Horizon DYNC2015

Horizon DYNC2015 manual

(1)
  • Prophet™ Precept™ 80W LCD AC/DC Multi-Chemistry Battery Charger
    InstructIon Manual
    |
    BedIenungsanleItung
    |
    Manuel d’utIlIsatIon
    |
    Manuale dI IstruzIonI (dYnc2015)
    NOTICE
    All instructions, warranties and other collateral documents are subject to change
    at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit
    horizonhobby.com and click on the support tab for this product.
    Meaning of Special Language
    The following terms are used throughout the product literature to indicate various
    levels of potential harm when operating this product:
    NOTICE: Procedures, which if not properly followed, create a possibility of physical
    property damage AND a little or no possibility of injury.
    CAUTION: Procedures, which if not properly followed, create the probability of
    physical property damage AND a possibility of serious injury.
    WARNING: Procedures, which if not properly followed, create the probability of
    property damage, collateral damage, and serious injury OR create a high probability
    of superficial injury.
    WARNING: Read the ENTIRE instruction manual to become familiar with
    the features of the product before operating. Failure to operate the product
    correctly can result in damage to the product, personal property and cause
    serious injury.
    This is a sophisticated hobby product. It must be operated with caution and
    common sense and requires some basic mechanical ability. Failure to operate
    this Product in a safe and responsible manner could result in injury or damage
    to the product or other property. This product is not intended for use by
    children without direct adult supervision. Do not attempt disassembly, use with
    incompatible components or augment product in any way without the approval of
    Horizon Hobby, LLC. This manual contains instructions for safety, operation and
    maintenance. It is essential to read and follow all the instructions and warnings in
    the manual, prior to assembly, setup or use, in order to operate correctly and avoid
    damage or serious injury.
    Age Recommendation: Not for children under 14 years. This is not a toy.
    This appliance is not intended for use by persons with reduced physical, sensory
    or mental capabilities, or lack of experience and knowledge, unless they have
    been given supervision or instruction concerning use of the appliance by a person
    responsible for their safety.
    SAFETY PRECAUTIONS AND WARNINGS
    WARNING: Failure to exercise caution while using this product and comply
    with the following warnings could result in product malfunction, electrical
    issues, excessive heat, FIRE, and ultimately injury and property damage.
     
     
     
     
     
     
     
     -
    ning.
     
     
     
     
     
     
     
     
    
     
    to avoid short circuit between the charge leads. Reverse the sequence when
    disconnecting.
     
     
    charges.
     
     
    WARNING: Never leave charger unattended, exceed maximum charge rate,
    charge with non-approved batteries or charge batteries in the wrong mode.
    Failure to comply may result in excessive heat, fire and serious injury.
    CAUTION: Always ensure the battery you are charging meets the
    specifications of this charger and that the charger settings are correct. Not
    doing so can result in excessive heat and other related product
    malfunctions, which can lead to user injury or property damage. Please
    contact Horizon Hobby or an authorized retailer with compatibility questions.
    3
    Included Items:
    JST_XH Balance adapter
    Banana plug to EC3
    battery connector
    
    OPTIONAL ACCESSORIES
    DYN4012 - DC Power Cord
    DYN5006 - Charge Adapter Banana to Deans Male
    DYN5014 - Charge Adapter: Banana to Traxxas
    ®
    Male
    DYN5033 - Temperature Sensor
    SPECIFICATIONS
     
     
    Charge Current 
    Discharge Current 
    Operating Temperature 
    Balance Current Drain 
    Charging Mode 
    GETTING STARTED
    CAUTION: Never connect the AC and DC input cords to an active power source at the same time. This will void the warranty, cause product damage and possibly
    injure the user.
    A.
    H. I. J. K.
    L.
    F. G.B.
    C.
    D.
    E.
     
