Havis PKG-PSM-101 manual

Name: Havis PKG-PSM-101
Brand: Havis
SKU: 286733
Rating: 97 (1 reviews)

(1)

SPACER
OFFSET MOUNT
BASE
SEAT BOLT
SUPPLIED
WITH
HARDWARE KIT
(FIG. 2) C-HDM-104 SHOWN
VEHICLE MOUNTING BASE WITH SPACER
AND OFFSET BRACKET
PLACE THE SPACER AT THE
1.
SEATBOLT LOCATIONS TO FILL THE
GAP BETWEEN THE SEAT BRACKET
AND BASE.
(C-HDM-121 ONLY
REQUIRES A SPACER ON THE
DRIVERS SIDE BOLT).
ALIGN BASE MOUNTING HOLES TO
2.
SEATBOLT MOUNTING POINTS.
USING SUPPLIED SEATBOLTS,
INSERT BOLTS PASSING THROUGH
THE SPACER AND SEAT BRACKET
THEN HAND TIGHTEN TO AVOID
STRIPPING THE THREADS.
FULLY TIGHTEN SEAT BOLTS.
3.
(FIG. 4) C-HDM-103 SHOWN
VEHICLE MOUNTING BASE WITH FILLERS
BASE
FILLER
FILLER
SUPPLIED
WITH
HARDWARE KIT
REMOVE REAR SEATBOLTS. TILT THE SEAT
1.
FORWARD WHILE PULLING THE SEAT
TOWARDS THE REAR TO DISENGAGE
THE FRONT SEAT HOOKS.
ALIGN MOUNTING BASE CUT-OUT TO
2.
FRONT SEAT HOOK ENTRY. RETURN THE
SEAT TO ITS ORIGINAL LOCATION
WHILE HAVING THE BASE SANDWICHED
BETWEEN THE SEAT BRACKET AND
VEHICLE FLOOR. PUSH IN THE 2 FILLERS
ON EACH SIDE TO FILL THE GAP
BETWEEN THE SEAT BRACKET AND BASE.
SECURE THE FILLER USING SUPPLIED
HARDWARE. NOTE ONLY ONE KEY
SHAPED FILLER NEEDED ON DRIVERS
SIDE IF HUMP BRACKET IS BEING USED.
REATTACH REAR SEAT BOLTS AND
3.
FULLY TIGHTEN.
(FIG. 1) C-HDM-101 SHOWN
STANDARD NO HOLES DRILLED - VEHICLE
MOUNTING WITH OFFSET BRACKET

