JVC RV-NB50

JVC RV-NB50 manual

(1)
  • Inserting batteries
    Main unit
    PREPARATION
    NOTE
    The power will not be supplied through the batteries when the power is supplied
    through the AC outlet or car battery on the unit.
    The battery is consumed more quickly than usual when operating the unit
    continuously or operating it in a cold place.
    When the power is supplied using the batteries, the display will be blank when the
    unit is turned off (at standby).
    When the power is supplied using the batteries, the unit is turned on by pressing
    or source buttons on the main unit.
    CAUTION
    To avoid battery leakage or explosion, handle batteries properly.
    If you are not going to use this unit for a month or more, remove the batteries from
    the battery compartment.
    Dispose of batteries in the proper manner, according to federal, state, and local
    regulations.
    Do not mix with batteries of different types or with new and old ones.
    Do not attempt to charge any batteries other than rechargeable ones.
    Discard leaky batteries immediately. Battery leakage can cause skin burns or other
    personal injuries.
    If chemicals leak onto the unit, clean the unit completely.
    Match the polarities (+ and –) of the batteries.
    Remote control
    If the range or effectiveness of the remote control decreases, replace the batteries.
    Cautions when connecting to the car adapter
    Be sure to use the car adapter (not supplied) with the same
    polarity design as the one equipped with this unit to prevent
    mishaps or damage.
    For safety, stop the car before performing operations.
    Be sure to start the engine when you use the car adapter;
    otherwise, the car battery will be exhausted.
    During transport, stabilize the unit in a box, etc.
    To prevent malfunctions, do not leave the unit in a car for a
    long time.
    Connecting the power cord
    Battery compartment
    Discs CDs with one of the marks below on
    the surface.
    Files Files in audio CD format, MP3/WMA
    files on a finalized CD-R or CD-RW.
    MP3/WMA files in a USB device can
    also be played.
    Playable discs/files
    Hierarchy
    Level 1 Level 2 Level 3 Level 4 Level 5
    Folder with its play order
    MP3/WMA track with its play order
    MP3/WMA folders/tracks configuration
    MP3/WMA discs require a longer readout
    time than regular CDs. (It depends on the
    complexity of the folder/file configuration.)
    Some MP3/WMA files cannot be played back
    and will be skipped. This results from their
    recording processes and conditions.
    When making MP3/WMA discs, use ISO 9660
    Level 1 for the disc format.
    This unit can play back MP3/WMA files with
    the extension code <.mp3> or <.wma>
    (regardless of the letter case upper/lower).
    It is recommended that you make each MP3
    file at a sampling rate of 44.1 kHz and at a bit
    rate of 128 kbps. Similarly each WMA file at a
    sampling rate of 44.1 kHz and at a bit rate of
    96 kbps.
    Playback order of MP3/ WMA files may be
    different from the one you have intended
    when recording. If a folder does not contain
    MP3/ WMA files, it is ignored.
    This unit cannot play packet write” discs.
    If a CD-RW has been recorded in a different
    format, erase all data on the CD-RW
    completely before recording on it.
    This unit can recognize up to a total of 511
    tracks and folders on a disc, and 65536 files
    in up to 200 groups (maximum 500 files in a
    single group) on a USB device.
    For connecting/disconnecting:
    USB Memory and DAPs compatible with the USB
    mass storage class specifications are connectable.
    Always set the volume to the minimum level when
    connecting or disconnecting a USB device.
    When connecting with a USB cable, use the USB 2.0
    cable less than 1 m (3.28 ft) in length.
    You cannot connect a computer to the USB
    MEMORY terminal of the unit.
    Connect one USB device to the unit at a time. Do
    not use a USB hub.
    When the power is supplied through the AC outlet
    or car battery and USB is selected as the source, the
    USB device is charged through the USB MEMORY
    terminal, however some USB devices may not be
    charged.
    For playing back:
    When connecting a USB device, refer also to its
    manual.
    You can play back MP3/WMA files on a USB device
    (maximum data transfer rate: 2 Mbps). This unit may
    not play back some files even though their formats
    are listed above.
    While playing back a file in a USB device, do
    not disconnect the USB device. It may cause
    malfunction of both this unit and the device.
    This unit is compatible with USB 2.0 Full Speed.