     
    C. Balance Circuit Adapter Board Connector
    D. Temperature Sensor Port
     
    F. DC Power Input Port
    G. AC Power Input Port
     
     
     
     
    L. LCD Screen
    PROGRAM SELECT
    LiPo BATT
    LiPo CHARGE
    4.6V 22.2V(6S)
    LiPo STORAGE
    2.5A 19.8V(6S)
    LiPo DISCHARGE
    5.0A 18.0V(6S)
    LiPo BALANCE
    5.5A 22.2V(6S)
    LiPo FAST CHG
    0.1A 7.4V(2S)
    PROGRAM SELECT
    Pb BATT
    Pb CHARGE
    0.1A 2.0V (1P)
    Pb DISCHARGE
    0.1A 2.0V (1P)
    PROGRAM SELECT
    NiMH BATT
    NiMH CHARGE Man
    CURRENT 0.1A
    NiMH DISCHARGE
    0.1A AUTO
    NiMH CYCLE
    DCHG>CHG 5
    PROGRAM SELECT
    NiCd BATT
    NiCd CHARGE Man
    CURRENT 0.1A
    NiCd DISCHARGE
    0.1A AUTO
    NiCd CYCLE
    DCHG>CHG 1
    USER SET
    PROGRAM->
    PROGRAM SELECT
    SAVE DATA
    Key Beep ON
    Buzzer ON
    SAVE [01] Pb
    2.0V 5000mAh
    Input Power Low
    Cut-Off 11.0V
    Waste Time
    CHG>DCHG 1min
    Capacity Cut-Off
    ON 5000mAh
    Saftey Timer
    ON 180min
    Temp Select
    Temp Cut-Off 80C
    NiMH Sensitivity
    D. Peak Default
    NiCd Sensitivity
    D. Peak Default
    LiPo/LiIo/LiFe
    LiPo
    V. Type 3.7V
    CHK Time 10min
    PROGRAM SELECT
    LOAD DATA
    LOAD [01] Pb
    2.0V 5000mAh
    PROGRAM SELECT
    LiPo BATT
    LiPo CHARGE
    4.6V 22.2V(6S)
    LiPo STORAGE
    2.5A 19.8V(6S)
    LiPo DISCHARGE
    5.0A 18.0V(6S)
    LiPo BALANCE
    5.5A 22.2V(6S)
    LiPo FAST CHG
    0.1A 7.4V(2S)
    PROGRAM SELECT
    Pb BATT
    Pb CHARGE
    0.1A 2.0V (1P)
    Pb DISCHARGE
    0.1A 2.0V (1P)
    PROGRAM SELECT
    NiMH BATT
    NiMH CHARGE Man
    CURRENT 0.1A
    NiMH DISCHARGE
    0.1A AUTO
    NiMH CYCLE
    DCHG>CHG 5
    PROGRAM SELECT
    NiCd BATT
    NiCd CHARGE Man
    CURRENT 0.1A
    NiCd DISCHARGE
    0.1A AUTO
    NiCd CYCLE
    DCHG>CHG 1
    USER SET
    PROGRAM->
    PROGRAM SELECT
    SAVE DATA
    Key Beep ON
    Buzzer ON
    SAVE [01] Pb
    2.0V 5000mAh
    Input Power Low
    Cut-Off 11.0V
    Waste Time
    CHG>DCHG 1min
    Capacity Cut-Off
    ON 5000mAh
    Saftey Timer
    ON 180min
    Temp Select
    Temp Cut-Off 80C
    NiMH Sensitivity
    D. Peak Default
    NiCd Sensitivity
    D. Peak Default
    LiPo/LiIo/LiFe
    LiPo
    V. Type 3.7V
    CHK Time 10min
    PROGRAM SELECT
    LOAD DATA
    LOAD [01] Pb
    2.0V 5000mAh
    PROGRAM SELECT
    LiPo BATT
    LiPo CHARGE
    4.6V 22.2V(6S)
    LiPo STORAGE
    2.5A 19.8V(6S)
    LiPo DISCHARGE
    5.0A 18.0V(6S)
    LiPo BALANCE
    5.5A 22.2V(6S)
    LiPo FAST CHG
    0.1A 7.4V(2S)
    PROGRAM SELECT
    Pb BATT
    Pb CHARGE
    0.1A 2.0V (1P)
    Pb DISCHARGE
    0.1A 2.0V (1P)
    PROGRAM SELECT
    NiMH BATT
    NiMH CHARGE Man
    CURRENT 0.1A
    NiMH DISCHARGE
    0.1A AUTO
    NiMH CYCLE
    DCHG>CHG 5
    PROGRAM SELECT
    NiCd BATT
