Cateye Fit CC-PD100W

Cateye Fit CC-PD100W manual

(1)
  • Measure wheel circumference (L) of your bike
    To get the most accurate
    calibration do a wheel roll out.
    With the valve stem perpen-
    dicular to the ground, mark
    the pavement at the valve
    stem. With the riders weight
    on the bike, roll the wheel one tire revolution
    in a straight line and mark the ground when
    the valve stem is perpendicular to the ground
    again. Measure the distance in millimeters. This
    is the most accurate wheel calibration number.
    Before using the computer, please thoroughly read this manual and keep it for future
    reference.
    Our website shows how to install and set up the unit on your bicycle, in an understandable way
    using a movie (http://www.cateye.com).
    Installation conditions
    The back of the com-
    puter must face the
    speed sensor.
    1
    Removing the insulation sheet
    Remove the battery case cover, and hold
    the battery holder tab to pull out the battery.
    The battery holder is lifted when either tab
    is pulled up. Remove the insulation sheet
    under the battery.
    If the battery is detached, insert it cor-*
    rectly. (
    Replacing the battery)
    Insert the battery holder with the *
    mark
    toward the front side of the computer.
    2
    Press the AC button while press-
    ing and holding the MENU button
    (formatting operation)
    Check that the
    whole screen illu-
    mination is turned
    on for 5 seconds.
    Press and hold the * MENU button for 3
    seconds after you release the AC button.
    3
    Select the measurement unit
    (Speed, Stride, and Weight)
    When the
    1.
    MODE button is
    pressed, KM. CM. KG
    and MILE. INCH. LB
    will ash alternatively for
    selection.
    With the desired measurement unit dis-2.
    played, press the MENU button.
    4
    Set the date
    When the 1. MODE button
    is pressed, YY/MM/DD
    (Year, Month, Day) will
    flash in different order
    for selection.
    When the
    2.
    MODE button is
    pressed and held, the item to set will appear
    for selection, and “11” (Year) will fl ash.
    Press the 3. MODE button to increase the
    ashing value, whereas press and hold it
    to switch the item to set. Set “Month” and
    “Day” in the same procedure.
    Press the
    4. MENU button to proceed to “Set
    the clock”.
    When it fails to set the date, “* ERROR” will appear.
    5
    Set the clock
    Set the display format of
    12H” or 24H”, and the
    values for “Hour and
    “Minute” in the same
    procedure as Step 4.
    Press the MENU button
    to proceed to “Enter the
    tire circumference”.
    For the display format of * 12H”, select
    AM” (morning) or “PM” (afternoon).
    6
    Enter the tire circumference
    Enter the tire circumference of your
    bicycle (distance per turn) in mm.
    (
    Tire circumference reference table)
    Press the
    1. MODE but-
    ton to adjust the value,
    and press and hold it to
    move to the next digit.
    Enter the value for “ones
    place digit” through “thousands place digit”
    in the same procedure.
    Press the 2. MENU button to proceed to “Enter
    the weight”.
    When any invalid value is entered, *
    ERROR” will appear.
    7
    Enter the weight
    Enter your weight in the
    unit you selected in Step
    3 (KG or LB).
    Set the value in the same
    procedure as Step 6.
    Press the MENU button to proceed to
    “Enter the stride”.
    8
    Enter the stride
    Enter your stride in the
    unit you selected (CM
    or INCH). (
    How to
    measure the stride)
    Set the value in the
    same procedure as Step 6.
    Press the MENU button to confi rm the setting.
    Now, preparing the computer is completed.
    AC
    MENU
    SENSOR ZONE
    SENSOR ZONE
    SENSOR ZONE
    SENSOR ZONE
    5 mm5 mm
    Nylon ties (x2)
    Sensor zone
    Speed sensor
    Speed sensor
    Sensor zone
    Magnet
    Magnet
    Max
    70 cm
    YES!
    Pull
    securely
    Nylon ties
    To the sensor zone
    When attaching the bracket to the handlebar
    Install the bracket and computer
    Package contents
    Remove/install the computer
    Install the speed sensor Install the magnet
    For receiving sensitivity reasons, attach the bracket so that the back of the computer faces the speed sensor.*
    Use the applicable optional parts when attaching to an aero-shaped handlebar or a large stem.*
    Click
    While supporting it by hand,
    push it out as if lifting the
    front up.
    Install it fi rmly in place
    until it clicks.
    Cut
    CAUTION:
    Round off the cut edge
    of the bracket band to
    prevent injury.
    ETRTO Tire size
    L (mm)
    47-203 12x1.75 935
    54-203 12x1.95 940
    40-254 14x1.50 1020
    47-254 14x1.75 1055
    40-305 16x1.50 1185
    47-305 16x1.75 1195
    54-305 16x2.00 1245
    28-349 16x1-1/8 1290
    37-349 16x1-3/8 1300
    32-369 17x1-1/4 (369) 1340
    40-355 18x1.50 1340
    47-355 18x1.75 1350
    32-406 20x1.25 1450
    35-406 20x1.35 1460
    40-406 20x1.50 1490
    47-406 20x1.75 1515
    50-406 20x1.95 1565
    28-451 20x1-1/8 1545
    37-451 20x1-3/8 1615
    37-501 22x1-3/8 1770
    40-501 22x1-1/2 1785
