BeamZ Prospero 152.936

BeamZ Prospero 152.936 manual

(1)
  • ENGLISH
    Congratulations to the purchase of this Beamz light effect. Please read this manual thoroughly prior to using the unit in
    order to benefit fully from all features.
    Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions
    to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical
    shock. Keep the manual for future reference.
    - Prior to using the unit, please ask advice from a
    specialist. When the unit is switched on for the first time,
    some smell may occur. This is normal and will disappear
    after a while.
    - The unit contains voltage carrying parts. Therefore do
    NOT open the housing.
    - Do not place metal objects or pour liquids into the unit
    This may cause electrical shock and malfunction.
    - Do not place the unit near heat sources such as
    radiators, etc. Do not place the unit on a vibrating
    surface. Do not cover the ventilation holes.
    - The unit is not suitable for continuous use.
    - Be careful with the mains lead and do not damage it. A
    faulty or damaged mains lead can cause electrical shock
    and malfunction.
    - When unplugging the unit from a mains outlet, always
    pull the plug, never the lead.
    - Do not plug or unplug the unit with wet hands.
    - If the plug and/or the mains lead are damaged, they
    need to be replaced by a qualified technician.
    - If the unit is damaged to such an extent that internal
    parts are visible, do NOT plug the unit into a mains outlet
    and DO NOT switch the unit on. Contact your dealer. Do
    NOT connect the unit to a rheostat or dimmer.
    - To avoid fire and shock hazard, do not expose the unit to
    rain and moisture.
    - All repairs should be carried out by a qualified technician
    only.
    - Connect the unit to an earthed mains outlet
    (220-240Vac/50Hz) protected by a 10-16A fuse.
    - During a thunderstorm or if the unit will not be used for a
    longer period of time, unplug it from the mains. The rule
    is: Unplug it from the mains when not in use.
    - If the unit has not been used for a longer period of time,
    condensation may occur. Let the unit reach room
    temperature before you switch it on. Never use the unit
    in humid rooms or outdoors.
    - During operation, the housing becomes very hot. Do not
    touch it during operation and immediately after.
    - To prevent accidents in companies, you must follow the
    applicable guide lines and follow the instructions.
    - Secure the unit with an extra safety chain if the unit is
    ceiling mount. Use a truss system with clamps. Make
    sure nobody stands in the mounting area. Mount the
    effect at least 50cm away from inflammable material and
    leave at least 1 meter space on every side to ensure
    sufficient cooling.
    - This unit contains high intensity LEDs. Do not look into
    the LED light to prevent damage to your eyes.
    - Do not repeatedly switch the fixture on and off. This
    shortens the life time.
    - Keep the unit out of the reach of children. Do not leave
    the unit unattended.
    - Do not use cleaning sprays to clean switches. The
    residues of these sprays cause deposits of dust and
    grease. In case of malfunction, always seek advice from
    a specialist.
    - Only operate the unit with clean hands.
    - Do not force the controls.
    - If the unit has fallen, always have it checked by a
    qualified technician before you switch the unit on again.
    - Do not use chemicals to clean the unit. They damage the
    varnish. Only clean the unit with a dry cloth.
    - Keep away from electronic equipment that may cause
    interference.
    - Only use original spares for repairs, otherwise serious
    damage and/or dangerous radiation may occur.
    - Switch the unit off prior to unplugging it from the mains
    and/or other equipment. Unplug all leads and cables
    prior to moving the unit.
    - Make sure that the mains lead cannot be damaged when
    people walk on it. Check the mains lead before every
    use for damages and faults!
    - The mains voltage is 220-240Vac/50Hz. Check if power
    outlet match. If you travel, make sure that the mains
    voltage of the country is suitable for this unit.
    - Keep the original packing material so that you can
    transport the unit in safe conditions
    This mark attracts the attention of the user to high voltages that are present inside the housing and that are of
    sufficient magnitude to cause a shock hazard.
    This mark attracts the attention of the user to important instructions that are contained in the manual and that he
    should read and adhere to.
    DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic
    attacks should be aware of the effects that this light effect may have on them.
    The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate
    and their guarantee!
    NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature betweenC/41°F
    and 35°C/95°F.

¿Necesita ayuda?

Numero de preguntas: 0

¿Tiene alguna pregunta sobre BeamZ Prospero 152.936 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de BeamZ Prospero 152.936 responder adecuadamente a su pregunta.

Vea el manual de BeamZ Prospero 152.936 aquí, de forma gratuita. Este manual pertenece a la categoría Máquinas de efectos y ha sido calificado por 1 personas con un promedio de 7.3. Este manual está disponible en los siguientes idiomas: Español, Holandés, Inglés, Alemán. ¿Tiene alguna pregunta sobre BeamZ Prospero 152.936 o necesita ayuda?

Especificaciones de BeamZ Prospero 152.936

Marca BeamZ
Modelo Prospero 152.936
Producto máquina de Efectos
EAN 8715693267730
Idioma Español, Holandés, Inglés, Alemán
Tipo de archivo PDF
Lámparas
Color de luz Azul
Diseño
Color del producto Negro
Control de energía
Fuente de energía Corriente alterna
Voltaje de entrada 220 - 240V
Frecuencia de entrada 50Hz
Peso y dimensiones
diámetro de la bola -
Ancho 155mm
Profundidad 200mm
Altura 145mm
Peso 1500g
Características
Cantidad de canales DMX 8canales
Puertos e Interfaces
Entrada XLR
Salida XLR 1

Productos relacionados BeamZ Prospero 152.936

    Manuales de productos relacionados

    máquina de Efectos BeamZ

    Añadir manual

    ¿Tiene un manual que le gustaría añadir?