Honeywell Sundial RF2 Y9520Z

Honeywell Sundial RF2 Y9520Z manual

  • User Guide
    Y9520Z Sundial RF
    Pack 5
    How to use:
    ST9520C Wireless Enabled 2 zone Programmer
    DT92E Wireless Room Thermostats
    BDR91T Wireless Enabled Relay Box (if installed)
    System Components
    Energy Efficiency and the Environment
    Home energy use is responsible for more than ¼ of the total UK carbon emissions
    which contribute to climate change. Heating and hot water systems based on
    boilers account for of this figure, so it is important to understand how your
    controls can help to maximize energy efficiency while maintaining your comfort.
    Your Programmer should be used in conjunction with appropriate temperature
    controls. In order to save energy the following general points should be observed:
    1. Ensure your system contains room thermostats in 2 seperate zones, and that
    both are set to appropriate temperature levels: typically 20°C for the main
    occupied zone and 18°C for the less occupied zone (typically the bedrooms).
    Programme your heating and hot water to be off when you are not in the house. If
    you are concerned about possible frost damage to any exposed pipe work, it is
    advisable to fit a frost protection system – your installer can advise you about this.
    3. Think about how you use your domestic hot water – if you have a storage
    system, it is not necessary to have this switched on all the time, even when you
    are in the house.
    4. Consider the heat up times required for your central heating. Every home
    responds differently when the heating is switched on. Adjust the start time so
    that you are not cold when you get up in the morning. A shorter heat up time is
    required for other heating periods.
    5. In the evening, when the house is up to temperature, it is often possible to
    switch off the heating up to an hour before you go to bed, without any noticeable
    reduction in comfort.
    This document is to be left with the user
    and forms part of a Home Information Pack
    This section is to be completed by the Installer
    Honeywell Control Systems Ltd.
    Arlington Business Park,
    RG12 1EB
    Technical Help Desk: 08457 678999
    50047645-006 A
    © 2011 Honeywell International Inc.
    Take care to dispose of this product and any
    packaging or literature in an appropriate way
    WHAT IS A PROGRAMMER? Explanation for Householders (as recommended by the Energy Savings Trust)
    Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and
    domestic hot water on and off at the same time, while others allow the domestic hot water and heating to
    come on and go off at different times. Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle. On some
    programmers you must also set whether you want the heating and hot water to run continuously, run under
    the chosen ‘On’ and ‘Off’ heating periods, or be permanently off. The time on the programmer must be
    correct. Some types have to be adjusted in spring and autumn at the changes between Greenwich Mean
    Time and British Summer Time. You may be able to temporarily adjust the
    heating programme, for example, ‘Override’, ‘Advance’, or ‘Boost’. These
    are explained in the manufacturer’s instructions. The heating will not work
    if the room thermostat has switched the heating off. And, if you have a hot-
    water cylinder, the water heating will not work if the cylinder thermostat
    detects that the hot water has reached the correct temperature.
    WHAT IS A ROOM THERMOSTAT? explanation for Householders (as recommended by the Energy Savings Trust)
    A room thermostat simply switches the heating system on and off as necessary. It works by sensing
    the air temperature, switching on the heating when the air temperature falls below the thermostat
    setting, and switching it off once this set temperature has been reached. Turning a room thermostat to
    a higher setting will not make the room heat up any faster. How quickly the room heats up depends on
    the design of the heating system, for example, the size of boiler and radiators. Neither does the setting
    affect how quickly the room cools down. Turning a room thermostat to a lower setting will result in the
    room being controlled at a lower temperature, and saves energy. The heating system will not work if
    a time switch or programmer has switched it off. The way to set and use your room thermostat is to
    find the lowest temperature setting that you are comfortable with, and then leave it alone to do its job.
    The best way to do this is to set the room thermostat to a low temperature – say 18ºC – and then turn
    it up by one degree each day until you are comfortable with the temperature. You won’t have to adjust
    the thermostat further. Any adjustment above this setting will waste energy and cost you more money.
    If your heating system is a boiler with radiators, there will usually be only one room thermostat to
    control the whole house. But you can have different temperatures in individual rooms by installing
    thermostatic radiator valves (TRVs) on individual radiators. If you don’t have TRVs, you should choose
    a temperature that is reasonable for the whole house. If you do have TRVs, you can choose a slightly
    higher setting to make sure that even the coldest room is comfortable, then prevent any overheating
    in other rooms by adjusting the TRVs.
    Room thermostats need a free flow of air to sense the temperature, so they must not be covered by
    curtains or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the
    thermostat from working properly.
    Zone 1
    (typically in living room or hallway)
    Zone 2
    (typically in bedroom or upstairs hallway)
    (If installed, typically next to boiler)
Honeywell Sundial RF2 Y9520Z

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Honeywell Sundial RF2 Y9520Z o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Honeywell Sundial RF2 Y9520Z responder adecuadamente a su pregunta.

Vea el manual de Honeywell Sundial RF2 Y9520Z aquí, de forma gratuita. Este manual pertenece a la categoría Controladores de temperatura y ha sido calificado por 1 personas con un promedio de 10. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Honeywell Sundial RF2 Y9520Z o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Honeywell Sundial RF2 Y9520Z

Marca Honeywell
Modelo Sundial RF2 Y9520Z
Producto Controlador de temperatura
Idioma Engels
Tipo de archivo PDF

¿Busca un manual? asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

© Copyright 2021 Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más