Panasonic TY-LA1000

Panasonic TY-LA1000 manual

(1)
  • WARNING:
    The lamp may be hot. Be careful when handling.
    CAUTION:
    High-pressure lamp may explode if improperly
    handled.
    Danger of injury due to glass fragments.
    Lamp replacement procedure
    1
    Turn power off, wait until power
    indicator stops blinking red, then
    unplug the power cord from the wall
    outlet and con rm that the area around
    the lamp unit has cooled down.
    Please wait more than one hour for lamp
    replacement.
    [If you need to replace the lamp more urgently]
    The Projection display has a forced cooling
    feature. After the POWER button is turned OFF,
    and during the rst minute of the normal cooling
    fan operation, press the VOL+ button on the
    projection display and button on the remote
    control at same time for more than 5 seconds. The
    cooling fan operates for about 10 minutes. The
    LAMP indicator ashes red 5 times every 5
    seconds.
    POWER
    button
    /POWER
    indicator
    Lamp Re place ment
    3
    Loosen the Lamp cover screw.
    First read caution and warn ing labels
    on lamp cover. Then, loosen the lamp
    cover screw by using a screwdriver.
    Lamp unit screw
    Screwdriver
    4
    Loosen the lamp unit screw with a
    screwdriver. Then, grasp the lamp unit
    as shown in the diagram, and slowly
    remove from the projection display.
    Do not drop, as the impact of dropping may cause
    the lamp to explode.
    2
    Remove the Front cover. Place your
    ngertips under the Front cover and
    pull it from the projection display.
    Lamp unit handle
    Lamp cover handle
    6
    Replace the Lamp unit and cover
    screws. Tighten the lamp unit/cover
    screw with a screwdriver.
    Properly dispose of old lamp.
    Attach the lamp unit and lamp unit housing door
    securely. If the lamp unit and lamp unit housing
    door are not attached securely, the protective
    circuit will be activated and the lamp will not turn
    on.
    Note
    7
    Replace the Front cover.
    5
    Insert the new lamp unit being careful
    of the insertion direction.
    Press on the arrow mark making sure insertion is
    done correctly.
    Lamp time reset procedure
    1
    Be sure the power cord is plugged into
    a properly grounded wall outlet. Then,
    press the POWER button on the projection
    display or the remote control to turn the
    unit on.
    Warning:
    Perform lamp time reset only when the lamp has
    been replaced.
    When lamp time reset is nished, the LAMP
    indicator goes out.
    Note
    After lamp re place ment,
    follow the pro ce dure below
    3
    When reset
    procedure is
    complete, the
    screen on the right
    will appear.
    and
    Lamp cover screw
    LAMP indicator
    2
    While pressing the VOL- button on
    the projection display, hold down the
    PIP button on the remote control at
    same time for more than 5 seconds.
    LSQC0334
    CAUTION:
    [Under no circumstance should you touch the
    actual bulb.]
    At this high operating temperature the natural oil
    on your nger can cause the glass to weaken
    where touched and the bulb can crack or explode.
    This product has a High Intensity Discharge (HID)
    lamp that contains a small amount of mercury.
    Disposal of these materials may be regulated in
    your community due to environmental
    considerations.
    For disposal or recycling information please contact
    your local authorities, or the Electronics Industries
    Alliance: <http://www.eiae.org.>
    CAUTION:
    Because of the possibility of injury, strictly follow the
    replacement procedure below.
    LAMP TIME WAS
    RESET TO 0.
    EXIT
    Front cover
Panasonic TY-LA1000

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Panasonic TY-LA1000 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Panasonic TY-LA1000 responder adecuadamente a su pregunta.

Vea el manual de Panasonic TY-LA1000 aquí, de forma gratuita. Este manual pertenece a la categoría Lámparas y ha sido calificado por 1 personas con un promedio de 9. Este manual está disponible en los siguientes idiomas: Engels. ¿Tiene alguna pregunta sobre Panasonic TY-LA1000 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Panasonic TY-LA1000

General
Marca Panasonic
Modelo TY-LA1000
Producto lámpara
EAN 37988974993, 379889749936, 842740007198
Idioma Engels
Tipo de archivo PDF
Características
Marca compatible Panasonic
Compatibilidad PT43LC14, PT43LCX64, PT44LCX65, PT50LC13, PT50LC14, PT50LCX63, PT50LCX64, PT52LCX65, PT60LC13, PT60LC14, PT60LCX63, PT60LCX64, PT61LCX65
Potencia de bombilla - W
Peso y dimensiones
Ancho 178 mm
Profundidad 114 mm
Altura 140 mm
Peso 839 g

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2021 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más