    You cannot play back a file larger than 2 Gigabytes.
    When playing a file of a large transfer rate, sounds
    may be dropped during playback.
    This unit cannot recognize a USB mass storage class
    device whose rating exceeds 5V/500 mA.
    You cannot send any data to your USB device from
    this unit.
    Some USB devices may not be recognized or may
    not work properly.
    Some DAPs are not compatible with the unit.
    Copyrighted tracks (WMA-DRM* tracks) cannot be
    played back on the unit.
    Coded or encrypted tracks in a special method
    cannot be played on the unit.
    Electrostatic shock at connecting a USB device may
    cause abnormal playback of the device. In this case,
    disconnect the USB device then reset this unit and
    the USB device.
    JVC bears no responsibility for any loss of data in
    the USB mass storage class device while using this
    unit.
    * DRM (Digital Rights Management): Any of several
    technical methods used to control or restrict the
    use of digital media content on electronic devices
    with such technologies installed.
    • Compatible iPod:
    iPod model
    iPod nano
    iPod nano (2nd Generation)
    iPod nano (3rd Generation)
    iPod nano (4th Generation)
    iPod mini
    iPod mini (2nd Generation)
    iPod (4th Generation)
    iPod classic
    iPod photo (4th Generation)
    iPod video (5th Generation)
    iPod touch
    iPod touch (2nd Generation)
    Sound distortion may occur when playing back
    audio sources with high recording levels. When
    distortion occurs, it is recommended to turn
    off the equalizer of iPod. For information on
    operating iPod, see the iPod instruction manual.
    Important for USB mass storage class
    device
    NOTE
    The power can also be supplied through the batteries (see the
    instruction on the right) and the car battery (see below).
    A small amount of power is always consumed even while on
    standby.
    CAUTION
    Only use JVC power cord provided for this unit to avoid
    malfunction or damage to the unit.
    Remove all the batteries when using the power cord or car
    battery.
    Be sure to unplug the power cord from the outlet when going
    out or when the unit is not in use for an extended period of
    time.
    Unplug the AC power cord from the unit to supply the
    power through the car battery or batteries in the battery
    compartment; otherwise, the unit does not work.
    Maintenance
    Troubleshooting
    Display
    1 Timer indicators
    (timer), ON
    2 SLEEP indicator
    3 CLOCK indicator
    4 iPod indicator
    5 FM mode indicators
    STEREO, MONO
    6 Repeat indicators
    , ALL, GROUP
    7 Main display
    8 PRGM (program) indicator
    9 RANDOM indicator
    0 Frequency unit indicators
    iPod is a trademark of Apple Inc., registered in
    the U.S. and other countries.
    “Made for iPod” means that an electronic
    accessory has been designed to connect
    specifically to iPod and has been certified by
    the developer to meet Apple performance
    standards.
    Apple is not responsible for the operation of
    this device or its compliance with safety and
    regulatory standards.
    Important for iPod devices
    Disc player
    CD capacity: 1CD
    Signal-to-noise ratio: 85 dB
    Dynamic range: 90 dB
    Tuner
    FM tuning range: 87.5 MHz –
    108.0 MHz
    Antenna: FM telescopic
    antenna
    General
    Speakers:
    • Full range:
    • Super woofer:
    8 cm (3 3/16”)
    cone x 2
    Speaker impedance:
    16 Ω
    13 cm (5 1/8”)
    cone x 2
    Speaker impedance:
    7 Ω
    Output power: 40 W
    Input terminal:
    • USB:
    Dock for iPod:
    • DC IN:
    Playable files:
    MP3, WMA
    • Compatible device:
    Mass storage class
    • Output power:
    DC 5 V
    500 mA
    DC 5 V
    500 mA
    DC 12 V
    Output terminal:
    PHONES (φ3.5) x 1
    As an ENERGY STAR ® Partner,
    JVC has determined that
    this product or product
    models meet the E
    NERGY STAR®
    guidelines for energy efficiency.
