Roland SH-01A

Roland SH-01A manual

(1)
  • English
    Owner’s ManualSOUND MODULE
    SH-01A
    Copyright © 2017 ROLAND CORPORATION
    In order to use this device correctly, please carefully read “USING THE UNIT SAFELY and “IMPORTANT NOTES (the Leaflet “USING THE UNIT SAFELY) before use.
    After reading, keep these instructions at hand for immediate reference.
    Introduction
    The SH-01A is a sound module that can be used in conjunction with the K-25m keyboard unit
    (sold separately). The sound can be heard through the built-in speakers.
    * The SH-01A can operate on batteries or on USB bus power. If you are using batteries, insert
    four AA batteries, making sure that the batteries are oriented correctly.
    * If you handle batteries improperly, you risk explosion and uid leakage. Make sure that
    you carefully observe all of the items related to batteries that are listed in “USING THE UNIT
    SAFELY and “IMPORTANT NOTES” (leaet “USING THE UNIT SAFELY”).
    * When turning the unit over, be careful so as to protect the buttons and knobs from damage.
    Also, handle the unit carefully; do not drop it.
    * When the batteries run low, the indication
    Bt. Lo
    appears in the display. Replace the
    battery as soon as possible.
    Using the SH-01A in conjunction with the DK-01 Boutique Dock (sold separately)
    &
    For installation / removal / angle adjustment, refer to the DK-01’s Owners Manual.
    Using the SH-01A in conjunction with the K-25m keyboard unit (sold separately)
    &
    For installation / removal / angle adjustment, refer to the K-25ms Owner’s Manual.
    Playing the SH-01A via MIDI or USB
    You can also play the SH-01A via USB. For details, refer to “Connecting Your Equipment.
    Connecting Your Equipment
    * To prevent malfunction and equipment failure, always turn down the volume, and turn o all
    the units before making any connections.
    A B C D E F
    G
    A
    Micro USB ( ) port
    Use a commercially available USB 2.0 cable (A-micro B)
    to connect this port to your computer. It can be used to
    transfer USB MIDI and USB audio data. You must install the
    USB driver when connecting the SH-01A to your computer. Download the USB driver from the
    Roland website. For details, refer to Readme.htm which is included in the download.
    &
    https://www.roland.com/support/
    * Do not use a micro USB cable that is designed only for charging a device. Charge-only cables
    cannot transmit data.
    B
    [VOLUME] knob
    Adjusts the volume.
    C
    PHONES jack
    Connect headphones (sold separately) here.
    D
    OUTPUT jack
    Connect this jack to your amp or monitor speakers.
    E
    MIX IN jack
    This is the audio input jack. Sound from the connected device is output from the OUTPUT jack
    and PHONES jack.
    F
    MIDI jack
    You can play the SH-01A by connecting a MIDI device via a
    commercially available MIDI cable.
    Turning the SH-01A On
    G
    [POWER] switch
    This turns the power on/o.
    * After you’ve made connections correctly, be sure to turn on the power in the order of the
    SH-01A rst, and then the connected system. Powering-on in the incorrect order may cause
    malfunctions or damage. When turning the power o, power-o the connected system rst,
    and then the SH-01A.
    * Before turning the unit on/o, always be sure to turn the volume down. Even with the volume
    turned down, you might hear some sound when switching the unit on/o. However, this is
    normal and does not indicate a malfunction.
    Returning to the Factory Settings (Factory Reset)
    Here’s how to return the SH-01A to its factory-set state.
    1.
    While holding down the [2] button, turn on the power.
    The [MENU] button blinks.
    If you decide to cancel the factory reset, turn o the power.
    2.
    Press the [MENU] button to execute the factory reset.
    3.
    When all buttons blink, turn the SH-01As power o, then on again.
    Data Backup/Restore
    Backup
    1.
