Press to scroll
    down the list
    During a call: Press to decrease the volume
    In ringing: Press to decrease the ringer volume
    5.
    During a call: Press to end a call and go back to idle
    screen
    In menu/editing mode: Press to go back to previous
    menu
    In menu/editing mode: Press and hold to go back to
    idle screen
    In idle mode: Press and hold to power off the handset
    In idle mode: Press and hold to power on/off the
    handset
    6.
    In idle/predialing mode: Press to insert a flash
    During a call: Press to dial a flash
    7.
    In idle mode: Press to access the phonebook list
    8. (only for C300), (only for C350)
    For C350:
    During a call: Press to turn on/off the speakerphone
    In Idle mode/Predialing mode/Redial list/Call
    List/Phonebook entry: Press to make a call with
    speakerphone
    During ringing: Press to answer a call with speakerphone
    In idle mode: Press to access the redial list (for C300)
    9. ALPHANUMERIC KEYPAD, ,
    * key in idle mode: Press and hold to enable or disable
    the keypad lock
    # key in idle mode: Press and hold to turn on/off the
    ringer
    # key in call list mode: Press to review caller’s number
    if applicable
    0 key in predialing/number editing mode: Press and
    hold to insert a pause 1, 2, 3 key in idle/off hook
    mode: Press and hold to dial the stored direct memory
    number
    10.
    In idle/predialing mode: Press to make a call
    In Redial list/Call List/Phonebook entry: Press to make
    a call to the selected entry in the list
    During ringing: Press to answer a call
    11.
    Press on the base station to page your handset. It
    will ring for approximately 60 seconds.
    Press and hold the base station for about five
    seconds, the base station is entered into registration
    mode and allows handset registration.
    1.2. Display Icons and Symbols
    The LCD display gives you information on the current status
    of the telephone.
    Stable when the handset is in range of the base.
    Flashes when out of range of the base or not
    registered to the base.
    Stable when an intercom is in progress.Flash
    when there is an incoming internal call.
    Indicates a call is in progress.
    Indicates that handsfree is being used. (only for C350).
    Stable when an alarm is set.
    Flashes when the alarm time set before reaches.
    Indicates that the keypad is locked.
    Indicates when there are received new Voice Message
    Waiting (VMWI) not yet read.
    Disappears when all the voice messages have been
    read. (Network service dependent)
    Indicates that the ringer is switched off.
    Indicates when the battery is fully charged.Whole icon
    flashes when the battery performs initial charging.
    Internal block icon flashes when the battery is in final
    charging stage.
    Indicates when the battery needs charging. Flashes
    when low battery power level is detected.
    Indicates when more characters are existed before the
    text currently displayed.
    Indicates when more characters are existed after the
    text currently displayed.
    Indicates when new call is received.Turn off when new
    call has been read.
    Scroll up/down the menu items/Phonebook list/Redial
    list/Call List.
    2. PRECAUTIONS
    The signal quality will depend on the location and
    environment of the base and handset.
    Position your C300 / C350 away from sources of excessive
    heat (radiators, direct sunlight, etc.) and protect it from
    vibrationsand dust. Never allow your telephone to come
    into contact ter or other liquids, or with aerosols. To reduce
    the risk of interference and optimize reception, take
    particular care not to install the base in the immediate
    vicinity of windows, large metal objects, reinforced
    concrete, televisions, music centres, VCR or DVD players,
    halogen lamps or heating devices, fluorescent lighting,
    burglar alarms, microwave ovens, computers, etc.
    This telephone requires an electrical power supply in order
    to function.
    To clean your C300 / C350, use an antistatic cloth lightly
    moistened with water.
    3. INSTALLING YOUR PHONE
    3.1. Installing and Charging the Batteries
    1. Slide down to open the battery compartment cover.
    2. Place the 2 supplied AAA rechargeable batteries as
    indicated. Pay extra attention to direction of polarity.
    3. Slide the battery compartment cover back.
    4. Put the handset on the base and charge for 15 hours
    before using the handset for the first time. The
    handset will give a beep when it is properly placed on
    the base or charger.
    Notes:
    1. Use only the supplied NiMH rechargeable batteries.
    2. If the handset will not be used for a long time,
    disconnect and remove the batteries to prevent
    possible leakage.
    3.2. Connecting the Base Station
    1. Plug one end of the telephone line cord into the
    telephone jack on base bottom.
    2. Plug the small end of power adapter into a power jack
    on base bottom.
    3. Connect the power supply plug to the base jack.
    4. Plug the large end of power adapter into a wall power
    outlet.
    5. Plug the other end of the telephone line cord in to the
    telephone jack or micro-filter.
    6. Always use the cables provided in the box.
    If for some reason, the handset is not registered to the
    base station flashes (even when the handset is near
    the base station), register your handset according to the
    following procedure.
    1. Press and hold on the base station for about five
    seconds, the base station is entered into registration
    mode.
    2. Press and to select REGISTRATION.
    3. Press and and you are requested to enter
    the 4-digit system PIN (default PIN is 0000).
    4. Enter the 4-digit system PIN.
    5. Press to confirm.
    If the handset registration is successful, you will hear a
    confirmation tone and the will stop flashing. The
    handset will automatically be allocated the next available
    handset number.
    This handset number is shown in the handset display in
    standby mode. If the handset registration is unsuccessful,
    the will still flash.
    10. TECHNICAL DETAILS
    Free Field Range
    Up to 300 metres*
    Indoor Range Up to 50 metres*
    Handset Battery Life
    (average values)
    8 hours talk time**
    100 hours standby**
    Number of Handsets Up to 5
    Intercom Mode Yes
    Three-Way Conference
    (1 outside correspon-
    dent + 2 internal
    correspondents)
    Yes
    Electrical
    Connection/Base
    Mains Adaptor/Charger
    Only use the adaptors supplied
    with the telephone
    Caution: The network voltage is
    classified as a hazard by the
    criteria of this standard.
    Telephone Connection
    Appliance designed for
    connection to a TNV3 class
    (telecommunications network
    voltage) analogue telephone
    line.
    Batteries
    Only use the batteries supplied
    with the telephone.
    Use any other type of battery
    presents a risk of explosion.
    Used batteries must be disposed
    of in compliance with current
    environmental protection
    regulations.
    Operating Temperature From 5°C to 40°C
Alcatel C350

