Epson LabelWorks LW-400

Epson LabelWorks LW-400 manual

(1)
  • Read this document carefully to use this product safely
    and correctly.
    Safety Instructions
    For your safety, read the attached documents carefully
    to use this product correctly. After you have read all
    instructions, keep this manual handy for future reference
    and to make your concerns clear.
    Items below indicate safety precautions to protect users,
    their surroundings and their property from possible
    injury or damage.
    Precautionary notations are categorised as follows
    according to personal injury and damage to the
    equipment if the instructions are ignored or the
    equipment is misused.
    DANGER
    This symbol indicates information that, if ignored, could
    possibly result in serious or fatal personal injury. Take
    extra caution in performing procedures with DANGER
    headings.
    WARNING
    This symbol indicates information that, if ignored, could
    possibly result in serious personal injury or even death
    due to incorrect handling.
    CAUTION
    This symbol indicates information that, if ignored, could
    possibly result in personal injury or physical damage due
    to incorrect handling.
    The following describes the meaning of each symbol used in the
    precautions.
    This indicates an important reminder.
    This indicates a prohibited item.
    This indicates a mandatory procedure.
    DANGER
    When handling batteries
    If liquid leaking from an alkaline battery gets into your
    eyes, do not rub your eyes but immediately wash them
    well with clean water and contact a doctor. Otherwise, it
    may cause blindness.
    Users Guide
    English
    WARNING
    When using the AC adapter and power cable
    Do not use any AC adapter or power cable other than the
    dedicated AC adapter and power cable. Do not use the
    AC adapter with other than the specified voltage also.
    Otherwise, damage, overheating, fire or electric shock
    may occur.
    Take the following precautions when handling the AC
    adapter and power cable.
    Make sure to avoid octopus wiring.
    Make sure the plug is not dusty before inserting it into
    an outlet.
    Insert the plug firmly into the outlet.
    Do not hold the plug with wet hands.
    Do not pull the power cable when disconnecting
    the plug. Be sure to hold the plug when disconnecting it.
    Do not make any modification to the AC adapter or
    power cable.
    Do not apply strong shocks to or put a heavy object on
    the AC adapter or power cable.
    Do not bend or twist the AC adapter or power cable
    forcibly.
    Do not place the AC adapter or power cable near a heater.
    Do not use any damaged AC adapter or power cable.
    Otherwise, damage, overheating or smoking may occur,
    which may result in fire or electric shock.
    Do not touch the plug during thunderstorms.
    When handling batteries
    Keep batteries out of reach of children. They are
    extremely dangerous if swallowed. Contact a doctor
    immediately if swallowed.
    When using this product
    Do not apply any strong force or shocks to the product
    such as standing on, dropping or hitting it. Otherwise,
    the product may be broken, which may result in fire
    or electric shock. If it is damaged, turn off the power
    immediately, unplug the AC adapter and remove the
    batteries, and then contact the EPSON customer support
    centre. Continuous use may result in fire or electric
    shock.
    Take care not to spill any beverage such as tea, coffee or
    juice onto the product, or to spray aerosol insecticide. It
    may cause malfunction, fire, or electric shock. If any liquid
    has been spilled on the product, turn off the power, unplug
    the AC adapter and remove the batteries immediately,
    and then contact the EPSON customer support centre.
    Continuous use may result in fire or electric shock.
    Do not touch the printhead because it becomes very
    hot. Otherwise, there is a risk of burns.
    Do not open any covers other than the cover on the rear.
    Doing so may result in fire or electric shock. Always use
    the product as instructed in this manual. Otherwise,
    damage or injury may occur.
    If any of the following abnormalities is observed, turn
    off the power immediately, unplug the AC adapter
    and remove the batteries, and then contact the EPSON
    customer support centre.
    If smoke, strange odours or unexpected noises come
    from the product
    If liquid or foreign objects get inside the product
    If the product has been dropped or damaged
    When handling the cutter
    Do not touch the exit slot (where labels come out)
    during printing or when using the cutter, otherwise
    there is a risk of injury.
    Others
    Do not use or store the product, batteries, AC adapter,
    power cable, or tape cartridges in the following places.
    In direct sunlight.
    Where it may become extremely hot such as in a
    vehicle with the windows closed.
    Where it may become extremely hot such as near a
    heater or the temperature becomes very unstable such
    as near the exhaust duct of an air conditioner.