    Connect your computer to the SH-01As USB port via USB cable.
    2.
    While holding down the [MENU] button, turn on the power.
    3.
    Open the “SH-01A” drive on your computer.
    The backup les are located in the “BACKUP” folder of the “SH-01A drive.
    4.
    Copy the backup les into your computer.
    5.
    After copying is completed, eject the USB drive.
    Windows 10/8/7
    Right-click on the “SH-01A icon and execute “Eject.
    Mac OS
    Drag the “SH-01A” icon to the Trash icon in the Dock.
    6.
    Turn the SH-01A power o.
    Restore
    1.
    As described in the procedure for “Backup” Step 1–3, open the “SH-01A drive on your
    computer.
    2.
    Copy the SH-01A backup les into the “RESTORE” folder of the “SH-01A drive.
    3.
    After copying is completed, eject the USB drive and then press the [MENU] button.
    4.
    After the LEDs have completely stopped blinking, turn o the power.
    Panel Descriptions
    2 3 4 5 6 7 8
    1
    1
    Common section
    Controller Explanation
    BENDER [VCO]
    [VCF] sliders
    Specify the amount of pitch change (VCO) and the amount of filter change
    (VCF) that occurs when you perform pitch bend operations.
    MOD [LFO] slider
    Specifies the depth of the effect produced by the LFO when it is used for
    modulation.
    [PORTAMENTO]
    knob
    Adjusts the time taken by the pitch change.
    PORTAMENTO
    switch
    OFF: Portamento is not applied.
    AUTO: Portamento is applied only when you play legato.
    ON: Portamento is always applied.
    [MENU] button Select a menu item.
    Display
    Indicates the tempo or step.
    When you’re selecting a patch or pattern, this indicates the bank and number.
    The decimal point of the first digit indicates that the pattern is being edited.
    The decimal point of the fourth digit indicates that the sound is being edited.
    TRANSPOSE
    switch
    Shifts the pitch up or down by one octave.
    L: The pitch is one octave lower.
    M: The pitch is not changed.
    H: The pitch is one octave higher.
    Controller Explanation
    [TEMPO/VALUE]
    knob
    Adjusts the tempo.
    When selecting a patch, this knob switches banks.
    Hold down the SEQUENCER [LOAD] button and turn this knob to adjust the
    SHUFFLE value.
    Hold down one of the ARPEGGIO buttons and turn this knob to change the
    SCALE value.
    [TUNE] knob Adjusts the pitch of the entire SH-01A.
    SEQUENCER
    [LOAD] button
    Activates sequencer write mode.
    SEQUENCER
    [PLAY] button
    Starts the sequencer.
    ARPEGGIO
    [DOWN] button
    Selects TYPE “DOWN” and turns the arpeggio on.
    ARPEGGIO
    [U&D] button
    Selects TYPE “U&D and turns the arpeggio on.
    ARPEGGIO
    [UP] button
    Selects TYPE “UP and turns the arpeggio on.
    [HOLD/LEGATO]
    button
    Turns HOLD on.
    If ARPEGGIO is on, the arpeggio continues playing even after you release the
    keyboard.
    [KEY TRANSPOSE/
    REST] button
    Transposes the pitch. This lets you perform in a different key without changing
    your fingering.
    CV/GATE OUT
    jacks
    You can connect an analog synthesizer equipped with CV/GATE input jacks,
    and control its note on/off or pitch.
    EXT CLK IN jack
    The arpeggiator or sequencer can play in synchronization with a clock signal
    that is input from this jack.
    2
    Ribbon controllers (C1/C2)
    These are touch-type ribbon controllers. C1 (left) is pitch bend, and C2 (right) is modulation.
    You can select either one octave or two octaves as the octave range of the arpeggiator.
    While you hold down the [DOWN] [U&D] [UP] buttons, the LED indication of C1 changes.
    Operation Explanation
    Tap the lower half of C1 To select one octave (the bottom LED blinks).
    Tap the upper half of C1 To select two octaves (the top LED blinks).
    * If a K-25m keyboard unit, USB, or MIDI are not connected, touching the C1 controller plays a
    preview sound.
    3
    LFO
    Here you can create cyclic change (modulation) in the sound.
