Havis PKG-PSM-244

Havis PKG-PSM-244 manual

(1)
  • SPACER
    OFFSET MOUNT
    BASE
    SEAT BOLT
    SUPPLIED
    WITH
    HARDWARE KIT
    (FIG. 2) C-HDM-104 SHOWN
    VEHICLE MOUNTING BASE WITH SPACER
    AND OFFSET BRACKET
    PLACE THE SPACER AT THE
    1.
    SEATBOLT LOCATIONS TO FILL THE
    GAP BETWEEN THE SEAT BRACKET
    AND BASE.
    (C-HDM-121 ONLY
    REQUIRES A SPACER ON THE
    DRIVERS SIDE BOLT).
    ALIGN BASE MOUNTING HOLES TO
    2.
    SEATBOLT MOUNTING POINTS.
    USING SUPPLIED SEATBOLTS,
    INSERT BOLTS PASSING THROUGH
    THE SPACER AND SEAT BRACKET
    THEN HAND TIGHTEN TO AVOID
    STRIPPING THE THREADS.
    FULLY TIGHTEN SEAT BOLTS.
    3.
    (FIG. 4) C-HDM-103 SHOWN
    VEHICLE MOUNTING BASE WITH FILLERS
    BASE
    FILLER
    FILLER
    SUPPLIED
    WITH
    HARDWARE KIT
    REMOVE REAR SEATBOLTS. TILT THE SEAT
    1.
    FORWARD WHILE PULLING THE SEAT
    TOWARDS THE REAR TO DISENGAGE
    THE FRONT SEAT HOOKS.
    ALIGN MOUNTING BASE CUT-OUT TO
    2.
    FRONT SEAT HOOK ENTRY. RETURN THE
    SEAT TO ITS ORIGINAL LOCATION
    WHILE HAVING THE BASE SANDWICHED
    BETWEEN THE SEAT BRACKET AND
    VEHICLE FLOOR. PUSH IN THE 2 FILLERS
    ON EACH SIDE TO FILL THE GAP
    BETWEEN THE SEAT BRACKET AND BASE.
    SECURE THE FILLER USING SUPPLIED
    HARDWARE. NOTE ONLY ONE KEY
    SHAPED FILLER NEEDED ON DRIVERS
    SIDE IF HUMP BRACKET IS BEING USED.
    REATTACH REAR SEAT BOLTS AND
    3.
    FULLY TIGHTEN.
    (FIG. 1) C-HDM-101 SHOWN
    STANDARD NO HOLES DRILLED - VEHICLE
    MOUNTING WITH OFFSET BRACKET
    BASE
    SUPPLIED
    WITH
    HARDWARE KIT
    OFFSET MOUNT
    LIFT THE SEAT AND PLACE BASE
    1.
    BETWEEN SEAT BRACKETS AND
    VEHICLE FLOOR, ALIGN MOUNTING
    HOLES TO SEATBOLT LOCATIONS. IN
    SOME VEHICLES, THE SEATBOLTS ARE
    ORIENTATED AT AN ANGLE, IF THIS IS
    THE CASE, THE BASE WILL SIT ON TOP
    OF THE SEAT BRACKET.
    USING EXISTING SEATBOLTS, LOOSELY
    2.
    ATTACH ALL SEATBOLTS. USE CAUTION
    WHEN THREADING THE BOLTS TO
    AVOID STRIPPING THE THREAD.
    FULLY TIGHTEN SEAT BOLTS.
    3.
    (FIG. 3) C-HDM-106 SHOWN
    VEHICLE MOUNTING BASE (VAN APPLICATION)
    BASE
    (C-HDM-401)
    INCLUDED IN
    C-HDM-106/107
    HARDWARE KIT
    STIFFENER
    BRACKET
    LIFT THE SEAT AND PLACE BASE
    1.
    BETWEEN SEAT BRACKETS AND
    VEHICLE FLOOR, ALIGN MOUNTING
    HOLES TO SEAT BOLT MOUNTING
    POINTS. SEE NOTE 3 ABOVE.
    USING EXISTING SEATBOLTS, LOOSELY
    2.
    ATTACH ALL SEATBOLTS. USE CAUTION
    WHEN THREADING THE BOLTS TO
    AVOID STRIPPING THE THREADS.
    ATTACH POLE ASSEMBLY USING
    3.
    SUPPLIED HARDWARE.
    INSTALL SUPPORT ARM AS SHOWN
    4.
    USING HARDWARE SUPPLIED WITH C-
    HDM-401 KIT. ENSURE THE C-HDM-401
    DOES NOT CLAMP ABOVE THE
    HORIZONTAL SLOT IN THE POLE.
    INSTALL STIFFENER BRACKET AS
    5.
    SHOWN, DRILL AND BOLT TO THE SEAT
    IF DESIRED.
    FULLY TIGHTEN SEAT BOLTS.
    6.
    SUPPORT ARM
    C-HDM-204, 205, 212, 213, 214, 215,
    1.
    216, 217 ARE NOT COMPATIBLE WITH
    THE C-HDM-100 SERIES.
    TO ATTACH C-HDM-204, 205, 214, 215