    SPECIFICATIONS
    Power supply: AC 120 V , 60 Hz
    DC 15 V (R20 (SUM-1)/D
    (13D)-size batteries x 10)
    External DC 12 V
    (Car battery via the optional
    car adapter)
    Power
    consumption: AC 120 V
    , 60 Hz:
    28 W (at operation)
    1 W (on standby)
    External DC 12 V
    2 A (power on mode)
    Dimensions: 666 mm (26 1/4”) x
    231 mm (9 1/8”) x 240 mm
    (9 1/2”) (W/H/D)
    Mass:
    Approx. 6.8 kg (15.0 lbs)
    (without batteries stored in
    the battery compartment)
    Accessories
    provided: Power cord x 1
    Remote control x 1
    Shoulder belt x 1
    Buckle x 2
    Stopper x 2
    Design and speci cations are subject to change
    without notice.
    Microsoft and Windows Media are either
    registered trademarks or trademarks of
    Microsoft Corporation in the United States
    and/or other countries.
    MP3/WMA groups and tracks are not played
    back as you expect.
    \ Playing order is determined when the groups
    and tracks were recorded. It depends on the
    writing application.
    The disc/USB device sound is discontinuous.
    \ The disc is scratched or dirty.
    \ MP3/WMA files have not been properly copied
    onto the USB device.
    Sounds from USB device are interrupted.
    \ Noise and static electricity may stop the sound.
    In this case, disconnect and connect the USB
    device again after turning off the unit.
    iPod Operations
    iPod does not play, but CONNECT” appears on
    the display.
    \ The iPod battery is low or exhausted. Charge the
    iPod battery.
    Radio Operations
    Hard to listen to broadcasts because of noise.
    \ The FM antenna is not properly extended and
    positioned.
    \ Electrostatic discharge from your body may
    cause noise. If this happens, turn off and on the
    unit again.
    Timer Operations
    Daily Timer does not work.
    \ The unit has been turned on when the on-time
    comes. Timer starts working only when the unit
    is turned off.
    If you are having a problem with your unit, check this
    list for a possible solution before calling for service.
    General
    Power does not come on.
    \ No power is supplied. Check the power cord
    connection or change the batteries.
    Adjustments or settings are suddenly canceled
    before you finish.
    \ There is a time limit. Repeat the procedure again.
    Unable to operate the unit or the unit does not
    work properly.
    \ The built-in microprocessor may malfunction due
    to external electrical interference.
    Unplug the power cord, then plug it back in.
    \ Batteries are exhausted. Change the batteries.
    Unable to operate the unit from the remote
    control.
    \ The path between the remote control and the
    remote sensor on the unit is blocked.
    \ The batteries are exhausted.
    No sound is heard.
    \ Headphones are connected.
    While the power is supplied using the batteries,
    sound from the speakers is distorted or too quiet.
    \ Batteries are exhausted. Change the batteries.
    Disc/USB Mass Storage Class Device
    Operations
    The disc/USB device does not play.
    \ The disc is placed upside down. Place the disc with
    the label side up.
    \ The disc is recorded with the packet writing (UDF
    file unit). It cannot be played. Check the files you
    want to play back.
    \ The USB device is not connected properly.
    To get the best performance of the unit, keep
    your discs and mechanism clean.
    Handling discs
    Remove the disc from its case by holding it
    at the edge while pressing the center hole
    lightly.
    Do not touch the shiny surface of the disc, or
    bend the disc.
    Put the disc back in its case after use.
    Be careful not to scratch the surface of the
    disc when placing it back in its case.
    Avoid exposure to direct sunlight,
    temperature extremes, and moisture.
    Cleaning discs
    Wipe the disc with a soft cloth in a straight
    line from center to edge.
    Cleaning the unit
    Stains should be wiped off with a soft cloth. If
    the unit is heavily stained, wipe it with a cloth
    soaked in water-diluted neutral detergent
    and wrung well, then wipe clean with a dry
    cloth.
    Since the unit may deteriorate in quality,
    become damaged or get its paint peeled off,
    be careful about the following:
    – DO NOT wipe it hard.
    – DO NOT wipe it with thinner or benzine.
    – DO NOT apply any volatile substance such
    as insecticides to it.
    – DO NOT allow any rubber or plastic to
    remain in contact for a long time.
    Cleaning the CD pickup lens
    Keep the CD pickup lens clean, or the sound
    may be degraded. Use a blower (available at a
    camera store, etc.) to blow dust off the lens.
