¿Tiene alguna pregunta sobre Havis PKG-PSM-120 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Havis PKG-PSM-120 responder adecuadamente a su pregunta.
Acerca de Havis PKG-PSM-120
Vea el manual de Havis PKG-PSM-120 aquí, de forma gratuita. Este manual pertenece a la categoría Kits de montaje y ha sido calificado por 1 personas con un promedio de 7.5. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Havis PKG-PSM-120 o necesita ayuda? Haz tu pregunta aquí
Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.
A-GUIDE RING BUSHING REMOVALWE STRONGLY RECOMMEND NOT TO REMOVE THEGUIDE RING BUSHING, BUT IF REMOVAL OF INNER POLEIS DESIRED - FOLLOW THIS SIMPLE REMOVALINSTRUCTIONINSERT MAXIMUM 1" DIAMETER OBJECT WITH1.SUFFICIENT LENGTH AND DROP INSIDE INNER POLE.MAKE SURE NOTHING PREVENTS GUIDE RING2.BUSHING FROM BEING EJECTED UNDERNEATH. HITWITH A HAMMER TO FORCE THE GUIDE RINGBUSHING OUT.7/8" - 1"DIAMETEROBJECTSUPPORT ARM(OPTIONAL)B -INSTALL SPIDER COLLAR (OPTIONALCOMES WITH C-HDM-401 & 403)IF MOUNTING THE SPIDER COLLAR TO THE INNER1.POLE USE CM003406 REDUCING BUSHING. SPREADAND SNAP OVER THE INNER POLE.LOOSELY ATTACH SPIDER COLLAR TO THE OUTER2.POLE OR CM003406. DO NOT MOUNT SPIDERCOLLAR ABOVE OUTER POLE HORIZONTAL CUT.SPIDER MUST BEBELOW THIS SLOTON THE OUTER POLEC -INSTALL OPTIONAL C-HDM-416IF MOUNTING C-HDM-416 TO THE INNER POLE USE1.CM003406. SPREAD THE PIECE AND IT SHOULD SNAPOVER THE INNER POLE.ATTACH C-PM-101 TO CLAMP ASSEMBLY USING2.LONG CARRIAGE BOLTS INSERTED THROUGH THEPRINTER AND ONE PIECE OF EXTRUSION.ATTACH POLE CLAMP TO THE OUTER POLE OR3.CM003406. AFFIX SECOND PIECE OF EXTRUSIONAROUND POLE AND LOOSELY TIGHTEN THEHARDWARE. DO NOT MOUNT CLAMP ABOVEOUTER POLE HORIZONTAL CUT.CM003406 REDUCINGBUSHING IS NECESSARYIF MOUNTING TOTHE INNER POLE.(USE ONLY ON FIXEDHEIGHT POLES)C-PM-101SOLD SEPARATELYD-INSTALL GAS SHOCK (OPTIONAL)(SKIP IF GAS SHOCK IS NOT IN USE)1.UNSCREW SMALL PLASTIC DISC FROM SHOCK2.INSERT GAS SHOCK ASSEMBLY UPWARD FROMTHE BOTTOM OF HDM POLE ASSEMBLY WITH GASSHOCK'S ROD FACING DOWNWARD. GASSHOCK WILL SANDWICH BETWEEN MOUNTINGBASE C-HDM-100 SERIES (NOT SHOWN) ANDACTION ADAPTER C-HDM-300 SERIES (NOTSHOWN).ONCE GAS SHOCK SITS PROUD OF THE INNER3.POLE REATTACH SMALL PLASTIC DISCGAS SHOCK(OPTIONAL)E -INSTALL C-HDM-409 OPTIONAL& COLLAR CLAMP ALIGNMENTTHIS CAN BE DONE EITHER AT THIS POINT OR ONCE1.THE C-HDM-100 SERIES BASE IS ALREADY IN THEVEHICLE. YOU WILL NEED THE OFFSET THAT WASWIITH THE C-HDM-100 BASE IF APPLICABLE.DECIDE ON THE ORIENTATION OF THE C-HDM-409.2.ENSURING THAT IF THE HANDLE VERSION OF THEPOLE IS BEING USED THE TWO SLOTS ARE NO MORETHAN 45 DEG APART IF THIS IS THE CASE ROTATE THEPOLE TO THE CORRECT POSITION.IF NO HANDLE IS BEING USED ENSURE THE OUTER3.POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.TIGHTEN ALL THE HARDWARE.4.F -INSTALL C-HDM-410-412 OPTIONALTHIS CAN BE DONE EITHER AT THIS POINT OR ONCE1.THE C-HDM-100 SERIES BASE IS ALREADY IN THEVEHICLE. YOU WILL NEED THE OFFSET THAT WASWIITH THE C-HDM-100 BASE IF APPLICABLE.DECIDE ON THE ORIENTATION OF THE OFFSET.2.ENSURING THAT IF THE HANDLE VERSION OF THEPOLE IS BEING USED THE TWO SLOTS ARE NO MORETHAN 45 DEG APART IF THIS IS THE CASE ROTATE THEPOLE TO THE CORRECT POSITION.IF NO HANDLE IS BEING USED ENSURE THE OUTER3.POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.TIGHTEN ALL THE HARDWARE.4.45°MAX.45°MAX.SLOTS IN TUBEAND CLAMPALIGNEDHAMMER75 JACKSONVILLE RD,WARMINSTER, PA. 189741-800-524-9900SIZESCALE: 1:8SHEET 1 OF 4DO NOT SCALE DRAWINGWEIGHT (LB): 12.109TITLE:DWG. NO.C-HDM_INSTREVA02/20/13HAVIS, INC.INSTALLATION INSTRUCTIONS, C-HDM MOUNTING BASES