    Where the product may get wet due to a shower or rain
    such as in a bathroom or outdoors.
    In a dusty place or where the product may be exposed
    to smoke or steam such as near the kitchen or a
    humidifier.
    On an unstable place such as on a shaky table or on an
    inclined place.
    Where it might be subjected to vibration or shock.
    Near high-voltage power lines or something that
    generates a magnetic field.
    Keep the plastic bags used to contain the product or this
    manual out of reach of children. Children may suffocate
    if they swallow them or put their heads into the bags.
    CAUTION
    When handling batteries
    If liquid leaks from a battery, wipe it off with a cloth and
    replace it with a new one. If the liquid comes in contact
    with your skin, wash it away with water immediately.
    If the batteries are used incorrectly, they may cause
    leakage, overheating, explosion, erosion, or damage to
    the product, which may result in fire or injury.
    Do not use new ones and old batteries together, or mix
    different types of batteries.
    Use only AA Alkaline batteries. Rechargeable batteries
    cannot be used.
    Use batteries in the correct directions.
    Take the batteries out immediately when they have no
    power remaining.
    Take the batteries out if you do not use the product for
    a long time.
    Do not heat batteries or throw them in fire or water.
    Do not pinch the batteries with metal tweezers or
    use any pointed sharp metal object such as the tip of
    a mechanical pen or ball-point pen when taking the
    batteries out.
    When disposing of used batteries, make sure to follow
    the regulations.
    When using the AC adapter
    Do not unplug the AC adapter while the product is in
    operation, otherwise printing may not be successful.
    Do not use the AC adapter in a small, confined space,
    or cover it with a cloth. Otherwise, the AC adapter may
    overheat and deteriorate.
    When using this product
    Do not stand on the product or place it on an unstable
    place such as on a shaky table or on an incline.
    Otherwise, the product may fall and cause injury.
    To ensure safety, unplug this product before leaving it
    unused.
    Before cleaning, make sure to unplug the AC adapter
    from the outlet, and remove the batteries.
    Do not use a moistened cloth or solvents such as alcohol,
    thinner or benzine.
    When handling tape cartridges
    Make sure to use a dedicated LC Tape.
    Some types of tape cannot be cut by the cutter. For the details,
    refer to the tape's manual.
    Do not drop it or disassemble it. Doing so may cause damage.
    Do not pull out the tape forcibly by hand. But make sure to
    feed the tape with + . Otherwise, the tape cartridge may
    be broken and unusable.
    Avoid using a tape cartridge without remaining tape. Doing so
    may cause overheating of the printhead, which may result in
    damage or malfunction.
    MEMO
    Tape cartridges contain ink ribbons in them. When disposing
    tape cartridges, make sure to follow the local regulations for
    disposal.
    Other cautions
    Notes on usage
    Operate the keyboard gently.
    Do not touch the printhead.
    Take care not to cut your fingers when cutting the label with
    scissors.
    Do not attach a label on human bodies, living things, public
    facilities or other people’s belongings.
    About the printed labels
    Depending on the environment labels are used in and the
    nature of the object labels are attached to, the following issues
    may occur:
    Label: Discolouration, faded characters, peeling
    Adhesive side: Adhesive residue, staining, damage
    Carefully check the suitability of the label for the intended
    purpose before use.
    EPSON takes no responsibility for any damage or loss due to
    the above mentioned causes.
    Troubleshooting
    Problems
    Does not operate normally.
    Initialise this product if it does not operate normally such as the
    power cannot be turned on or off, or the display is interrupted.
    No image comes out even though has been
    pressed.
    Are the batteries correctly set?
    Check if all the batteries are correctly set.
    Did the batteries run out?
    Replace the batteries with new ones, or use the dedicated AC
    adapter (APT0615Z).
    Is the AC adapter securely connected?
    Connect the AC adapter and the power cable firmly to the
    power socket of the product, the AC adapter connector and the
    outlet.
    Are you using an AC adapter other than the dedicated one?
    Using an AC adapter other than the dedicated one (APT0615Z)
    is very dangerous, and may cause overheating or damage to the
    electric circuits.
    Is the display level appropriate?
    Adjust the display level.
    Display has turned off.
    Did you enable the auto power-off function?
    The power turns off automatically if no operation is made for
    more than 5 minutes.