    47-507 24x1.75 1890
    50-507 24x2.00 1925
    54-507 24x2.125 1965
    25-520 24x1(520) 1753
    24x3/4 Tubuler 1785
    28-540 24x1-1/8 1795
    32-540 24x1-1/4 1905
    25-559 26x1(559) 1913
    32-559 26x1.25 1950
    37-559 26x1.40 2005
    40-559 26x1.50 2010
    47-559 26x1.75 2023
    50-559 26x1.95 2050
    54-559 26x2.10 2068
    Preparing the computer
    Element names
    How to install the unit on your bicycle
    Stem
    Bracket
    Bracket
    Speed sensor
    Sensor rubber pad
    Bracket rubber pad
    Bracket rubber pad
    Remove
    backing
    Remove
    backing
    Bracket band
    Bracket band Handlebar
    Dial
    Right front fork
    Spoke
    Magnet
    SENSOR ZONE
    Display format
    Clock display
    Hour/Minute
    YY/MM/DD
    Bracket band
    Bracket
    Dial
    Speed sensor
    Magnet
    Bracket rubber pad Sensor rubber pad
    AC
    MODE
    MODE
    MENU
    Dot section
    Battery
    case
    cover
    The clearance between the speed sensor
    and magnet is 5 mm or less.
    After installing the speed sensor, check that the speed is displayed on the computer by turn-
    ing the front wheel with the computer installed to the bracket. If not displayed, review the
    installation conditions, and check the positions of the speed sensor and magnet.
    CAUTION:
    The computer in the bike mode measures speed only when installed on the bracket.
    NO!
    This unit can be used for measuring speed and distance while installed on your bicycle, and also used
    as a pedometer for measuring calorie consumption and number of steps in everyday life while carried
    with you all the time. First of all, go through “Preparing the computer” and “How to install the unit on
    your bicycle”.
    Tire circumference reference table
    Generally, the tire size is indicated on the *
    side of the tire.
    ETRTO Tire size
    L (mm)
    57-559 26x2.125 2070
    58-559 26x2.35 2083
    75-559 26x3.00 2170
    28-590 26x1-1/8 1970
    37-590 26x1-3/8 2068
    37-584 26x1-1/2 2100
    650C Tubuler
    26x7/8
    1920
    20-571 650x20C 1938
    23-571 650x23C 1944
    25-571
    650x25C
    26x1(571)
    1952
    40-590 650x38A 2125
    40-584 650x38B 2105
    25-630 27x1(630) 2145
    28-630 27x1-1/8 2155
    32-630 27x1-1/4 2161
    37-630 27x1-3/8 2169
    18-622 700x18C 2070
    19-622 700x19C 2080
    20-622 700x20C 2086
    23-622 700x23C 2096
    25-622 700x25C 2105
    28-622 700x28C 2136
    30-622 700x30C 2146
    32-622 700x32C 2155
    700C Tubuler 2130
    35-622 700x35C 2168
    38-622 700x38C 2180
    40-622 700x40C 2200
    42-622 700x42C 2224
    44-622 700x44C 2235
    45-622 700x45C 2242
    47-622 700x47C 2268
    54-622 29x2.1 2288
    60-622 29x2.3 2326
    L mm
    When attaching the bracket to the stem
    Install the speed sensor and magnet
    How to measure the stride
    The stride means the distance between
    adjacent tiptoes of your footprint. Mark at
    your tiptoe in the start point and the point
    after you make 10 steps, and then measure
    the distance between them.
    The stride becomes larger as you walk faster. *
    For measurement, walk at a normal speed.
    An average stride is determined by dividing the
    walking distance by 10 (number of steps).
    Walking distance
    A
    /
    10 (Number of steps) = Stride
    13
    210
    A
    Installation conditions
    The distance from the speed sensor to the
    computer must be less than 70 cm.
    The magnet must pass through the sensor
    zone of the speed sensor.
    ACAC
    Click
    When the computer
    is mounted on the
    bracket
    Battery holder
    Insulation sheet
    This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-
    tions:(1)This device may not cause harmful interference, and (2) this device must accept any interfer-
    ence received, including interference that may cause undesired operation.
    Modifi cations The FCC requires the user to be notifi ed that any changes or modifi cations made to this device
    that are not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate the equipment.
    Perform the formatting operation according to the following procedure when you use the unit for the fi rst time or restore the unit to the setting at the time of factory shipment.
    CATEYE FIT
    CC-PD100W ENG
Cateye Fit CC-PD100W

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Cateye Fit CC-PD100W o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Cateye Fit CC-PD100W responder adecuadamente a su pregunta.

Vea el manual de Cateye Fit CC-PD100W aquí, de forma gratuita. Este manual pertenece a la categoría Ordenadores de bicicleta y ha sido calificado por 1 personas con un promedio de 7. Este manual está disponible en los siguientes idiomas: Inglés. ¿Tiene alguna pregunta sobre Cateye Fit CC-PD100W o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Cateye Fit CC-PD100W

General
Marca Cateye
Modelo Fit CC-PD100W
Producto Ordenador de bicicleta
EAN 4990173022922
Idioma Inglés
Tipo de archivo PDF

Preguntas frecuentes

A continuación, encontrarás las preguntas más frecuentes sobre el Cateye Fit CC-PD100W .

¿Tu pregunta no está en la lista? Haz tu pregunta aquí

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más