Home
Pilas
LRP
1600UP

LRP 1600UP manual

(1)

If you are not using your battery pack for several days/weeks, under no circumstances it shall be
stored fully discharged. Storing of fully discharged NiMH batteries even for just a few days immediately
damages the cells.
We recommend to only
s
tore your NiMH battery packs with some capacity left in them. A common
way to do this is to partially charge the empty battery with 1C for 25 minutes. You can then store th
e
pack for at least 4 weeks at a temperature of 20°C without problems. Store the battery preferably in
a cool place.
Attention:
Storing NiMH batteries at higher temperatures increases the self-discharge rate of the bat-
teries. Therefore you have to recharge the battery more often when storing it at higher temperatures.
After a long storage period, the battery pack has to be discharged
with 5A
to a cut-off voltage of
5.4
V
(6 cells), 6.3V (7 cells), 7.2V (8 cells)
.
Pay attention, that the battery pack has cooled down completely
before beginning the charge.
LRP strongl
y
recommends
to not
use any Discharge trays or similar devices with the VTEC 2/3A-
1600UP cells.
We generally recommend a maximum charge current of 1C* and chargers, which are suited for NiMH
batteries. Our charger family of Pulsar, Quadra, Jet, Micro and NiMH-Charger are perfect for this appli-
cation.
Make sure not to overcharge your battery pack.
Charge up to a maximum cell temperature of 42ºC, when you are using a temperature cut-off charger.
We recommend the following settings, if you are using a charger of the LRP Pulsar family:
Cell type
Number
of cells
Charge
current
Delta Peak Trickle Mode
VTEC 2/3A-1600UP 7.2V
6
1
.6A
15mV
OFF
LIN
VTEC 2/3A-1600UP 8.4V
7
1
.6A
20mV
OFF
LIN
VTEC 2/3A-1600UP 9.6V
8
1
.6A
25
m
V
OFF
LIN
VTEC 2/3A-1400EP 7.2V
6
1.4A
15mV
OFF
LIN
VTEC 2/3A-1400EP 8.4V
7
1.4
A
20
mV
OFF
LIN
VTEC 2/3A-1400EP 9.6V
8
1.4A
25mV
OFF
LIN
Please note:
You can use your VTEC NiMH batteries up to 3-times per day, but they require at least 3
hours minimum rest between the cycles to fully cool down.
*
C=Nominal capacity of the battery.
E.
g. with a nominal capacity of 1600mAh (1.6Ah), the battery can
be charged wit
h a
max. current of 1.6
A
.
USER MANUAL
NiMH batteries
should never be stored completely empty. Always pay special attention, that your
battery is not completely discharged. Even if you use the battery once a week, the battery should
never be stored completely empty. Be sure to also check the information
, which is given in the section
„St
orage“
.
Best results will be obtained, when the battery pack gets
discharged with 5A
to a cut-off voltage of
5.4
V (6 cells), 6.3V (7 cells), 7.2V (8 cells)
, one
hour
before you need to start charging.
Pay attention,
that the battery back has cooled down completely before beginning the charge.
VTEC 2/3A-
1600UP
cells a
re high-performance
cells,
manufactured with the newest technology
available.
Discharging each cell below 1V over a longer period of time harms the battery and re-
duces the capaci
ty.
Ther
efore
we do not recommend the use of Discharge trays or similar devices
with the VTEC 2/3A-1600UP cells.
IMPORTANT:
Do not dead-short or deep-discharge the VTEC cells to 0V. Also do not use the common
light-bulbs without a cut-off or a monitoring device. This will immediately damage the cells irrever-
sible.
!
No toy. Not suitable for children under 14 years.
Keep the product out of the reach of children.
Pay close attention to the following points, as they can destroy the product and void your warran-
ty. Non-observance of these points can lead to property damage, personal and severe injuries!
•
Avoid incorrect connections or connections with reversed polarity of the product.
•
All wires and connections have to be well insulated. Short-circuits can possibly destroy the pro-
duct.
•
Always remove the battery from your product or disconnect the product from the power source, if
the product is not in use.
•
Do not throw away used batteries in the household garbage, but only give them to the collection
stations or dispose of them ar a special garbage depot.
•
Avoid soldering longer then 5 seconds per soldering joint while soldering batteries directly to prevent
damage to the batteries due to overheating. Use a high power soldering station with at least 60W
for soldering.
•
Always charge the battery outside of the product you want to use. The product could get damaged,
if a battery defect occurs.
•
Avoid short circuits, overcharging and reverse polarity of the battery or single cells. This can lead
to fire or explosion.
•
Never open a battery or a single cell.
•
Never leave the battery unattended while charging.
•
During charging, the battery has to be kept on a non-flammable, heat-resistant mat. Furthermore no
flammable or highly inflammable objects may be close to the battery.
•
Never exceed the maximum charge/discharge current, which is recommended by the LRP electronic
GmbH.
•
Under no circumstances a NiMH-battery shall be deep discharged.
•
The battery may never get in touch with fire, water or other liquids.
•
Only charge in a dry place.
•
Only use chargers and dischargers, which are specified for NiMH/NiCd-batteries by the manufactu-
rer. Never use chargers or dischargers, which are specified for LiPo-batteries!
•
Do not use different types of batteries and do not mix new and used batteries.
•
If individual cells in the battery pack heat up excessively, immediately stop the charging process.
•