    2.
    LINE UP THE MOUNT WITH THE NUTS IN
    THE CONSOLE, ATTACH USING 1/4-20
    BOLTS. HOLES CAN BE DRILLED AND
    THE MOUNT THROUGH BOLTED IF
    NECESSARY.
    TO MOUNT C-HDM-212, 213, 216, 217,
    3.
    HOLES MUST BE DRILLED AND THE
    MOUNT THROUGH BOLTED USING THE
    HARDWARE PROVIDED.
    SEE NOTES FOR DRILLING
    4.
    1/4-20 x1/2" LG
    1/4" SERRATED WASHER
    C-HDM-103- see FIG. 4
    C-HDM-104- see FIG. 2
    C-HDM-105- see FIG. 2
    C-HDM-106- see FIG. 3
    C-HDM-107- see FIG. 3
    C-HDM-109- see FIG. 2
    C-HDM-121- see FIG. 2
    C-HDM-124- see IND. INSTALL
    C-HDM-131- see IND. INSTALL
    C-HDM-133- see IND. INSTALL
    C-HDM-134- see IND. INSTALL
    C-HDM-135- see IND. INSTALL
    STEP 1 C-HDM-100's INSTALLATION INSTRUCTIONS
    VEHICLE PASSENGER SIDE MOUNTING BASE
    INSPECT PARTS RECEIVED TO MAKE SURE YOU HAVE THE RIGHT BRACKETS FOR THE SPECIFIC VEHICLE.
    1.
    REMOVE ALL PLASTIC END CAPS COVERING THE SEAT BOLTS, IF APPLICABLE.
    2.
    REMOVE FRONT SEATBOLTS, IN SOME CASES REMOVING OR LOOSENING REAR SEATBOLTS WILL EASE
    3.
    THE INSTALLATION PROCESS. KEEP THE SEATBOLTS FOR RE-INSTALLATION. ON VAN HDMS THE LEFT SIDE
    FRONT & REAR BOLTS ON THE PASSENGER SEAT SHOULD BE REMOVED ( HDM MOUNT ATTACHES TO
    THE SIDE SEAT BOLTS).
    IF OFFSET MOUNT IS SUPPLIED, IT'S RECOMMENDED TO INSTALL THIS AS THE LAST PROCESS. (SEE STEP 2)
    4.
    SEE THE RECOMMENDED INSTALL GUIDELINES LISTED BELOW TO IDENTIFY WHICH IS BEST FOR YOUR
    5.
    INSTALLATION. IF THE HDM BASE IS NOT LISTED IT EITHER HAS ITS OWN SPECIFIC INSTRUCTION OR
    FOLLOWS THE SAME PROCESS AS FIGURE 1.
    VISIT US AT www.havis.com TO SEE PICTURES OF INDIVIDUALLY INSTALLED PRODUCTS.
    6.
    FOR VEHICLE MOUNTING THAT REQUIRES DRILLING
    INSPECT ALL AREAS BEFORE DOING ANY DRILLING
    1.
    ENSURE NO SERIOUS DAMAGE HAPPENS TO THE
    VEHICLE.
    SECURE THE MOUNT WITH SUPPLIED HARDWARE KIT.
    2.
    (FIG. 5) C-HDM-204 SHOWN
    STANDARD NO HOLES DRILLED
    CONSOLE MOUNTING
    75 JACKSONVILLE RD,
    WARMINSTER, PA. 18974
    1-800-524-9900
    SIZE
    TITLE:
    DWG. NO.
    REV
    A
    C-HDM-100-INST
    4/6/10
    HAVIS, INC.
    INSTALLATION INSTRUCTIONS,
    C-HDM-100's MOUNTING BASE
Havis PKG-PSM-244

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Havis PKG-PSM-244 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Havis PKG-PSM-244 responder adecuadamente a su pregunta.

Vea el manual de Havis PKG-PSM-244 aquí, de forma gratuita. Este manual pertenece a la categoría Kits de montaje y ha sido calificado por 1 personas con un promedio de 7.7. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Havis PKG-PSM-244 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Havis PKG-PSM-244

General
Marca Havis
Modelo PKG-PSM-244
Producto Kits de montaje
Idioma Engels
Tipo de archivo PDF
Detalles técnicos
Productos compatibles Dodge Charger 2011-2013
Características
Productos compatibles Dodge Charger 2011-2013

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2021 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más