ICOM HM-162B

ICOM HM-162B manual

(1)
  • INSTRUCTIONS
    REMOTE-CONTROL MICROPHONE
    HM-162B/SW
    Thank you for purchasing the HM-162B/SW
    REMOTE
    -
    CONTROL MICROPHONE
    . The COMMANDMIC III
    TM
    is a
    remote control microphone for use with the IC-M604
    or else.
    Please read the connected transceiver’s instruction
    manual carefully before installation and operation.
    These instructions are just described the remote-
    control operations only.
    q BUSY/TRANSMIT INDICATOR
    BBUUSSYY
    ” appears when receiving a signal or when the
    squelch opens.
    TTXX
    ” appears while transmitting.
    w RECEIVER ATTENUATOR INDICATOR
    LLOOCC
    ” appears when the Attenuator function is in use.
    e SCRAMBLER INDICATOR
    SSCCRRAAMM
    ” appears when an optional voice scrambler is acti-
    vated.
    r SCAN INDICATOR
    Either “
    NNOORRMMAALL SSCCAANN
    ” or “
    PPRRII--SSCCAANN 1166
    ” scan type
    appears while scanning.
    DDUUAALL 1166
    ” appears during dualwatch; “
    TTRRII 1166
    ” ap-
    pears during tri-watch.
    t SELECTOR STATUS INDICATOR
    Indicates the [SELECTOR] active status;
    [[VVOOLL]]
    ” appears when [SELECTOR] as the audio volume.
    [[SSQQLL]]
    ” appears when [SELECTOR] as the noise squelch
    controller.
    [[CCHH ]]
    ” appears when [SELECTOR] as the channel selector.
    y POSITION INDICATOR
    Shows the GPS position data.
    •“
    ????
    ” may blink every 2 sec. instead of position data when
    the GPS position data is invalid. In this case, the last position
    data is held for up to 23.5 hours.
    •“
    ????
    ” may blink every 2 sec. instead of position data 4 hours
    after the position data is input manually, up until 23.5 hours
    have past.
    NNoo PPoossiittiioonn
    ” appears when no GPS receiver is con-
    nected and no position data is input manually.
    u TIME ZONE INDICATOR
    LLooccaall
    ” appears when the offset time data in the ‘Set
    up’ menu is entered.
    NNoo TTiimmee
    ” appears when no GPS receiver is connected
    and no time data is input manually.
    i CHANNEL COMMENT INDICATOR
    Channel comment appears, if programmed.
    o CHANNEL NUMBER READOUT
    Indicates the selected operating channel number.
    !0 KEY LOCK INDICATOR
    Appears while the Key Lock function is in use.
    Blinks while the All Key Lock function is in use.
    !1 LOW BATTERY INDICATOR
    “” blinks when the battery voltage drops to approx. 10 V
    DC or below.
    !2 CALL CHANNEL INDICATOR
    CCAALLLL
    ” appears when the call channel is selected.
    AALLEERRTT
    ” appears when the Weather Alert function is in
    use; blinks when an alert tone is received.
    !3 CHANNEL GROUP INDICATOR
    Indicates whether an International “
    IINNTT
    ,” U.S.A. “
    UUSSAA
    ,”
    Canadian “
    CCAANN
    ” or weather “
    WWXX
    ” channel is selected.
    !4 DUPLEX INDICATOR
    Appears when a duplex channel is selected.
    Duplex channel has a different TX and RX frequency.
    !5 TAG CHANNEL INDICATOR
    Appears when a tag channel is selected.
    !6 POWER INDICATOR
    2255WW
    ” appears when high power is selected.
    11WW
    ” appears when low power is selected.
    !7 RX SPEAKER INDICATOR
    Appears when an RX speaker function is activated.
    BUSYBUSY-25W25W------INTINT------CALLCALL
    LOCLOC- -- -- DUPDUP
    SCRAMSCRAM--TAGTAG
    NORMALNORMAL-SCANSCAN
    -3434°34.506N34.506N
    123123°23.236W23.236W
    LocalLocal----1:101:10- - CALLINGCALLING
    RXRX
    [VOL]
    w
    q
    e
    y
    u
    r
    t
    !6!7 !4!5 !3 !2
    o
    !0
    !1
    i
    Accessories included with the HM-162B/SW: Qty.
    q Connection cable (OPC-1540*: 6 m; 20 ft) ....................... 1
    w Mounting base .................................................................. 1
    e Connector cap .................................................................. 1
    r Microphone hanger .......................................................... 1
    t Screws (M3 × 16; tapping) ............................................... 5
    *: OPC 1540 has external speaker leads as illustrated at right.
    (Yellow: Audio, Black: Speaker ground)
    These instructions are described when the HM-162 is connected to the IC-M604. Some operations or indications may be dif-
    ferent as these instructions depending on the connecting transceiver.
    x Function display
    z HM-162B/SW supplied accessories
    qwe
    r
    t
    Yellow
    Black
    1
ICOM HM-162B

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre ICOM HM-162B o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de ICOM HM-162B responder adecuadamente a su pregunta.

Vea el manual de ICOM HM-162B aquí, de forma gratuita. Este manual pertenece a la categoría Amplificadores y ha sido calificado por 1 personas con un promedio de 8.6. Este manual está disponible en los siguientes idiomas: Inglés. ¿Tiene alguna pregunta sobre ICOM HM-162B o necesita ayuda? Haz tu pregunta aquí

Especificaciones de ICOM HM-162B

General
Marca ICOM
Modelo HM-162B
Producto Amplificador
Idioma Inglés
Tipo de archivo PDF

Preguntas frecuentes

A continuación, encontrarás las preguntas más frecuentes sobre el ICOM HM-162B .

¿Tu pregunta no está en la lista? Haz tu pregunta aquí