1. Choose an appropriate corner location. The WS6 can be
mounted at any height in a corner.
2. Complete all wire and conduit runs prior to installation of
the housing.
REVISION DATE: 11-11-2010
Depending on the voltage being used, refer to one of the formulas
below to select the correct power supply for cameras connected
in parallel (positive to positive, negative to negative):
Total current for a 12 VDC system:
TOTAL CURRENT = (350mA x total number of cameras)
Total current for a 24 VAC system:
TOTAL CURRENT = (202mA x total number of cameras)
VOLTAGE CURRENT POWER
12 VDC 350mA 4.2W
24 VAC 202mA 4.8W
CABLE AND POWER GUIDELINES
(Detailed info on Page 11)
This chart shows the proper current needed for power supplies for
Warrior Series cameras. Use Class 2 Power only. Input voltage
must be between 12-28 VDC or 15-28 VAC.
81-IN5219 WARRIOR 6
WS6
INSTALLATION PROCEDURE
1. Using the security tool provided, loosen the (3) 10-32 security
fasteners and remove the face plate (Figure 1).
4. Feed the wiring through the conduit knockout. A clamp
connector is included should you desire to use it. Install
the connector so that the nut is on the outside of the housing.
Be sure the hole in the wall is large enough to accommodate
the nut. Tighten the nut securely, making sure that the screw
heads on the connector are in an easy to reach position,
then feed the wiring through the clamp connector.
5. Mount the back box to the wall using appropriate hardware
(not provided).
NOTE: If the clamp connector was used, tighten the screws
at this time. Make sure enough wire is inside
the back box to complete the wiring process.
2. Place the back box into position and mark the four mounting
holes (Figure 2).
3. If you're using the top conduit knockout (Figure 2) REMOVE
THE CAMERA AND BRACKET TO PREVENT DAMAGE.
If using one of the side conduit knockouts it's not necessary to
remove the camera and bracket; however, use caution.
Mounting
Holes
Figure 1
Top conduit knockout behind camera CAMERA MUST BE
REMOVED BEFORE USING
Mounting Holes
Figure 2
TABLE OF CONTENTS
Cable and Power Guidelines 1, 11
Installation Preparation 1
Installation Procedure 1
Wiring 2
Optional Warrior Test Monitor Cable 2
Camera Bracket Setup 2
Camera Focusing 3
Camera Settings 3
Completion of Installation 5
Window Guard™ Replacement 5
NVT Instructions 5
Warranty Information 7
Service and Safeguard Information 8
Troubleshooting 9
Whatsapp
Mail
Facebook
¿Necesita ayuda?
Número de preguntas: 0
¿Tiene alguna pregunta sobre Moog Videolarm WS6S-50NF-X2 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Moog Videolarm WS6S-50NF-X2 responder adecuadamente a su pregunta.
Acerca de Moog Videolarm WS6S-50NF-X2
Vea el manual de Moog Videolarm WS6S-50NF-X2 aquí, de forma gratuita. Este manual pertenece a la categoría Cámaras de vigilancia y ha sido calificado por 1 personas con un promedio de 7.5. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Moog Videolarm WS6S-50NF-X2 o necesita ayuda? Haz tu pregunta aquí
A continuación, encontrarás las preguntas más frecuentes sobre el Moog Videolarm WS6S-50NF-X2 .
¿Qué es un megapíxel?
El número de megapíxeles indica cuántos píxeles hay en el sensor. 1 megapíxel equivale a 1 millón de píxeles. Cuantos más píxeles, mayor será la calidad de imagen potencial.
Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.
PRODUCT INSTRUCTIONSINSTALLATION PREPARATIONINSTALLATION PREPARATION1. Choose an appropriate corner location. The WS6 can bemounted at any height in a corner.2. Complete all wire and conduit runs prior to installation ofthe housing.REVISION DATE: 11-11-2010Depending on the voltage being used, refer to one of the formulasbelow to select the correct power supply for cameras connectedin parallel (positive to positive, negative to negative):Total current for a 12 VDC system:TOTAL CURRENT = (350mA x total number of cameras)Total current for a 24 VAC system:TOTAL CURRENT = (202mA x total number of cameras)VOLTAGE CURRENT POWER12 VDC 350mA 4.2W24 VAC 202mA 4.8WCABLE AND POWER GUIDELINES(Detailed info on Page 11)This chart shows the proper current needed for power supplies forWarrior Series cameras. Use Class 2 Power only. Input voltagemust be between 12-28 VDC or 15-28 VAC.81-IN5219 WARRIOR 6WS6INSTALLATION PROCEDURE1. Using the security tool provided, loosen the (3) 10-32 securityfasteners and remove the face plate (Figure 1).4. Feed the wiring through the conduit knockout. A clampconnector is included should you desire to use it. Installthe connector so that the nut is on the outside of the housing.Be sure the hole in the wall is large enough to accommodatethe nut. Tighten the nut securely, making sure that the screwheads on the connector are in an easy to reach position,then feed the wiring through the clamp connector.5. Mount the back box to the wall using appropriate hardware(not provided).NOTE: If the clamp connector was used, tighten the screwsat this time. Make sure enough wire is insidethe back box to complete the wiring process.2. Place the back box into position and mark the four mountingholes (Figure 2).3. If you're using the top conduit knockout (Figure 2) REMOVETHE CAMERA AND BRACKET TO PREVENT DAMAGE.If using one of the side conduit knockouts it's not necessary toremove the camera and bracket; however, use caution.MountingHolesFigure 1Top conduit knockout behind camera CAMERA MUST BEREMOVED BEFORE USINGMounting HolesFigure 2TABLE OF CONTENTSCable and Power Guidelines 1, 11Installation Preparation 1Installation Procedure 1Wiring 2Optional Warrior Test Monitor Cable 2Camera Bracket Setup 2Camera Focusing 3Camera Settings 3Completion of Installation 5Window Guard™ Replacement 5NVT Instructions 5Warranty Information 7Service and Safeguard Information 8Troubleshooting 9
