OSD Audio Speaker Selector 12

OSD Audio Speaker Selector 12 manual

(1)
  • TSM8/ TSM12
    Autoformer Based Speaker Selector
    Instruction Manual
    AUDIO
    OSD
    Thank you for giving OSD AUDIO the chance to earn your business! We are condent you will nd that OSD oers an outstanding combination of performance
    and value in everything we make. To ensure you get the most out of your new TSM8/ TSM12, please take a moment to read this manual before you get started.
    OSD Audio • 1405 Pioneer St • Brea • CA • 92821 • www.osdaudio.com • Tel (562) 697-2600 • Fax (562) 697-2668
    1. Connections
    To connect the amplifiers/receivers to the speaker selector, remove the AMP A/B connector by firmly pulling it out of its 8-pole socket. Strip 1/4” of insulation from the end
    of each wire. Tightly twist the end of each wire until no frayed ends remain. Insert each wire into the appropriate hole on the removeable terminals (matching up the
    polarity). Use a small screwdriver to tighten each wire into the AMP A/B connector. Insert the connector plug into the socket and lock in place . Be sure not to reverse
    these connections or the TSM12 /TSM8 will not function properly. Follow the same procedure to connect each pair of speakers to the appropriate speaker connector terminal,
    observing proper channel and polarity. If external volume controls are used, connect speaker wire from the appropriate speaker connector on the TSM12/ TSM8 to the volume
    control input. Speaker connections can support multiple speaker pairs wired in parallel or series, provided their combined impedance is a minimum of 4 ohms.
    2. Operation
    To ensure safe operation of the amplifier, an impedance level must first be selected using the rotary switch labeled speaker pair located on the rear of the unit. This switch should
    be set to the total number of speaker pairs being connected
    to the unit. Set the switch based on the following conditions:
    If the amplifier and the speakers are both 4 ohm or 8 ohm, set the rotary switch to the number of pair of speakers connected to the TSM12 /TSM8.
    If the amplifier is 8 ohm and the speakers are 4 ohm, set the rotary switch to TWICE the number of pair of speakers connected to TSM12 /TSM.8
    If the amplifier is 4 ohms and the speakers are 8 ohms, set the rotary switch to HALF the number of pair of speakers connected to the TSM12 /TSM8.
    After setting the proper impedance level, the speakers can be turned on and off in any combination.
    Switch between the A and B amplifiers, push the AMP A / AMP B button located on the front panel.
    3. Setting System Volume
    It is important to properly adjust an impedance-matching system to avoid distortion or DC clipping (DC voltage will be produced from an amplifier that is overworked or that has an
    improper load). These can cause an amplifier/receiver to go into protection, and can cause autoformers on volume controls to heat up, damaging system components. To set up
    the system, the amplifier/receiver volume should be at its lowest setting, and the in-wall/selector volume control should be at the highest setting. Slowly adjust the
    amplifier/receiver volume to a level that is acceptable for the amplifier to produce without clipping.
    100 Watts per channels RMS continuous
    200 Watts per channel average
    300 Watts per channel peak
    17” x 7.1” x 2.9”
    Up to 14 Gauge wire
    2 Years
    Listening Zones:
    8 (TSM8)
    12 (TSM12)
    Power:
    Dimensions: L x W x H:
    Cable Gauge:
    Warranty:
    100 Watts per channels RMS continuous
    200 Watts per channel average
    300 Watts per channel peak
    17” x 7.1” x 2.9”
    Up to 14 Gauge wire
    2 Years
    AUDIO
    OSD
    7-8
    6
    5
    3-4
    2
    1
    Number of
    Speaker Pair
    AMPLIFIERS
    SPEAKERS
    AMP A
    AMP B
    AMPLIFIERS
    PAIR1PAIR2
    PAIR3
    PAIR4
    PAIR5PAIR6
    PAIR7
    PAIR8
OSD Audio Speaker Selector 12

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre OSD Audio Speaker Selector 12 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de OSD Audio Speaker Selector 12 responder adecuadamente a su pregunta.

Vea el manual de OSD Audio Speaker Selector 12 aquí, de forma gratuita. Este manual pertenece a la categoría Interruptores y ha sido calificado por 1 personas con un promedio de 7.6. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre OSD Audio Speaker Selector 12 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de OSD Audio Speaker Selector 12

General
Marca OSD Audio
Modelo Speaker Selector 12
Producto Interruptor
Idioma Engels
Tipo de archivo PDF
Audio
Canales de entrada de audio 2
Canales de salida de audio 8 canales
Detalles técnicos
Potencia mínima por canal 100 W
Potencia máxima por canal 300 W
Tipo de control Botones
Color del producto Negro
Peso y dimensiones
Ancho 431.8 mm
Profundidad 209.55 mm
Altura 73 mm
Peso 4990 g

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2021 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más