Oregon Scientific RMR682

Oregon Scientific RMR682 manual

(1)
  • Wireless Indoor / Outdoor Thermometer
    with Self-Setting Atomic Clock
    Model: RMR682A
    USER MANUAL
    INTRODUCTION
    Thank you for selecting the Oregon Scientific Wireless
    Indoor / Outdoor Thermometer with Self-Setting Atomic
    Clock (RMR682A). The main unit can support up to 3
    sensors. To purchase additional sensors, please contact
    your local retailer.
    NOTE Please keep this manual handy as you use your new
    product. It contains practical step-by-step instructions, as
    well as technical specifications and warnings you should
    know about.
    OVERVIEW
    FRONT VIEW
    1. Channel number and sensor reception status
    2. Sensor low battery warning
    3. Maximum / minimum outdoor temperature reading
    4. Indoor temperature display icon
    5. Main unit low battery warning
    6. Maximum / minimum indoor temperature reading
    7. Alarm is set
    8. 12-hour clock
    9. Alarm is displayed
    10. Radio-controlled clock reception icon
    11. Hi / lo alarm is displayed
    12. Outdoor temperature trend icon
    13. Ice warning is active
    14. Outdoor temperature reading
    15. Indoor temperature trend icon
    16. Indoor temperature reading
    17. US time zones
    18. Time, alarm and date
    BACK VIEW
    1. MEM: View current, maximum and minimum
    temperature
    2. TEMP HI / LO : Change settings or enable /
    disable hi or lo temperature alarm for channel 1
    3. / : Increase / decrease setting; activate /
    deactivate clock reception signal
    4. CHANNEL: Switch remote sensor display
    5. MODE: Change settings / display
    6. ALARM: View alarm status; set alarm
    7. Battery compartment
    8. ZONE: Toggle between the 4 US time zones
    9. °C / °F: Select temperature unit °C / °F
    10. RESET: Reset unit to default settings
    REMOTE SENSOR (THN122N)
    1. LED status
    indicator: Blinks red
    during data
    transmission
    2. Ventilation duct
    GETTING STARTED
    POWER
    Insert batteries before first use, matching the polarity (+
    and -).
    NOTE Install batteries in the remote sensor before the
    main unit. Press RESET after each battery change. Do
    not use rechargeable batteries. We recommend that you
    use alkaline batteries with this product for longer usage
    and lithium batteries in temperatures below freezing.
    shows when batteries are low.
    UNIT LOCATION
    Main Indoor temperature area
    Remote Outdoor temperature area
    REMOTE SENSOR
    The sensor collects temperature readings approx. every
    40 seconds and sends them to the main unit. The main
    unit can collect data from up to 3 sensors.
    To set up the sensor:
    1. Remove the screws from the battery door.
    2. Insert the batteries, matching the polarity (+ / -).
    3. Select a channel. Make sure you use a different
    channel for each sensor.
    4. Place the sensor near the main unit. Press RESET
    on the sensor.
    5. Simultaneously press CHANNEL and MEM on the
    main unit to initiate signal sending between the
    sensor and main unit.
    6. Close the battery door and secure the screws.
    7. Place the sensor in the desired location using the
    table stand or wall mount.
    For best results:
    Place the sensor out of direct sunlight and moisture.
    Do not place the sensor more than 30 meters
    (100 feet) from the main (indoor) unit.
    Position the sensor so that it faces the main (indoor)
    unit, minimizing obstructions such as doors,
    walls, and furniture.
    Place the sensor in a location with a clear view to
    the sky, away from metallic or electronic objects.
    Position the sensor close to the main unit during
    cold winter months as below-freezing temperatures
    may affect battery performance and signal
    transmission.
    The transmission range may vary depending on many
    factors. You may need to experiment with various locations
    to get the best results.
    Standard Alkaline batteries contain significant amounts of
    water. Because of this they will freeze in low temperatures
    of approximately -12°C (10°F). Disposable Lithium batteries
    have a much lower threshold for temperature with an
    estimated freezing range of below -40°C (-40°F).
    Wireless ranges can be impacted by a variety of factors
    such as extremely cold temperatures. Extreme cold may
    temporarily reduce the effective range between the sensor
    and the base station. If the unit’s performance fails due to
    low temperature, the unit will resume proper functioning
    as the temperature rises to within the normal temperature
    range (i.e. no permanent damage will occur to the unit due
    to low temperatures).
    SENSOR DATA TRANSMISSION
    Data is sent from the sensor(s) every 40 seconds. The
    reception icon in the outdoor temperature area shows the
    status.
    ICON DESCRIPTION
    Main unit is searching for the
    sensor(s)
    A channel has been found
    Sensor 1 is sending data
    The sensor cannot be found.
    Search for the sensor or check
    batteries
    To search for a sensor:
    Simultaneously, press and hold
    MEM and CHANNEL for
    2 seconds.
    NOTE If the sensor is still not found, check the batteries,
    obstructions, and remote unit location.
    CLOCK
    CLOCK RECEPTION
    This product is designed to synchronize its date and time
    automatically once it is within range of the WWVB-60
    signal from the atomic clock in Boulder, Colorado.
    The sensor collects the radio signals whenever it is within
    1500 km (932 miles) of a signal.
    NOTE Initial reception takes 2-10 minutes for first set up or
    when RESET is pressed. Once complete, the reception icon
    will stop blinking. If the signal is weak, it can take up to 24
    hours to get a valid signal.
    RECEPTION SIGNAL
    STRONG WEAK NO SIGNAL
    To enable and force a signal search:
    Press and hold for 2 seconds.
    To disable the signal reception:
    Press and hold for 2 seconds.
    flashes when it is enabled.
    SET CLOCK
    To manually set the clock make sure the clock signal
    reception is disabled.
    To manually set the clock:
    1. Press and hold
    MODE for 2 seconds.
    2. Press and to change the settings.
    3. Press
    MODE to confirm.
    1
    2
    3
    4
    5
    6
    7
    9
    8
    10
    11
    12
    13
    14
    15
    16
    17
    18
    3
    1
    2
    8
    9
    10
    4
    5
    6
    7
    1
    2
    3
    4
    1
    2
    1. Wall mount hole
    2. RESET hole
    3. CHANNEL switch
    4. Battery compartment
    and - -.-(Outdoor
    temperature area)
    TM
    RMR682A_EN.indd 1 3/14/06 12:06:06 PM
Oregon Scientific RMR682

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Oregon Scientific RMR682 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Oregon Scientific RMR682 responder adecuadamente a su pregunta.

Vea el manual de Oregon Scientific RMR682 aquí, de forma gratuita. Este manual pertenece a la categoría Relojes y ha sido calificado por 1 personas con un promedio de 9.7. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Oregon Scientific RMR682 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Oregon Scientific RMR682

General
Marca Oregon Scientific
Modelo RMR682
Producto reloj
Idioma Engels
Tipo de archivo PDF
Peso y dimensiones
Ancho 107 mm
Profundidad 87 mm
Altura 56 mm
Peso 134 g
Detalles técnicos
Tipo Reloj de sobremesa digital
Factor de forma Plaza
Color del producto Blanco
Alarma Si
Termómetro Si
Calendario Si
Contenido del embalaje
Cantidad por paquete 1 pieza(s)
Control de energía
Tipo de batería AAA
Numero de baterías soportadas 4
Exhibición
Tipo de visualizador LCD

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2021 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más