    NiCd CHARGE Man
    CURRENT 0.1A
    NiCd DISCHARGE
    0.1A AUTO
    NiCd CYCLE
    DCHG>CHG 1
    USER SET
    PROGRAM->
    PROGRAM SELECT
    SAVE DATA
    Key Beep ON
    Buzzer ON
    SAVE [01] Pb
    2.0V 5000mAh
    Input Power Low
    Cut-Off 11.0V
    Waste Time
    CHG>DCHG 1min
    Capacity Cut-Off
    ON 5000mAh
    Saftey Timer
    ON 180min
    Temp Select
    Temp Cut-Off 80C
    NiMH Sensitivity
    D. Peak Default
    NiCd Sensitivity
    D. Peak Default
    LiPo/LiIo/LiFe
    LiPo
    V. Type 3.7V
    CHK Time 10min
    PROGRAM SELECT
    LOAD DATA
    LOAD [01] Pb
    2.0V 5000mAh
    PROGRAM SELECT
    LiPo BATT
    LiPo CHARGE
    4.6V 22.2V(6S)
    LiPo STORAGE
    2.5A 19.8V(6S)
    LiPo DISCHARGE
    5.0A 18.0V(6S)
    LiPo BALANCE
    5.5A 22.2V(6S)
    LiPo FAST CHG
    0.1A 7.4V(2S)
    PROGRAM SELECT
    Pb BATT
    Pb CHARGE
    0.1A 2.0V (1P)
    Pb DISCHARGE
    0.1A 2.0V (1P)
    PROGRAM SELECT
    NiMH BATT
    NiMH CHARGE Man
    CURRENT 0.1A
    NiMH DISCHARGE
    0.1A AUTO
    NiMH CYCLE
    DCHG>CHG 5
    PROGRAM SELECT
    NiCd BATT
    NiCd CHARGE Man
    CURRENT 0.1A
    NiCd DISCHARGE
    0.1A AUTO
    NiCd CYCLE
    DCHG>CHG 1
    USER SET
    PROGRAM->
    PROGRAM SELECT
    SAVE DATA
    Key Beep ON
    Buzzer ON
    SAVE [01] Pb
    2.0V 5000mAh
    Input Power Low
    Cut-Off 11.0V
    Waste Time
    CHG>DCHG 1min
    Capacity Cut-Off
    ON 5000mAh
    Saftey Timer
    ON 180min
    Temp Select
    Temp Cut-Off 80C
    NiMH Sensitivity
    D. Peak Default
    NiCd Sensitivity
    D. Peak Default
    LiPo/LiIo/LiFe
    LiPo
    V. Type 3.7V
    CHK Time 10min
    PROGRAM SELECT
    LOAD DATA
    LOAD [01] Pb
    2.0V 5000mAh
    PROGRAM SELECT
    LiPo BATT
    LiPo CHARGE
    4.6V 22.2V(6S)
    LiPo STORAGE
    2.5A 19.8V(6S)
    LiPo DISCHARGE
    5.0A 18.0V(6S)
    LiPo BALANCE
    5.5A 22.2V(6S)
    LiPo FAST CHG
    0.1A 7.4V(2S)
    PROGRAM SELECT
    Pb BATT
    Pb CHARGE
    0.1A 2.0V (1P)
    Pb DISCHARGE
    0.1A 2.0V (1P)
    PROGRAM SELECT
    NiMH BATT
    NiMH CHARGE Man
    CURRENT 0.1A
    NiMH DISCHARGE
    0.1A AUTO
    NiMH CYCLE
    DCHG>CHG 5
    PROGRAM SELECT
    NiCd BATT
    NiCd CHARGE Man
    CURRENT 0.1A
    NiCd DISCHARGE
    0.1A AUTO
    NiCd CYCLE
    DCHG>CHG 1
    USER SET
    PROGRAM->
    PROGRAM SELECT
    SAVE DATA
    Key Beep ON
    Buzzer ON
    SAVE [01] Pb
    2.0V 5000mAh
    Input Power Low
    Cut-Off 11.0V
    Waste Time
    CHG>DCHG 1min
    Capacity Cut-Off
    ON 5000mAh
    Saftey Timer
    ON 180min
    Temp Select
    Temp Cut-Off 80C
    NiMH Sensitivity
    D. Peak Default
    NiCd Sensitivity
    D. Peak Default
    LiPo/LiIo/LiFe
    LiPo
    V. Type 3.7V
    CHK Time 10min
    PROGRAM SELECT
    LOAD DATA
    LOAD [01] Pb
    2.0V 5000mAh
    PROGRAM SELECT
    LiPo BATT
    LiPo CHARGE
