Anthro Fit Console Unit manual
RQuestions?1-800-325-3841AnthroCorporation Technology Furniture®10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.comSAVE THESE INSTRUCTIONS!Rev. F January 2006Hello! Thank you for choosing Anthro.Before beginning assembly of your Console Unit, take a moment to review the parts listed on the next pageto verify that your shipment is complete.Please review the assembly instructions of all Anthro products youpurchased and are planning to include in this installation, prior to beginning this assembly.Your Console Unit is heavy!A second person will be needed for this assembly procedure.To make the assembly of your Console Unit even easier, we have included all of the required tools. The handyHex Driver Bit can be used in your electric drill in place of the Hex Driver.Hex Driver5/32”............................................................375-5000-00Hex Driver Bit5/32”.....................................................375-5003-00Hex Key5/32”.................................................................375-5016-00Hex Key1/4”..................................................................375-5024-003-Way Wrench.............................................................225-5196-038 oz. Rubber Mallet.....................................................375-5022-00Console UnitAssembly Instructions1-800-325-3841Step 15Begin by placing the Base Tube Assembly(Locking Castersas shown)onto the Vertical Legs.Attach the Base Tubes to each Leg by inserting afi tBolt through a Tube Washer, then insert thefi tBoltthrough the Base Tube and carefully thread intoeach Vertical Leg.Tighten allfi tBolts and Cap Screws.Step 16(uses the1/8” Hex Key)Carefully rotate your Console Unit onto the Casters.Pop the six Small End Caps into the Leg ends.Congratulations!Your assembly is complete.(5/16-18 X 3.5”)fi tBolt325-5194-00fi tTube Washer225-2050-00 or 225-3522-00fi t Tube Washerfi t Tube WasherLocking CastersSmall End CapsAdjust the Caddy Shelf height by:1. Squeezing and holding the Paddle.2. Reposition the Caddy to the desired location.3. Release the Paddle.Rotate Knob toadjust Caddyangle.Squeeze Paddleto adjust Caddyheight.angle.Adjust the Caddy Shelf angle by:1. Rotating the Knob counterclockwise.2. Reposition the Caddy to the desired angle.3. Rotate the Knob clockwise.Adjusting your Console Caddy
¿Necesita ayuda?
Número de preguntas: 0¿Tiene alguna pregunta sobre Anthro Fit Console Unit o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Anthro Fit Console Unit responder adecuadamente a su pregunta.
Acerca de Anthro Fit Console Unit
+3
Vea el manual de Anthro Fit Console Unit aquí, de forma gratuita. Este manual pertenece a la categoría Oficinas y ha sido calificado por 1 personas con un promedio de 7.5. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Anthro Fit Console Unit o necesita ayuda? Haz tu pregunta aquí
Especificaciones de Anthro Fit Console Unit
Peso y dimensiones
| Dimensiones (Ancho x Profundidad x Altura) | 1930.39 x 1149.35 x 787.4 mm |
| Ancho | 1930.39 mm |
| Profundidad | 1149.35 mm |
| Altura | 787.4 mm |
Diseño
| Capacidad máxima de peso | 68 kg |
| Color del producto | Negro |
Ergonomía
| Levantar | 0 cm |
| Ángulo de inclinación | 0 ° |
| Ángulo de rotación | 360 ° |
| Interfaz de panel de montaje | No mm |