    ABOUT DISC/FILE/iPod/DISPLAY
    The reflection factor of CD-RW is lower than that of
    other CDs, possibly causing CD-RW to take longer
    time to read.
    In this manual, “file and “track are interchangeably
    used for MP3/WMA operations.
    POWERED WOOFER CD SYSTEM
    RV-NB52B/RV-NB50
    Front view/Face
    Side view/Côté
    15 cm
    (5 15/16”)
    10 cm
    (3 15/16”)
    Caution: Proper Ventilation
    To avoid risk of electric shock and fire, and to prevent
    damage, locate the apparatus as follows:
    1 Front:
    No obstructions and open spacing.
    2 Sides/ Top/ Back:
    No obstructions should be placed in the areas shown by
    the dimensions below.
    3 Bottom:
    Place on the level surface. Maintain an adequate air path
    for ventilation by placing on a stand with a height of
    10 cm (3 15/16”) or more.
    Attention: Aération correcte
    Pour prévenir tout risque de décharge électrique ou
    d’incendie et éviter toute détérioration, installez l’appareil
    de la manière suivante:
    1 Avant:
    Bien dégagé de tout objet.
    2 Côtés/dessus/dessous:
    Assurez-vous que rien ne bloque les espaces indiqués sur
    le schéma ci-dessous.
    3 Dessous:
    Posez l’appareil sur une surface plane et horizontale.
    Veillez à ce que sa ventilation correcte puisse se faire en
    le plaçant sur un support d’au moins dix centimètres de
    hauteur.
    Thank you for purchasing a JVC product.
    Before operation, please read the instructions carefully.
    15 cm
    (5 15/16”)
    15 cm
    (5 15/16”)
    15 cm
    (5 15/16”)
    15 cm
    (5 15/16”)
    10 cm
    (3 15/16”)
    INSTRUCTIONS
    LVT2062-001B[J/C]
    0110YOMMDWBET
    EN
    ©2009 Victor Company of Japan, Limited
    For customer use:
    Enter below the Model No. and Serial No. which are
    located either on the rear, bottom or side of the
    cabinet. Retain this information for future reference.
    Model No.
    Serial No.
    REFERENCES
    Blower
    Lens
    Battery compartment R20 (SUM-1)/D(13D)
    (not supplied)
    To cars cigarette
    lighter socket
    (DC12V)
    Power cord
    (supplied)
    AC outlet
    R6(SUM-3)/AA(15F)
    (not supplied)
    0786
    34
    9
    521
    Car adapter (not supplied)
    RV-NB50[J_C].indd 1RV-NB50[J_C].indd 1 10.1.27 9:06:38 PM10.1.27 9:06:38 PM
JVC RV-NB50

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre JVC RV-NB50 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de JVC RV-NB50 responder adecuadamente a su pregunta.

Vea el manual de JVC RV-NB50 aquí, de forma gratuita. Este manual pertenece a la categoría Altavoces Dock y ha sido calificado por 1 personas con un promedio de 7. Este manual está disponible en los siguientes idiomas: Inglés. ¿Tiene alguna pregunta sobre JVC RV-NB50 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de JVC RV-NB50

General
Marca JVC
Modelo RV-NB50
Producto Altavoz Dock
EAN 4975769373121
Idioma Inglés
Tipo de archivo PDF
Audio
Cantidad de bandas en ecualizador 4
Convertidor de audio D/A 1-bit
Formatos de audio soportados MP3, WMA
Altavoces
Altavoces 4
Altavoces incorporados
Unidad de disco 80mm
Radio
Sintonizador digital
Bandas de radio soportadas FM
Tipos de medios
Reproducción de CD-RW
Reproducción de CD-R
Características
Reproducción MP3
Cantidad de estaciones predeterminadas 30
Tipo de dispositivo Reproductor de CD portátil
Color del producto Black, Grey
Exhibición
Pantalla LCD
Monitor con luz de fondo
Características de administración
Pistas programables 20
Temporizador de apagado
Mando a distancia
Batería
Tipo de batería R20 (SUM-1) / D (13D)
Control de energía
Numero de baterías soportadas 10
Requisitos de energía 230V, 50Hz; DC 15V
Otras características
Dimensiones (Ancho x Profundidad x Altura) 666 x 231 x 240mm
Peso y dimensiones
Peso 6800g

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más