    Did you try to carry out a function incorrectly?
    If buttons are operated incorrectly, the display turns off for a
    moment.
    Nothing is printed even though has been
    pressed.
    Is text entered?
    Nothing is printed if no text is entered.
    Any message on the display?
    Read the message and take the appropriate action.
    Did the tape run out?
    Install a new tape cartridge.
    Did the batteries run out?
    Replace the batteries with new ones, or use the dedicated AC
    adapter (APT0615Z).
    Is the cover on the rear open?
    Set the tape cartridge correctly and close the cover completely.
    MEMO
    If none of the above has solved the problem or the
    symptom is other than the above, contact the EPSON
    customer support centre.
    Insert Tape No tape cartridge is installed. Turn the power
    off and install a tape cartridge correctly.
    Check tape! A tape cartridge which cannot be used in
    this product has been set. Check the tape
    cartridge.
    Check tape
    cartridge
    A tape cartridge which cannot be used in
    this product has been set. Check the tape
    cartridge.
    Check battery Possible causes for this message are:
    No power remaining or inserted in the
    wrong way
    Mixed with other types or old ones
    If so, set the batteries correctly or replace
    them with new ones.
    Too many lines Text entered is too long.
    Press to delete the lines indicated by
    the cursor.
    Text too long Entered text is too long for the specified tape
    length. Press and adjust the tape length
    or make text shorter.
    Seq. num. only 1
    Sequence numbers have already been set.
    Sequence numbers can be used for one part only.
    Text will be
    deleted. OK?
    When creating a label with a special form,
    current text will be deleted. Press to delete
    the text and show the special form.
    Fill every digit Entered values for barcodes are wrong. Check
    the entries about values, digits, etc.
    Load wider tape Unable to print on the current tape. Use a
    wider tape.
    Txt is too long
    Continue?
    Entered text is too long for the specified tape
    length. Press to print in the correct length.
    Overheated! The printhead is too hot. Turn the power off
    and take out the tape cartridge. Wait for a
    while before start printing again.
    Cover open!
    Powering off.
    If you open the cover on the rear without
    turning the power off, a message is
    displayed and then the power is turned off
    automatically.
    Motor error! An error occurred in the motor operation.
    Turn the power off once, then turn it back on.
    If the same message appears, turn the power
    off and contact the EPSON customer support
    centre.
    Before use
    1. Preparing the power supply
    This product operates on batteries or with the dedicated
    AC adapter.
    Using on batteries
    c
    Prepare six AA alkaline batteries.
    1. Remove the cover on the rear.
    2. Insert the batteries.
    MEMO
    When continuing to install a tape cartridge, leave the
    cover off and go to Step 2.
    3. Close the cover. Close it until it snaps into place.
    Using with the AC adapter (APT0615Z)
    c
    Make sure to use the dedicated AC adapter
    (APT0615Z).
    1. Connect the AC adapter firmly into the power socket
    of the product.
    2. Plug the AC adapter into the outlet.
    2. Installing a tape cartridge
    1. Remove the slack of the ink ribbon.
    2. Remove the cover on the rear.
    3. Set the tape cartridge.
    Press it firmly until it snaps into place.
    When installing a new tape or the tip of the tape is
    longer than usual, put the tape through the "Tape
    Guide" slot.
    c
    Do not press the "Cut Button" before the tape stops.
    Do not pull the tape out with your fingers.
    4. Close the cover on the rear.
    Close it until it snaps into place.
    How to remove the tape cartridge
    c
    Hold the cartridge by the tabs, and lift it straight
    up.
    3. Turning the power on
    1. Press .
    When changing the language of messages on the
    display sDisplay Settings ("Display" menu)
    4. Feeding the tape
    c
    Do not press the "Cut Button" before the tape
    stops.
    After setting a tape cartridge, make sure to feed tape.
    1. Press + .
    2. Press .
    3. Cut the tape.
    Cut it by pressing the "Cut Button".
    5. Creating a label
    Example: ABC
    1. Press while holding down to enter text in
    capital letters.
    2. Press the following keys: , ,
    "ABC" appears on the display.
    Refer below for other operations and the labels you
    can create with this product.
    sEditing characters, Useful functions, Creating a
    label with a special form
    6. Printing labels
    1. Press .
    The length of the label to print and the number of
    prints appear, and printing starts.
