Futaba SBD-1

Futaba SBD-1 manual

(2)
  • 󾙏
    CAUTION
    󾙍
    Do not connect any device (gyro, battery,
    etc.) other than servos to the servo
    connector of the SBD-1. There is the danger of
    erroneous operation or damage.
    󾙍
    Do not connect an S.BUS connector
    of the SBD-1 to other than an S.BUS
    servo connection port. There is the danger of
    erroneous operation or damage.
    󾙏
    WARNNG
    󾙋
    Always use in the state in which the
    SBD-1 is firmly attached to the fuselage
    of the airplane or helicopter. There is the danger
    of loss of control and crashing if the connector is
    disconncted by vibration and shock.
    Futaba Corp. will not be responsible for
    damage caused by combination with other
    than Futaba Genuine parts.
    S.BUS Decoder
    INSTRUCTION MANUAL
    Before using your new SBD-1, please read this manual
    thoroughly and use the system properly and safely.
    After reading this manual, store it in a safe place.
    •Channel setting by SBC-1
    1
    Connect the
    S.BUS
    connector of the
    SBD-1
    to the
    S.BUS
    servo connection port of the
    SBC-1
    .
    2
    C o nne c t t he b a t t er y t o t h e bat t e r y
    connection port of the
    SBC-1
    .
    * Status display LED blinks slowly. (About 1 sec/time)
    3
    Quickly press and release the
    SBC-1
    setting
    switch and select the servo connection port
    at which the channel is to be set.
    * Each time the switch is pressed, the set servo
    connection port and the number of times the LED
    blinks change.
    SBC-1
    SBD-1
    servo con-
    nector selection
    Sett i ng swi t ch
    operation
    LED display
    W h e n p o w e r
    turned on
    1 s h o r t b l i n k
    each second
    Connector (
    SX1
    )
    selected.
    Switch pressed
    a n d r e l e a s e d
    quickly
    2 sho r t blink s
    each second
    Connector (
    SX2
    )
    selected.
    Switch pressed
    a n d r e l e a s e d
    quickly
    3 sho r t blink s
    each second
    Connector (
    SX3
    )
    selected.
    * (Channel conrmation)
    When the operation position of the channel selector
    switch and the channel set at the connector during
    the SBD-1 servo connector selection coincide, the
    LED changes to a steady light.
    4
    Set the
    SBC-1
    channel selector switch to
    the channel you want to set.
    5
    Hold down the setting switch (about 1
    second).
    ©Copyright 2010. No part of this manual may be reproduced in any form without prior permission. The contents of this
    manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent
    errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made.
    FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
    1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
    1M23N23401 ©FUTABA CORPORATION 2010, 2 (1)
    Meaning of Special Markings
    Pay special attention to safety where indicated by the following marks:
    󾙏
    DANGER
    Procedures which may lead to dangerous conditions and
    cause death/serious injury if not carried out properly.
    󾙏
    WARNING
    Procedures which may lead to a dangerous condition or
    cause death or serious injury to the user if not carried out
    properly, or procedures where the probability of superficial
    injury or physical damage is high.
    󾙏
    CAUTION
    Procedures where the possibility of serious injury to the user
    is small, but there is a danger of injury, or physical damage,
    if not carried out properly.
    󾙍
    = Prohibited
    󾙋
    = Mandatory
    Usage Precautions
    Name of Each Part and Accessories
    Channel Setting
    Usage Method
    •Connection
    1
    Connect the
    S.BUS
    connector of the
    SBD-1
    to the receiver
    S.BUS
    connection port or
    S.BUS
    hub.
    2
    Connect a conventional servo or an
    S.BUS
    servo to the servo connector of the
    SBD-1
    .
    * When an S.BUS servo was connected, that servo
    will operate as a conventional servo. However,
    it operates on the channel set at the servo
    connector of the SBD-1 instead of the channel set
    at the servo itself.
    Thank you for purchasing an
    SBD-1
    ,
    S.BUS
    *1
    decoder. The
    SBD-1
    is a converter for using
    conventional servos (other than
    S.BUS
    servo
    *2
    ) with
    the
    S.BUS
    system.
    There are ve types of
    SBD-1
    available as follows.
    Type Total Length
    S.BUS
    Decoder
    SBD-1
    200 200mm (8in.)
    400 400mm (16in.)
    600 600mm (24in.)
    1100 1,100mm (43in.)
    1600 1,600mm (63in.)
    Before installing the
    SBD-1
    to the fuselage, set
    each channel at each servo connector (
    SX1
    ~
    3
    ).
    Use the
    SBC-1
    S.BUS
    channel changer or
    CIU-2
    USB adapter (
    PC-Link
    software for setting) to set
    the channel.
    * S.BUS decoder channel setting is impossible with
    the S.BUS receiver R6108SB.
    * PC-Link software can be downloaded from the
    home page of your region's Futaba importer.
    Conventional servo
    (or S.BUS servo)
    to the receiver
    S.BUS
    con-
    nection port or
    S.BUS
    hub
    SX1
    SX2
    SX3
    SBD-1
    Servo connector
    (Upper)
    SX1
    (Middle)
    SX2
    (Lower)
    SX3
    S.BUS connector
    [SBD-1 Ratings]
    •Dimensions:
    41.8x12.3x8.4mm
    (1.65x0.48x0.33in.)
    (excluding protruding)
    •Weight:
    6.9/10.8/14.7/24.5/34.3g
    (0.24/0.38/0.52/0.86/1.21oz.)
    •Powerrequirement:
    Ni-Cd, Ni-MH 4 to 5 cells
    equivalentbattery(Futaba)
    •O p e r a t i n g t e m p e r a t u r e
    range:-10to+45°
    *During channel setting, the LED blinks quickly
    (about 5 times/sec). When the LED changes to a
    steady light, channel setting is complete.
    6
    To s e t t h e c h a n n e l o f o t h e r s e r vo
    conne ction por ts, quickly p ress and
    release the setting switch and repeat steps
    4 and 5.
    <Accessories>
    Channel No. Label
    •Putthechannel No. labelon theservo connector
    fortheidenticationofchannelNo..
    Instruction manual (this manual)
    *1
    S.BUS
    : Serial communication system for Futaba R/C system
    *2
    Use the
    S.BUS
    hub as the extension code used for the
    S.BUS
    servo. Also
    SBD-1
    can be used.
Futaba SBD-1