    4.6V 22.2V(6S)
    LiPo STORAGE
    2.5A 19.8V(6S)
    LiPo DISCHARGE
    5.0A 18.0V(6S)
    LiPo BALANCE
    5.5A 22.2V(6S)
    LiPo FAST CHG
    0.1A 7.4V(2S)
    PROGRAM SELECT
    Pb BATT
    Pb CHARGE
    0.1A 2.0V (1P)
    Pb DISCHARGE
    0.1A 2.0V (1P)
    PROGRAM SELECT
    NiMH BATT
    NiMH CHARGE Man
    CURRENT 0.1A
    NiMH DISCHARGE
    0.1A AUTO
    NiMH CYCLE
    DCHG>CHG 5
    PROGRAM SELECT
    NiCd BATT
    NiCd CHARGE Man
    CURRENT 0.1A
    NiCd DISCHARGE
    0.1A AUTO
    NiCd CYCLE
    DCHG>CHG 1
    USER SET
    PROGRAM->
    PROGRAM SELECT
    SAVE DATA
    Key Beep ON
    Buzzer ON
    SAVE [01] Pb
    2.0V 5000mAh
    Input Power Low
    Cut-Off 11.0V
    Waste Time
    CHG>DCHG 1min
    Capacity Cut-Off
    ON 5000mAh
    Saftey Timer
    ON 180min
    Temp Select
    Temp Cut-Off 80C
    NiMH Sensitivity
    D. Peak Default
    NiCd Sensitivity
    D. Peak Default
    LiPo/LiIo/LiFe
    LiPo
    V. Type 3.7V
    CHK Time 10min
    PROGRAM SELECT
    LOAD DATA
    LOAD [01] Pb
    2.0V 5000mAh
    PROGRAM SELECT
    LiPo BATT
    LiPo CHARGE
    4.6V 22.2V(6S)
    LiPo STORAGE
    2.5A 19.8V(6S)
    LiPo DISCHARGE
    5.0A 18.0V(6S)
    LiPo BALANCE
    5.5A 22.2V(6S)
    LiPo FAST CHG
    0.1A 7.4V(2S)
    PROGRAM SELECT
    Pb BATT
    Pb CHARGE
    0.1A 2.0V (1P)
    Pb DISCHARGE
    0.1A 2.0V (1P)
    PROGRAM SELECT
    NiMH BATT
    NiMH CHARGE Man
    CURRENT 0.1A
    NiMH DISCHARGE
    0.1A AUTO
    NiMH CYCLE
    DCHG>CHG 5
    PROGRAM SELECT
    NiCd BATT
    NiCd CHARGE Man
    CURRENT 0.1A
    NiCd DISCHARGE
    0.1A AUTO
    NiCd CYCLE
    DCHG>CHG 1
    USER SET
    PROGRAM->
    PROGRAM SELECT
    SAVE DATA
    Key Beep ON
    Buzzer ON
    SAVE [01] Pb
    2.0V 5000mAh
    Input Power Low
    Cut-Off 11.0V
    Waste Time
    CHG>DCHG 1min
    Capacity Cut-Off
    ON 5000mAh
    Saftey Timer
    ON 180min
    Temp Select
    Temp Cut-Off 80C
    NiMH Sensitivity
    D. Peak Default
    NiCd Sensitivity
    D. Peak Default
    LiPo/LiIo/LiFe
    LiPo
    V. Type 3.7V
    CHK Time 10min
    PROGRAM SELECT
    LOAD DATA
    LOAD [01] Pb
    2.0V 5000mAh
    PROGRAMMING QUICK GUIDE
    Press the Battery Type/Memory Button (H) to change among main menu screens or to get to these main menu screens from a submenu screen.
    Press the Select/Start Button (K) to get to submenus for adjusting operating parameters, to save value changes, or to start chosen battery charging actions.
    Press the Decrease (I) or Up (+) Buttons (J)
    JST_XH ADAPTER
    2S 3S 4S 6S5S
    Not to scale.
    Not all wiring shown.
    Not all connectors shown.
    LITHIUM BATTERIES (LI-PO)
    Ni-MH BATTERIES
    Pb BATTERIES
    Ni-Cd BATTERIES
    SAVE DATA
    LOAD DATA
    USER SET
    OPERATING YOUR CHARGER
    1 SELF TEST AND PROGRAM SELECT SCREENS
    LITHIUM
    2
    