    2. When the tape stops, press the "Cut Button" to cut
    the tape.
    c
    Do not press the "Cut Button" before printing is
    complete.
    Printing multiple labels continuously
    1. Press .
    The screen to enter the number of prints appears.
    2. Enter a value with number buttons and press .
    The length of the label to print and the number of
    prints appear, and printing starts.
    3. When the tape stops, press the "Cut Button" to cut
    the tape.
    A "cut mark" will be printed. Cut the tape with
    scissors.
    Adjusting print density
    1. When the power is off, press + .
    2. Adjust print density with , and press .
    MEMO
    In general, please set the value to the default; "0".
    7. Attaching labels
    1. Peel off the backing paper.
    2. Attach the label and rub it firmly.
    Turn the power off after use
    1. Press .
    Batteries:
    Take them out if not in use for a long time.
    AC adapter:
    Disconnect from the outlet and the product.
    Specifications
    Body
    Dimensions Approx. 110 (W) x 170 (D) x 56 (H) (mm)
    Weight Approx. 400g (excluding batteries, tape cartridge)
    Usage conditions
    Operating temperature 10 to 35 degrees C
    Storage temperature -10 to 55 degrees C
    Power supply
    AC adapter Type APT0615Z1-1
    Manufacturer
    Seiko Epson Corp.
    Input AC100-240V, 0.3A, 50-60Hz (dedicated
    adapter, power cable only)
    Output DC6.5V, 1.5A
    Total output
    power
    10W
    Battery AA alkaline battery x 6
    Supported tape width
    6 mm, 9 mm, 12 mm, 18 mm
    Editing characters
    Useful functions Creating a label with a special form
    c
    To create labels with a special form, a message
    confirming that the text will be deleted may
    appear when is pressed. Press to delete
    the current text and to show the special form.
    MEMO
    To exit the following special form mode, press ,
    then select the "Exit" and press .
    Creating an folder tab label
    File_01
    1. Press .
    2. Select from "Tab:Medium", "Tab:Small" or "Tab:
    Large" with , and press .
    3. Select a value with or enter label length, and
    press .
    Maximum length: 12.5cm (5.0 inch)
    4. Enter text.
    Creating a label for cables
    Flag labels wrapping a cable
    1. Press .
    2. Select from "Flag:Hori.", "Flag:Vert." or "Flag:Edge"
    with , and press .
    3. Select a value with or enter label length, and
    press .
    Maximum length: 12.5cm (5.0 inch)
    4. Enter text.
    Labels wrapping a cable
    U
    S
    B
    A
    0
    0
    1
    1. Press .
    2. Select "Wrap" with , and press .
    3. Select a value with or enter label length, and
    press .
    Maximum length: 12.5cm (5.0 inch)
    4. Enter text.
    Creating a label including a barcode
    Enter barcodes according to their standards.
    Check the printed labels with your barcode reader to ensure
    they can be correctly read.
    Supported barcode: CODE39, CODE128, ITF, CODABAR, UPC-A,
    UPC-E, EAN-8, EAN-13
    1. Press + .
    2. Select an item with , and press .
    3. After setting the barcode, enter the code.
    Display Settings ("Display" menu)
    The following are the settings to make operation easier.
    Backlight
    Turns the backlight of the display on or off.
    Backlight: On/Off
    Contrast
    Adjusts the density of the fonts on the display.
    Value: -5 to +5
    Language
    Selects the language of the settings and messages on the
    display.
    Language: English/Spanish/French/Portuguese-Br/
    Portuguese-EU/ Italian/Dutch/German
    inch:cm
    Selects the unit to indicate the length.
    Value: inch/cm
    Procedure
    1. Press + .
    2. Select a setting item with , and press .
    3. When the options of the selected item appear, select
    your choice with , and press .
    Initialising this product
    The product may stop functioning due to static electricity
    or other causes.
    Initialise the product if it does not operate normally such
    as the display is interrupted.
    c
    Initialise the product. Take extreme care before
    initialising it.
    All the created text will be deleted. The settings
    you made for character input will return to the
    default.
    1. Press .
    2. Press and hold + , and press .
    3. When a message appears, press .
    The product will be initialised.
    To abort: Press any button other than .
    Part Names and Functions
    8. Shift
    9. Caps Lock
    + : Capitalises the entered characters.