BASE
SUPPLIED
WITH
HARDWARE KIT
OFFSET MOUNT
LIFT THE SEAT AND PLACE BASE
1.
BETWEEN SEAT BRACKETS AND
VEHICLE FLOOR, ALIGN MOUNTING
HOLES TO SEATBOLT LOCATIONS. IN
SOME VEHICLES, THE SEATBOLTS ARE
ORIENTATED AT AN ANGLE, IF THIS IS
THE CASE, THE BASE WILL SIT ON TOP
OF THE SEAT BRACKET.
USING EXISTING SEATBOLTS, LOOSELY
2.
ATTACH ALL SEATBOLTS. USE CAUTION
WHEN THREADING THE BOLTS TO
AVOID STRIPPING THE THREAD.
FULLY TIGHTEN SEAT BOLTS.
3.
(FIG. 3) C-HDM-106 SHOWN
VEHICLE MOUNTING BASE (VAN APPLICATION)
BASE
(C-HDM-401)
INCLUDED IN
C-HDM-106/107
HARDWARE KIT
STIFFENER
BRACKET
LIFT THE SEAT AND PLACE BASE
1.
BETWEEN SEAT BRACKETS AND
VEHICLE FLOOR, ALIGN MOUNTING
HOLES TO SEAT BOLT MOUNTING
POINTS. SEE NOTE 3 ABOVE.
USING EXISTING SEATBOLTS, LOOSELY
2.
ATTACH ALL SEATBOLTS. USE CAUTION
WHEN THREADING THE BOLTS TO
AVOID STRIPPING THE THREADS.
ATTACH POLE ASSEMBLY USING
3.
SUPPLIED HARDWARE.
INSTALL SUPPORT ARM AS SHOWN
4.
USING HARDWARE SUPPLIED WITH C-
HDM-401 KIT. ENSURE THE C-HDM-401
DOES NOT CLAMP ABOVE THE
HORIZONTAL SLOT IN THE POLE.
INSTALL STIFFENER BRACKET AS
5.
SHOWN, DRILL AND BOLT TO THE SEAT
IF DESIRED.
FULLY TIGHTEN SEAT BOLTS.
6.
SUPPORT ARM
C-HDM-204, 205, 212, 213, 214, 215,
1.
216, 217 ARE NOT COMPATIBLE WITH
THE C-HDM-100 SERIES.
TO ATTACH C-HDM-204, 205, 214, 215
2.
LINE UP THE MOUNT WITH THE NUTS IN
THE CONSOLE, ATTACH USING 1/4-20
BOLTS. HOLES CAN BE DRILLED AND
THE MOUNT THROUGH BOLTED IF
NECESSARY.
TO MOUNT C-HDM-212, 213, 216, 217,
3.
HOLES MUST BE DRILLED AND THE
MOUNT THROUGH BOLTED USING THE
HARDWARE PROVIDED.
SEE NOTES FOR DRILLING
4.
1/4-20 x1/2" LG
1/4" SERRATED WASHER
C-HDM-103- see FIG. 4
C-HDM-104- see FIG. 2
C-HDM-105- see FIG. 2
C-HDM-106- see FIG. 3
C-HDM-107- see FIG. 3
C-HDM-109- see FIG. 2
C-HDM-121- see FIG. 2
C-HDM-124- see IND. INSTALL
C-HDM-131- see IND. INSTALL
C-HDM-133- see IND. INSTALL
C-HDM-134- see IND. INSTALL
C-HDM-135- see IND. INSTALL
STEP 1 C-HDM-100's INSTALLATION INSTRUCTIONS
VEHICLE PASSENGER SIDE MOUNTING BASE
INSPECT PARTS RECEIVED TO MAKE SURE YOU HAVE THE RIGHT BRACKETS FOR THE SPECIFIC VEHICLE.
1.
REMOVE ALL PLASTIC END CAPS COVERING THE SEAT BOLTS, IF APPLICABLE.
2.
REMOVE FRONT SEATBOLTS, IN SOME CASES REMOVING OR LOOSENING REAR SEATBOLTS WILL EASE
3.
THE INSTALLATION PROCESS. KEEP THE SEATBOLTS FOR RE-INSTALLATION. ON VAN HDMS THE LEFT SIDE
FRONT & REAR BOLTS ON THE PASSENGER SEAT SHOULD BE REMOVED ( HDM MOUNT ATTACHES TO
THE SIDE SEAT BOLTS).
IF OFFSET MOUNT IS SUPPLIED, IT'S RECOMMENDED TO INSTALL THIS AS THE LAST PROCESS. (SEE STEP 2)
4.
SEE THE RECOMMENDED INSTALL GUIDELINES LISTED BELOW TO IDENTIFY WHICH IS BEST FOR YOUR
5.
INSTALLATION. IF THE HDM BASE IS NOT LISTED IT EITHER HAS ITS OWN SPECIFIC INSTRUCTION OR
FOLLOWS THE SAME PROCESS AS FIGURE 1.
VISIT US AT www.havis.com TO SEE PICTURES OF INDIVIDUALLY INSTALLED PRODUCTS.
6.
FOR VEHICLE MOUNTING THAT REQUIRES DRILLING
INSPECT ALL AREAS BEFORE DOING ANY DRILLING
1.
ENSURE NO SERIOUS DAMAGE HAPPENS TO THE
VEHICLE.
SECURE THE MOUNT WITH SUPPLIED HARDWARE KIT.
2.
(FIG. 5) C-HDM-204 SHOWN
STANDARD NO HOLES DRILLED
CONSOLE MOUNTING

75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
TITLE:
DWG. NO.
REV
A
C-HDM-100-INST
4/6/10
HAVIS, INC.
INSTALLATION INSTRUCTIONS,
C-HDM-100's MOUNTING BASE

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Havis PKG-PSM-101 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Havis PKG-PSM-101 responder adecuadamente a su pregunta.

Acerca de Havis PKG-PSM-101

Vea el manual de Havis PKG-PSM-101 aquí, de forma gratuita. Este manual pertenece a la categoría Kits de montaje y ha sido calificado por 1 personas con un promedio de 9.7. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Havis PKG-PSM-101 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Havis PKG-PSM-101

General

Marca	Havis
Modelo	PKG-PSM-101
Producto	Kits de montaje
Idioma	Engels
Tipo de archivo	PDF

Detalles técnicos

Productos compatibles

Ford Crown Victoria 1995-2011

Color

Color del producto

Negro

Características

Productos compatibles	Ford Crown Victoria 1995-2011
Color del producto	Negro

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.