    3 
    4
    
    5
    
    6
    
    7
    
    Ni-MH
    8
    
    9
    NI-MH CHARGING
    10 NI-MH DISCHARGING
    11 
    12 
    Ni-Cd
    13 NI-CD CHARGING
    14 NI-CD DISCHARGING
    15 
    Pb
    16 
    17 PB CHARGING
    18 PB DISCHARGING
    USER SETTINGS
    19 
    20 LOAD DATA
    21 
    a 
    b 
    c 
    d 
    e 
    f 
    g 
    h 
    i 
    j 
    22 
    23 
    TABLE OF CONTENTS
    1
    SELF TEST AND PROGRAM SELECT SCREENS
    arger is powered ON, there is a series of self tests and the screen will
    show the charger brand name and model number.
    DYNAMITE
    DYNC2015
    
    PROGRAM SELECT
    LiPo BATT
    From any screen, press the Battery Type/Memory Button (H) to go back to the
    main menu.
    2
    LITHIUM BATTERIES
    Press the Battery Type/Memory Button (H) to change among the 7 main menu screens
    and go to the PROGRAM SELECT Lithium BATT screen. Press the Select/Start Button (K)
    to enter this menu. This is the menu in which you set the standard Lithium battery charge
    parameters.
    
    
    
     section.
    LiPo CHARGE
    4.6A 22.2V(6S)
    Press the Down (–) Button (I) or Up (+) Button (J) to go to one of the control screens
    
    
    Select/Start Button (K) and adjust charging parameters
    as needed. Press and hold the Select/Start Button
    
    the charger compares the battery to charger settings. The screen will show battery and your
    settings information.
    (A) does not match, press the
    Battery Type/Memory Button and change the lithium battery charging parameters
    as needed. If the R: information matches S:, press the Select/Start Button to confirm.
    After confirmation, charging starts and information will show on the LCD screen.
    R: 3SER S:3SER
    CONFIRM (ENTER)
    A
    Li3S 2.0A 12.59V
    BAL 022:43 01082
    A
    B C D
    EF
    A. A Li-Po battery pack is balance charging
    B. Battery pack has 3 cells in series
    C. 
    D.
    E. 
    F.
    During charging, the Down (–) Button can be pressed to show several parameter
    
    
    Up (+) Button to see charge voltages for each cell and the Down (–) Button to return
    to the Charge Monitor screen. To change the charging rate during charging, press the
    Select/Start Button, then increase or decrease the rate using the Down (–) Button
    and Up (+) Button
    