    10. Accent
    11. Space
    12. Shift
    13. Select/Enter
    14. Punctuation: A choice of marks.
    + : The other choice of marks.
    sAdding a punctuation mark to the label
    15. Delete, + : Deletes text.
    16. Symbol, + : To "Sequence number"
    menu.
    17. Special label, + : To "Bar code" menu.
    18. Print copies
    19. Preview, + : The "Display" menu.
    20. Cursor keys
    + , + : To the previous or next text.
    21. Print, + : Feeds the tape.
    22. Cut Button
    23. Display
    1
    2
    3
    4
    5
    67
    8
    9
    10
    11
    9. Cursor: Indicates the position where the operation is
    performed. This is the place where you enter text or
    delete symbols, etc.
    10. Head mark: Indicates what line it is in. Appears when
    multiple lines exist.
    MEMO
    : If this appears, you cannot print anything.
    11. Text number mark: Indicates the number of the
    current text counted from the beginning.
    Display
    You can check settings on the display. Indicators show
    whether or not settings are enabled.
    5. Style
    6. Setting
    7. Character keys
    1. Power, + : To "Print density" menu.
    1. Font size
    2. Font width
    3. Frame
    4. Font style
    5. Vertical
    6. Battery level (as a guide)
    7. Accent mark options
    8. Upper case/lower case
    This section explains various functions that will help you
    create labels.
    Changing the font size
    1. Press .
    2. Select a line layout with , and press .
    "Equal": Applies the same font size. No need to
    proceed to Step 3.
    3. Select a font size with , and press .
    Changing the font
    1. Press .
    2. Select a font with , and press .
    The font used for the entire text will change.
    Applying a font style
    1. Press .
    2. Select a style with , and press .
    c
    Styles applied to small or elaborate characters may
    not be able to print clearly.
    Adding a frame
    1. Press .
    2. Select an item with , and press .
    Entering the frame No. to select does the same.
    Available frames sSymbol List
    Specifying the label length
    1. Press .
    2. Select "Label length" with , and press .
    3. Select a value with or enter it, and press .
    Maximum length: 40cm (15.0 inch)
    "Auto": Adjusts to the proper length automatically.
    Adjusting the space between characters
    1. Press .
    2. Select "Char. spacing" with , and press .
    3. Select an item with , and press .
    Making the width of font narrower
    1. Press .
    2. Select "Narrow" with , and press .
    3. Select "Narrow" with , and press .
    Lining up characters vertically
    1. Press .
    2. Select "Vertical" with , and press .
    3. Select "On" with , and press .
    Using mirror writing for the label
    1. Press .
    2. Select "Mirror print" with , and press .
    3. Select "On" with , and press .
    Messages
    Characters are not printed properly.
    Is the tape cartridge correctly set?
    Set the tape cartridge correctly.
    Is the printhead dirty?
    Clean the printhead.
    Did the batteries run out?
    Replace them with new ones, or use the dedicated AC adapter
    (APT0615Z).
    Printing ends in the middle of text.
    Did the tape run out?
    Install a new tape cartridge.
    Did the batteries run out?
    Replace them with new ones, or use the dedicated AC adapter
    (APT0615Z).
    Created text has gone.
    Did you delete the text?
    If + are pressed, the text on the display will be deleted.
    Did you initialise the product?
    If the product is initialised, all the created text will be deleted.
    Did you remove the batteries or the AC adapter when the
    product was in operation?
    If the AC adapter or the batteries are removed during operation,
    the text may be deleted.
    Cannot attach the label.
    Did you peel the backing paper?
    Attach the label after peeling the backing paper.
    Are you attaching it on a dirty place or on a place with a rough
    surface?
    The label may not adhere due to the material of the attachment
    location or the environmental conditions.
    Cleaning
    When the exterior is dirty
    Wipe the dirt off with a soft cloth. If it is very dirty, use a
    cloth wrung out of water.
    c
    Never use chemicals or solvents such as benzine,
    thinner, or alcohol, or use a chemical duster.
    When the printhead is dirty
    If the print becomes faint or some
    parts are missing, there may be
    some dirt on the printhead.
    Clean the print head with a cotton
    swab moistened with medical
    alcohol (commercially available
    ethanol).
