5650-16-M-SC, NPort 5650-8-S-SC, and NPort 5650-16-S-SC.
NOTE
The wide temperature model does not support LCM display
panel
s or push buttons. Allofthe LCM descriptions below
apply only tostandard temperature models.
The front and rear panels are shown below:
Front panel of the NPort5600 Series
Rear panel of the NPort 5610/5630/5650 (AC Power)
Rear panel of the NPort 5650 (Fiber Model)
Rear panel of the NPort 5610 (DC Power)
Front panel of the NPort 5650-T Series
Reset Button—press the Reset button continuously for 5 sec to
load factory defaults: Use a pointed object to press the reset
button. Release the button after the Ready LED stops blinking.
LED Indicators on the Front Panel—the front panels of the
NPort 5600 have several LED indicators, as described in the
followingtable.
Name
Color
Function
Ready
Off
Power is off, or power error condition exists.
Red
Steady on:Power is on and the NPort is
booting up.
Blinking:Indicates an IP conflict, or DHCP or
BOOTP server did not respond properly.
Green
Steady on: Power is on and the NPort is
functioning normally.
Blinking:
The NPort has been located by NPort
Administrator’s Location function.
1-16
Orange
Serial port is receiving data.
Green
Serial port is transmitting data.
Off
No data is being transmitted or received
through the serial port.
LCM Display Panel—If the NPort is working properly, the LCM
panel will display a green color. The red Ready LED will also light
up, indicating that the NPort is receiving power. After the red
Ready LED turns green, youwill see a display similar to:
N
P
5
6
1
0
-
1
6
3
8
1
9
2
.
1
6
8
.
1
2
7
.
2
5
4
This is where
•NP5610-16is the NPort’s name
•38is the NPort’s serial number
•192.168.127.254is the NPort’s IP address
LCM Panel Operation—There are four buttons on the NPort
5600’s front panel. These buttons are used to operate the server’s
LCM panel. Going from left to right, the buttons are:
Button
Action
MENU
Activates the main menu, or returns to a lower level.
︿
Scrolls up through a list of items shown on the LCM
panel’s second line.
﹀
Scrolls down through a list of items shown on the LCM
panel’s second line.
SELSelects the option listed on the LCM panel’s second
line.
Detailed LCM Panel Operating instructions can be found on the
CD-ROM in the NPort 5600 Series User’s Manual.
Link Indicator on the rear panel of the NPort 5650 fiber
model—the rear panels of the NPort 5650have a link indicator, as
described in the following table.
LED Name
LED Color
LED Function
Link
Off
Fiber disconnected.
Green
Fiber connected; data nottransmitting.
Blinking
Fiber connected; data istransmitting.
4.Hardware Installation
STEP 1: After removing the NPort 5600 from the box, the first
thing you should do is attach the power adaptor.
STEP 2: Connecting the Power.
AC: Connect the NPort 5600’s 100-240 VAC power cord to the AC
connector. The “Ready” LED willshow a solid red color until the
system is ready, at which time it will change to agreen color.
DC: Connect the NPort 5610-16/8-48V’s power cord to the DC
connector, and then follow the steps given below:
Loosen the screws on the V+ and V- terminals of
the NPort 5610-8/16-48V’s terminal block.
Connect the power cord’s 48 VDC or -48 VDCwire
to the terminal block’s V+ terminal, and the power
cord’s DC Power Ground wire to the terminal block’s V- terminal,
and then tighten the terminal block screws. (Note: The NPort
5610-8/16-48V can still operate even if the 48V/-48V and DC
Power Ground are reversed.)
The “Ready” LED will show a solid red color until the system is
ready, at which time itwill change toa green color.
Grounding the NPort 5610-8/16-48V:
Grounding and wire routing help limit the effects of
noise due to electromagnetic interference (EMI).
Run the ground connection from the ground
screw to the grounding surface prior to
connecting devices. The Shielded Ground
(sometimes called Protected Ground) contact is
the second contact from the right of the 5-pin power terminal block
connector located on the rear panel of the NPort 5610-8/16-48V.
Connect the SG wire to the Earth ground.
STEP 3: Connect the NPort 5600 to a network. Use a standard
straight-through Ethernet cable to connect to a hub or switch.
When setting up or testing the NPort 5600, you might find it
convenient to connect directly to your computer’s Ethernet port. In
this case, use a cross-over Ethernet cable.
Whatsapp
Mail
Facebook
¿Necesita ayuda?
Número de preguntas: 0
¿Tiene alguna pregunta sobre Moxa NPort 5650-16-M-SC o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Moxa NPort 5650-16-M-SC responder adecuadamente a su pregunta.
Acerca de Moxa NPort 5650-16-M-SC
Vea el manual de Moxa NPort 5650-16-M-SC aquí, de forma gratuita. Este manual pertenece a la categoría Servidores y ha sido calificado por 1 personas con un promedio de 7.5. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Moxa NPort 5650-16-M-SC o necesita ayuda? Haz tu pregunta aquí
Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.