    Press the Battery Type/Memory Button
    4.20 4.20 4.20
    0.00 0.00 0.00
    3
    LITHIUM CHARGING
    Press the Battery Type/Memory Button (H) until you reach the 7 main menus.
    Then press the Battery Type/Memory Button until you reach the PROGRAM
    SELECT Lithium BATT screen. Press the Select/Start Button (K) to enter this menu.
    Press the Down (–) Button (I) or Up (+) Button (J) to reach the CHARGE screen
    and set charging parameters. The charging amperage (A)
    (C) is dependent on the number of cells in series (B) and Lithium
    battery type.
    LiPo CHARGE
    4.6A 22.2V(6S)
    A
    BC
    To select values other than the existing parameters:
     Select/Start Button so the charge current value (A) flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    charge current value
     Select/Start Button again to save the value and the voltage value (C)
    flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    (B)
     Select/Start Button again to save the voltage value
    If no parameters are flashing, you can press the Down (–) Button or Up (+) Button to
    select another program such as BALANCE, FAST CHG, STORAGE or DISCHARGE.
    To start charging, press and hold the Select/Start Button for 3 seconds.
    CAUTION:
    process as batteries can cause fire, collateral damage and injuries.
    CAUTION:
    CAUTION:
    the Lithium charge programs will damage the battery or the charger.
    4
    LITHIUM BALANCING CHARGING
    This program menu is specifically designed for the balanced charging of Lithium
    batteries, including Li-Po, Li-Fe and Li-Ion battery packs. In balance charging, each
    cell in the battery pack is monitored and charged to the same capacity and voltage
    levels, ensuring the optimum performance of the pack. Balance charging requires a
    battery with a balance adapter connector and a balance adapter board that has been
    designed for your charger and your battery.
    Press the Battery Type/Memory Button (H) until you reach the 7 main menus.
    Then press the Battery Type/Memory Button until you reach the PROGRAM
    SELECT Lithium BATT screen. Press the Select/Start Button (K) to enter this menu.
    Press the Down (–) Button (I) or Up (+) Button (J) to reach the BALANCE screen and
    set charging parameters. The charging amperage (A) 
    (C) is dependent on the number of cells in series (B).
    LiPo BALANCE
    5.5A 22.2V(6S)
    A
    BC
    To select values other than the existing parameters:
     Select/Start Button so the charge current value (A) flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    charge current value
     Select/Start Button again to save the value and the voltage value (C)
    flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    (B)
     Select/Start Button again to save the voltage value
    If no parameters are flashing, you can press the Down (–) Button or Up (+) Button
    to select another program such as CHARGE, FAST CHG, STORAGE or DISCHARGE.
    To start charging, press and hold the Select/Start Button for 3 seconds.
    5
    LITHIUM FAST CHARGING
    Near the end of a standard charging cycle the charger switches from Constant
    
    the battery pack as close as possible to the maximum capacity. In Fast Charge, the
    
    final capacity of the battery will be less than what you would get using the standard
    charge method.
    Press the Battery Type/Memory Button (H) until you reach the 7 main menus.
    Then press the Battery Type/Memory Button until you reach the PROGRAM
    SELECT Lithium BATT screen. Press the Select/Start Button (K) to enter this menu.
    Press the Down (–) Button (I) or Up (+) Button (J) to reach the FAST CHG screen
    and set charging parameters.
    The charging amperage (A)(C) is
    dependent on the number of cells in series (B).
    LiPo FAST CHG
    0.1A 7.4V(2S)
    A
    BC
    To select values other than the existing parameters:
     Select/Start Button so the charge current value (A) flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    charge current value
     Select/Start Button again to save the value and the voltage value (C)
    flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    (B)
     Select/Start Button again to save the voltage value
    If no parameters are flashing, you can press the Down (–) Button or Increase
    Button to select another program such as CHARGE, BALANCE, STORAGE or
    DISCHARGE.
    To start charging, press and hold the Select/Start Button for 3 seconds.
    6
    LITHIUM STORAGE CHARGING
    
    
    