    Press character keys and enter text.
    sPart Names and Functions
    Text is entered from the cursor position. sDisplay
    c
    To keep the already entered text, first move the
    cursor to a number to which no text is entered yet
    with + or + , then enter text.
    Switching upper case or lower case
    1. Press + .
    The setting is indicated on the display. Characters
    are set to upper case or lower case.
    To capitalise partially: Enter with pressed.
    Deleting characters
    1. Press .
    Deletes one character backward.
    Breaking lines
    1. Press .
    Breaks the line from the character next to the cursor.
    Deleting text
    1. Press + .
    2. When a confirmation message appears, press .
    Text will be deleted.
    Confirming text
    1. Press .
    Text appears on the display.
    You can check the text and the length of the label.
    But the print image cannot be confirmed.
    Adding characters with an accent mark
    to the label
    If there is a choice of characters with an accent mark, they
    are indicated on the display.
    Example: École
    1. Press + .
    2. Press .
    A choice of characters with an accent mark appears.
    3. Select an item with , and press .
    Go on and enter the next character.
    Characters with an accent mark sSymbol List
    Adding a punctuation mark to the label
    Select from the following two methods.
    1. Press .
    Each press shows the next mark.
    Available marks
    1. Press + .
    Each press shows the next mark.
    Available marks
    Adding a symbol to the label
    1. Press .
    2. When the category appears, select an item with
    , and press .
    3. When symbols appear, select a symbol with
    , and press .
    Available symbols sSymbol List
    Creating labels with serial numbers
    (Sequence number)
    1. Press + .
    2. Enter a number/alphabet for the first label, and
    press .
    The number/alphabet increases by one whenever
    printing is done.
    Creating pieces of text
    You can create multiple pieces of text continuously. Up to
    50 pieces can be created at a time.
    You can check which piece of text you are creating with
    the text number mark displayed at the beginning.
    Creating another piece of text
    1. Select the next text number mark with + or
    + .
    You can create another piece of text. Do the same
    for the next pieces.
    Printing a selected piece of text
    1. Select a piece of text you want to print with +
    or + .
    2. Press .
    1
    2
    3
    4
    5
    6
    7
    8
    9
    11
    12
    13
    14
    15
    16
    17
    18
    19
    20
    21
    22
    23
    10
    If your product is faulty, please read the included
    warranty card and consult the store you purchased it
    from. If you require further assistance contact your local
    EPSON customer support centre.
    Please also find below the URL for the support centre:
    http://www.epson.co.uk/support
    2. Font
    3. Font size
    4. Frame
Epson LabelWorks LW-400

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Epson LabelWorks LW-400 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Epson LabelWorks LW-400 responder adecuadamente a su pregunta.

Vea el manual de Epson LabelWorks LW-400 aquí, de forma gratuita. Este manual pertenece a la categoría Impresoras de etiquetas y ha sido calificado por 1 personas con un promedio de 5.3. Este manual está disponible en los siguientes idiomas: Inglés. ¿Tiene alguna pregunta sobre Epson LabelWorks LW-400 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Epson LabelWorks LW-400

General
Marca Epson
Modelo LabelWorks LW-400
Producto Impresora de etiquetas
EAN 10343906273, 8715946492698
Idioma Inglés
Tipo de archivo PDF
Diseño
Pantalla LCD
Número de caracteres en pantalla 16
Número de líneas en pantalla 2
Diseño de teclado QWERTY
Color del producto Negro
Desempeño
Corte de cinta Manual
Número de lineas de impresión (max) 4
Cuchilla
Código de barras incorporado Code 39, EAN13, EAN8, ITF, UPC-A, UPC-E
Puertos e Interfaces
Ethernet -
Wifi -
Velocidad de la impresión
Resolución máxima 180 x 180DPI
Tecnología de impresión -
Color -
Máximo ancho de impresión 18mm
Altura máxima de impresión -mm
Impresión vertical
Impresión en modo espejo
Velocidad de impresión -
Control de energía
Numero de baterías soportadas 6
Tipo de batería AA
Certificado Energy Star -
Detalles técnicos
Indicador de nivel de batería
Dirección de papel
Longitud de listón 9m

Preguntas frecuentes

A continuación, encontrarás las preguntas más frecuentes sobre el Epson LabelWorks LW-400 .

¿Tu pregunta no está en la lista? Haz tu pregunta aquí

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más