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Futaba SBD-1 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Futaba SBD-1 responder adecuadamente a su pregunta.

Vea el manual de Futaba SBD-1 aquí, de forma gratuita. Este manual pertenece a la categoría Juguetes de radiocontrol y ha sido calificado por 2 personas con un promedio de 6.8. Este manual está disponible en los siguientes idiomas: Inglés. ¿Tiene alguna pregunta sobre Futaba SBD-1 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Futaba SBD-1

General
Marca Futaba
Modelo SBD-1
Producto Juguete de radiocontrol
EAN 4513886305696
Idioma Inglés
Tipo de archivo PDF
Características
Tipo de producto Decodificador
Marca compatible Futaba
Componente para Avión
Compatibilidad S.Bus
Color del producto Negro
Certificación CE
Número de canales de salida 3
Peso y dimensiones
Ancho 41.8mm
Profundidad 12.3mm
Altura 8.4mm
Longitud 1.6m
Peso 34.3g
Contenido del embalaje
Cantidad 1
Condiciones ambientales
Intervalo de temperatura operativa -10 - 45°C
Detalles técnicos
RoHS
Aviso de seguridad
No adecuado para niños de 0 a 3 años

Preguntas frecuentes

A continuación, encontrarás las preguntas más frecuentes sobre el Futaba SBD-1 .

¿Tu pregunta no está en la lista? Haz tu pregunta aquí

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más