    -
    
    Press the Battery Type/Memory Button (H) until you reach the 7 main menus.
    Then press the Battery Type/Memory Button until you reach the PROGRAM
    SELECT Lithium BATT screen. Press the Select/Start Button (K) to enter this menu.
    Press the Down (–) Button (I) or Up (+) Button (J) to reach the STORAGE screen
    and set charging parameters.
    The charging amperage (A)(C) is
    dependent on the number of cells in series (B).
    LiPo STORAGE
    2.5A 11.1V(3S)
    A
    BC
    To select values other than the existing parameters:
     Select/Start Button so the charge current value (A) flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    charge current value
     Select/Start Button again to save the value and the voltage value (C)
    flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    (B)
     Select/Start Button again to save the voltage value
    If no parameters are flashing, you can press the Down (–) Button or Up (+) Button
    to select another program such as CHARGE, BALANCE, FAST CHG or DISCHARGE.
    To start charging, press and hold the Select/Start Button for 3 seconds.
    7
    LITHIUM DISCHARGING
    A battery pack’s capacity can be verified by discharging the pack to its minimum
    voltage level and measuring the current as the pack is discharged.
    Press the Battery Type/Memory Button (H) until you reach the 7 main menus.
    Then press the Battery Type/Memory Button until you reach the PROGRAM
    SELECT Lithium BATT screen. Press the Select/Start Button (K) to enter this menu.
    Press the Down (–) Button (I) or Up (+) Button (J) to reach the DISCHARGE
    screen and set discharging parameters.
    The discharging amperage (A)(C) is
    dependent on the number of cells in series (B).
    LiPo DISCHARGE
    5.0A 18.0V(3S)
    A
    BC
    To select values other than the existing parameters:
     Select/Start Button so the discharge current value (A) flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    discharge current value
     Select/Start Button again to save the value and the voltage value (C)
    flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    (B)
     Select/Start Button again to save the voltage value
    If no parameters are flashing, you can press the Down (–) Button or Up (+) Button to
    select another program such as CHARGE, BALANCE, FAST CHG or STORAGE.
    To start discharging, press and hold the Select/Start Button for 3 seconds.
    8
    NICKEL-METAL HYDRIDE (NI-MH) BATTERIES
    Press the Battery Type/Memory Button (H) to change among the 7 main menu
    screens and go to PROGRAM SELECT Ni-MH BATT screen. Press the Select/Start
    Button (K) to enter this menu. This is the menu in which you set the standard Ni-MH
    battery charge parameters.
    
     section.
    PROGRAM SELECT
    NiMH BATT
    Press the Down (–) Button (I) or Up (+) Button (J) to go to one of the control
    
    connect your Ni-MH battery to the charger. Press the Select/Start Button (K) and
    adjust charging parameters as needed. Press and hold the Select/Start Button
    
    sequence. After confirmation, charging starts and information will show on the LCD
    screen.
    NiMH 2.0A 7.59V
    CHG 022:43 01082
    A
    B C
    DE
    A. A Ni-MH battery pack is charging
    B. 
    C. 
    D.
    E. 
    During charging, the Down (–) Button or Up (+) Button can be pressed to show
    several parameter messages on the LCD screen including: Ni-MH Sensitivity, Capacity
    Cut-off, Safety Timer setting, Temperature Cut-off, External Temperature and Input
    
    
    Press the Battery Type/Memory Button
    CAUTION:
    Ni-MH charge programs will damage the battery or the charger.
    9
    NI-MH CHARGING
    Press the Battery Type/Memory Button (H) until you reach the 7 main menus.
    Then press the Battery Type/Memory Button until you reach the PROGRAM
    SELECT NiMH BATT screen. Press the Select/Start Button (K) to enter this menu.
    Press the Down (–) Button (I) or Up (+) Button (J) to reach the NiMH CHARGE
    screen and set charging parameters. The charging amperage (A) can be set between
    
    NiMH CHARGE Man
    CURRENT 0.1A
    A
    To select a value other than the existing parameter:
     Select/Start Button so the charge current value (A) flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    charge current value
     Select/Start Button again to save the value
    If no parameters are flashing, you can press the Down (–) Button or Increase
    Button
    To start charging, press and hold the Select/Start Button for 3 seconds.
    10
    NI-MH DISCHARGING
    A battery pack’s capacity can be verified by discharging the pack to its minimum
    voltage level and measuring the current as the pack is discharged.
    Press the Battery Type/Memory Button (H) until you reach the 7 main menus.
    Then press the Battery Type/Memory Button until you reach the PROGRAM
    SELECT NiMH BATT screen. Press the Select/Start Button (K) to enter this menu.
    Press the Down (–) Button (I) or Up (+) Button (J) to reach the NiMH
    DISCHARGE screen and set discharging parameters. The discharging amperage (A)
    (B)
    