¿Necesita ayuda?

Número de preguntas: 1

¿Tiene alguna pregunta sobre Alcatel C350 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Alcatel C350 responder adecuadamente a su pregunta.

Ana , 2020-09-08 17:53:14 1 comentario

Como hago para reiniciarlo. Me suena ocupado cuando voy a llamar

Ana , 2020-09-08 17:54:41

Como hago. Pará reiniciarlo ya que cuando voy hacer una pregunta. No suena ocupado

Responde a esta pregunta

Vea el manual de Alcatel C350 aquí, de forma gratuita. Este manual pertenece a la categoría Teléfonos celulares y ha sido calificado por 1 personas con un promedio de 7.5. Este manual está disponible en los siguientes idiomas: Español, Inglés. ¿Tiene alguna pregunta sobre Alcatel C350 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Alcatel C350

General
Marca Alcatel
Modelo C350
Producto Teléfono celular
EAN 3700601420586
Idioma Español, Inglés
Tipo de archivo PDF
Desempeño
Tipo Teléfo✗ DECT
Contestador automático
Tipo de auricular Terminal inalámbrico
Tiempo de grabación 14min
Rango máximo en interiores 50m
Rango máximo en exteriores 300m
Tipo de timbre -
Número de melodías 10
Número de niveles del ajuste de volumen 8
Número de niveles de volumen del auricular 5
Diseño
Tipo de montaje Escritorio
Color del producto Negro
Teléfono Ancianos
Cantidad de botones 21
Características del teléfono
Altavoz
Capacidad de lista de direcciones 50entradas
Micrófono mudo
Función de paginación
Gestión de llamadas
Identificador de llamadas
Remarcado
Capacidad de lista de llamadas 10
Llamada en conferencia
Características de administración
Alarma
Control de volumen Botones
Exhibición
Pantalla incorporada
Pantalla LCD
Tamaño de la pantalla (HxV) 22 x 35mm
Monitor con luz de fondo
Color de luz de fondo Naranja
Puertos e Interfaces
Enchufe de entrada de CC
Control de energía
Tipo de batería AAA
Numero de baterías soportadas 2
Tecnología de batería Níquel-metal hidruro (NiMH)
Tiempo de conversación 8h
Tiempo de reposo 100h
Peso y dimensiones
Dimensiones de base 83.8 x 100.5 x 34.7mm
Dimensiones de auriculares (Ancho x Profundidad x Altura) 48.3 x 28 x 164.5mm
Contenido del embalaje
Número de teléfonos móviles incluidos 1
Estación base
Manual de usuario
Guía de configuración rápida
Auriculares incluidos
Indicación
Indicación de batería baja
Correo de voz indicación

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más