The manufacturer can not be held responsible for damages, which are a result of non-observan-
ce of the warning notes and security advices.
All products from LRP electronic GmbH (hereinafter called “LRP”) are manufactured according to the
highest quality standards. LRP guarantees this product to be free from defects in materials or work-
manship for 90 days (non-european countris only) from the original date of purchase verified by sales
receipt. This limited warranty doesn’t cover defects, which are a result of misuse, improper mainte-
nance, outside interference or mechanical damage.
This especially applies on already used batteries
or batteries, which show signs of heavy usage. Damages or output losses due to improper handling
and/or overload are not a product fault. Signs of wear (loss of capacity) after intensive usage are also
no product fault.
To eliminate all other possibilities or improper handling, first check all other components in your model
and the trouble shooting guide, if available, before you send in this product for repair. If products are
sent in for repair, which do operate perfectly, we have to charge a service fee according to our pricelist.
The following points do also result in a service fee:
•
Original power plugs replaced with a NON reverse polarity protected power plug system
•
Send in the battery without power plugs
•
Removed or damaged original heatshrink
With sending in this product, the customer has to advise LRP if the product should be repaired in either
case. If there is neither a warranty nor guarantee claim, the inspection of the product and the repairs,
if necessary, in either case will be charged with a fee at the customers expense according to our price
list. A proof of purchase including date of purchase needs to be included. Otherwise, no warranty
can be granted. For quick repair- and return service, add your address and detailed description of the
malfunction.
If LRP no longer manufactures a returned defective product and we are unable to service it, we shall
provide you with a product that has at least the same value from one of the successor series.
The specifications like weight, size and others should be seen as guide values. Due to ongoing technical
improvements, which are done in the interest of the product, LRP does not take any responsibility for
the accuracy of these specs.
LRP-Distributor-Service:
•
Package your product carefully and include sales receipt and detailed description of malfunction.
•
Send parcel to your national LRP distributor.
•
Distributor repairs or exchanges the product.
•
Shipment back to you usually by COD (cash on delivery), but this is subject to your national LRP
distributor‘s general policy.
AA0051
5
© LRP electronic G
mbH 200
8
1. WARNING NOTES
Dear Customer,
t
hank you for your trust in this LRP product. By purchasing a
LRP VTEC NiMH-battery
,
you have chosen
a high-performance battery for your RC model.
Please read the following instructions
to ensure, that
your
LRP VTEC NiMH-battery
always works up to your full satisfaction.
NiMH-batteries need special treatment and care.
Please read the following instructions carefully
before you start using you
r
LRP VTEC NiMH-battery
. This user guide contains important notes for the
installation, the safety, the use and the maintenance of this product. Thus prote
cting yourself an
d
avoid damages
of
the product.
Proceed according to the user guide in order to understand your
LRP VTEC NiMH-battery
better.
Please
take your time as you will have much more joy with your product if you know it exactly.
This user manual shall be kept in a safe place. If another customer is using this product, this manual
has to be handed out together with it
.
2. CHARGING
3. DISCHARGING
5. STORAGE
REPAIR PROCEDURES /
LIMITED WARRANTY
LRP electronic GmbH
Wilhelm-Enssle-Str. 132-134
73630 Remshalden
Germany
i
nfo@LRP.cc
www.LRP.cc
VTEC 1600
LRP RACINGPACKS
HV² TREATED
ULTRA PERFORMANCE
4. SPECIFICATION
Type
Order#
Race
Configuration
# of
cells
Nominal
Voltage
Plug
VTEC 1600UP 7.2V NiMH Hump Pack
75610
Hump
6
7.2V
Micro
VTEC 1600UP
7.2V NiMH Side-by-Side Pack
75620
Side-by-Side
6
7.2V
Micro
VTEC 1600UP
7.2V NiMH Maverick Stick
75625
Stick
(for Maverick)
6
7.2V
Maverick
VTEC 1600UP
7.2V
NiMH Stickpack
75630
Stick
6
7.2V
Micro
VTEC 1600UP
8.4V
NiMH Stickpack
75635
Stick
7
8.4V
Micro
VTEC 1600UP
8.4V NiMH Hump Pack
75637
Hump
(for LRP Shark)
7
8.4V
Micro
VTEC 1600UP
9.6V NiMH Saddle Pack
75650
Saddle
(for Mini Inferno)
8
9.6V
Kyosho
Mini

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre LRP 1600UP o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de LRP 1600UP responder adecuadamente a su pregunta.

Acerca de LRP 1600UP

Vea el manual de LRP 1600UP aquí, de forma gratuita. Este manual pertenece a la categoría Pilas y ha sido calificado por 1 personas con un promedio de 8. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre LRP 1600UP o necesita ayuda? Haz tu pregunta aquí

Especificaciones de LRP 1600UP

General

Marca	LRP
Modelo	1600UP
Producto	Pila
EAN	4250068124149
Idioma	Engels
Tipo de archivo	PDF

Características

Tecnología de batería	Níquel-metal hidruro (NiMH)
Capacidad de batería	- mAh
Voltaje de la pila	7.2 V
Color del producto	Multicolor
Productos compatibles	-
Color del producto	Multicolor

Peso y dimensiones

Peso	- g
Peso	- g

Control de energía

Tecnología de batería	Níquel-metal hidruro (NiMH)
Voltaje de la pila	7.2 V

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.