    NiMH DISCHARGE
    0.1A AUTO
    BA
    To select values other than the existing parameters:
     Select/Start Button so the discharge current value (A) flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    discharge current value
     Select/Start Button again to save the value and the voltage value (B)
    flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the voltage
     Select/Start Button again to save the voltage value
    If no parameters are flashing, you can press the Down (–) Button or Increase
    Button
    To start discharging, press and hold the Select/Start Button for 3 seconds.
    11
    NI-MH CYCLE CHARGING
    
    program. Cycling Ni-MH batteries can increase capacity and rejuvenate neglected
    batteries. Discharge capacity and average battery voltage help you compare batteries
    for the best run time and power.
    Press the Battery Type/Memory Button (H) until you reach the 7 main menus.
    Then press the Battery Type/Memory Button until you reach the PROGRAM
    SELECT NiMH BATT screen. Press the Select/Start Button (K) to enter this menu.
    Press the Down (–) Button (I) or Up (+) Button (J)
    
    NiMH CYCLE
    DCHG>CHG 5
    BA
    To select values other than the existing parameters:
     Select/Start Button so the cycle type (A) flashes
     Down (–) Button or Up (+) Button to set the cycle type as
    CHG>DCHG or DCHG>CHG
     Select/Start Button again to save your choice and the number of
    cycles (B) flashes
     Down (–) Button or Up (+) Button to DECREASE or INCREASE the
    
     Select/Start Button again to save the cycle count value
    If no parameters are flashing, you can press the Down (–) Button or Increase
    Button to select another program such as CHARGE or DISCHARGE.
    To start cycling, press and hold the Select/Start Button for 3 seconds.
    When Using an External DC Power Source:
     DC Power Input Port (F).
     
     LCD Screen (L).
    NOTICE: Always connect cable polarities correctly.
    NOTICE:
    using with sources other than a standard AC wall outlet.
    When Using an External AC Power Source:
     AC Power Input Port (G).
     
     LCD Screen (L).
    CAUTION: Always power ON the charger before connecting a battery, or damage to the charger and the battery can result.
     
     
     
     
Horizon DYNC2015

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Horizon DYNC2015 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Horizon DYNC2015 responder adecuadamente a su pregunta.

Vea el manual de Horizon DYNC2015 aquí, de forma gratuita. Este manual pertenece a la categoría Cargadores de acumulador y ha sido calificado por 1 personas con un promedio de 9.4. Este manual está disponible en los siguientes idiomas: Inglés. ¿Tiene alguna pregunta sobre Horizon DYNC2015 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Horizon DYNC2015

General
Marca Horizon
Modelo DYNC2015
Producto Cargador de acumulador
EAN 0605482552209
Idioma Inglés
Tipo de archivo PDF
Puertos e Interfaces
Video componente (YPbPr/YCbCr) entrada -
Entrada de video compuesto -
Salida de video compuesto -
Entrada de audio (L,R) -
Salida de audio (L,R) -
Audio digital, salida optica -
Audio digital, salida coaxial -
Salidas para auriculares -
Puerto - RS-232 -
Puertos RS-232C -
Cantidad de puertos SCART -
Número de puertos RF -
Entrada de S-Video -
Cantidad de puertos VGA (D-Sub) -
Otras características
Número de canales (señal analógica) -
Número de canales (DVB-C) -
Número de canales (DVB-S2) -
Número de canales (DVB-T) -
Características
La tensión de carga -V
Color del producto Rojo
Pantalla incorporada
Tipo de visualizador LCD
Conector -
Corriente de salida 2A
Peso y dimensiones
Ancho 140mm
Profundidad 150mm
Altura 60mm

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más