– 1 – – 2 – – 3 –P/N: 1802056000211NPort 5600 Series QuickInstallation GuideThird Edition, November 20101. OverviewWelcome to the Moxa NPort 5600 Series. The NPort 5610-8/16have 8 or 16 RS-232 ports, the NPort 5630-8/16 have 8 or 16RS-422/485 ports, and the NPort 5650-8/16 have 8 or 16RS-232/422/485 ports.2. Package ChecklistThe NPort 5600 package should contain the following items:• 1 8-port or 16-port serial device server• NPort Documentation & Software CD• NPort 5600 Quick Installation GuideOptional Accessories:• CBL-RJ45M9-150: 8-pin RJ45 to DB9 male cable, 150 cm• CBL-RJ45F9-150: 8-pin RJ45 to DB9 female cable, 150 cm• CBL-RJ45M25-150: 8-pin RJ45 to DB25 male cable, 150 cm• CBL-RJ45F25-150: 8-pin RJ45 to DB25 female cable, 150 cmNotify your sales representative if any of the above items ismissing or damaged.3. Hardware IntroductionThe NPort 5600 Series has includes the following models: NPort5610-8, NPort 5610-16, NPort 5610-8-48V, NPort 5610-16-48V,NPort 5630-8, NPort 5630-16, NPort 5650-8, NPort 5650-8-T,NPort 5650-16, NPort 5650-16-T, NPort 5650-8-M-SC, NPort5650-16-M-SC, NPort 5650-8-S-SC, and NPort 5650-16-S-SC.NOTEThe wide temperature model does not support LCM displaypanels or push buttons. All of the LCM descriptions belowapply only to standard temperature models.The front and rear panels are shown below:Front panel of the NPort 5600 SeriesRear panel of the NPort 5610/5630/5650 (AC Power)Rear panel of the NPort 5650 (Fiber Model)Rear panel of the NPort 5610 (DC Power)Front panel of the NPort 5650-T SeriesReset Button—press the Reset button continuously for 5 sec toload factory defaults: Use a pointed object to press the resetbutton. Release the button after the Ready LED stops blinking.LED Indicators on the Front Panel—the front panels of theNPort 5600 have several LED indicators, as described in thefollowing table.NameColorFunctionReadyOffPower is off, or power error condition exists.RedSteady on: Power is on and the NPort isbooting up.Blinking: Indicates an IP conflict, or DHCP orBOOTP server did not respond properly.GreenSteady on: Power is on and the NPort isfunctioning normally.Blinking:The NPort has been located by NPortAdministrator’s Location function.1-16OrangeSerial port is receiving data.GreenSerial port is transmitting data.OffNo data is being transmitted or receivedthrough the serial port.LCM Display Panel—If the NPort is working properly, the LCMpanel will display a green color. The red Ready LED will also lightup, indicating that the NPort is receiving power. After the redReady LED turns green, you will see a display similar to:NP5610-1638192.168.127.254This is where• NP5610-16 is the NPort’s name• 38 is the NPort’s serial number• 192.168.127.254 is the NPort’s IP addressLCM Panel Operation—There are four buttons on the NPort5600’s front panel. These buttons are used to operate the server’sLCM panel. Going from left to right, the buttons are:ButtonActionMENUActivates the main menu, or returns to a lower level.︿Scrolls up through a list of items shown on the LCMpanel’s second line.﹀Scrolls down through a list of items shown on the LCMpanel’s second line.SEL Selects the option listed on the LCM panel’s secondline.Detailed LCM Panel Operating instructions can be found on theCD-ROM in the NPort 5600 Series User’s Manual.Link Indicator on the rear panel of the NPort 5650 fibermodel—the rear panels of the NPort 5650 have a link indicator, asdescribed in the following table.LED NameLED ColorLED FunctionLinkOffFiber disconnected.GreenFiber connected; data not transmitting.BlinkingFiber connected; data is transmitting.4. Hardware InstallationSTEP 1: After removing the NPort 5600 from the box, the firstthing you should do is attach the power adaptor.STEP 2: Connecting the Power.AC: Connect the NPort 5600’s 100-240 VAC power cord to the ACconnector. The “Ready” LED will show a solid red color until thesystem is ready, at which time it will change to a green color.DC: Connect the NPort 5610-16/8-48V’s power cord to the DCconnector, and then follow the steps given below:Loosen the screws on the V+ and V- terminals ofthe NPort 5610-8/16-48V’s terminal block.Connect the power cord’s 48 VDC or -48 VDC wireto the terminal block’s V+ terminal, and the powercord’s DC Power Ground wire to the terminal block’s V- terminal,and then tighten the terminal block screws. (Note: The NPort5610-8/16-48V can still operate even if the 48V/-48V and DCPower Ground are reversed.)The “Ready” LED will show a solid red color until the system isready, at which time it will change to a green color.Grounding the NPort 5610-8/16-48V:Grounding and wire routing help limit the effects ofnoise due to electromagnetic interference (EMI).Run the ground connection from the groundscrew to the grounding surface prior toconnecting devices. The Shielded Ground(sometimes called Protected Ground) contact isthe second contact from the right of the 5-pin power terminal blockconnector located on the rear panel of the NPort 5610-8/16-48V.Connect the SG wire to the Earth ground.STEP 3: Connect the NPort 5600 to a network. Use a standardstraight-through Ethernet cable to connect to a hub or switch.When setting up or testing the NPort 5600, you might find itconvenient to connect directly to your computer’s Ethernet port. Inthis case, use a cross-over Ethernet cable.