    Controller Explanation
    [RATE] slider Determines the speed of the LFO modulation.
    Wave knob
    Selects the LFO waveform.
    (Sawtooth wave), (Reverse sawtooth wave),
    (Triangle wave), (Square wave), RANDOM, NOISE
    4
    VCO
    Selects the waveform that determines the character of the sound, and determines the pitch.
    Controller Explanation
    [MOD] slider
    Adjusts the depth to which the
    3
    LFO modulate the VCO.
    [RANGE] knob Specifies the octave of the oscillator.
    [PULSE WIDTH]
    slider/switch
    When the switch is set to “MAN” (MANUAL):
    The slider adjusts the pulse width value.
    When the switch is set to “LFO” or “ENV”:
    The slider adjusts the depth of modulation.
    What is pulse width?
    Pulse width is a value indicating the percentage occupied by the upper
    segment of a square wave. If the upper and lower segments are unequal,
    the result is an asymmetrical square wave.
    5
    SOURCE MIXER
    This mixer adjusts the volumes of the VCO, SUB OSC, and NOISE.
    Controller Explanation
    [
    ] slider Square wave level
    [
    ] slider Sawtooth wave level
    [SUB OSC] slider Sub oscillator level
    [SUB OSC] switch
    Specifies the SUB OSC type.
    1 OCT DOWN: One octave lower
    2 OCT DOWN: Two octaves lower
    2 OCT DOWN: Two octaves lower (narrow pulse width)
    [NOISE] slider Noise level
    6
    VCF
    These settings determine the brightness and thickness of the sound. Here you can also specify
    the time-varying change (envelope) for the lter.
    Controller Explanation
    [FREQ] slider Specifies the cutoff frequency of the low-pass filter.
    [RES] slider Resonance boosts the sound in the region of the filter’s cutoff frequency.
    [ENV] slider
    Adjusts the depth of control when using the envelope generator signal to
    control the VCF’s cutoff frequency.
    [MOD] slider
    Adjusts the depth of control when using the modulator signal to control the
    VCF’s cutoff frequency.
    [KYBD] slider Allows the filter cutoff frequency to vary according to the key that you play.
    7
    VCA
    Here you can create time-varying change (envelope) for the volume.
    Controller Explanation
    [ENV/GATE] switch
    ENV: The note is sounded according to the envelope specified by
    the ADSR settings.
    GATE: The note sounds at a fixed volume only while the key is held
    down.
    8
    ENV
    These settings specify the envelope.
    Controller Explanation
    [A] slider Attack time
    [D] slider Decay time
    [S] slider Sustain level
    [R] slider Release time
    [GATE/TRIG] switch
    Specifies what will trigger the envelopes attack.
    GATE+TRIG: The envelope attacks each time a key is pressed.
    LFO: When a key is held down, the envelope repeatedly attacks at
    each cycle of the LFO.
    GATE: The envelope attacks each time a key is pressed from a state of
    no keys being held. The envelope does not attack when notes
    are played legato.
    Selecting/Saving Patches (Sounds)
    Patch select mode
    1.
    Press the [MENU] button.
    2.
    Press the [1] button.
    Controller Explanation
    [VALUE] knob Switches banks.
    [1]–[8] button Switches patches.
    [1]–[8] buttons
    (Long-press)
    Writes the patch.
    [MENU] button Selects sequencer mode (normally).
    Manual mode
    1.
    Press the [MENU] button.
    2.
    Press the [8] button.
    Switches the patch to Manual.
    SH-01AMIDI keyboard
    MIDI INMIDI OUT
Roland SH-01A

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Roland SH-01A o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Roland SH-01A responder adecuadamente a su pregunta.

Vea el manual de Roland SH-01A aquí, de forma gratuita. Este manual pertenece a la categoría Sintetizadores y ha sido calificado por 1 personas con un promedio de 6. Este manual está disponible en los siguientes idiomas: Inglés. ¿Tiene alguna pregunta sobre Roland SH-01A o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Roland SH-01A

General
Marca Roland
Modelo SH-01A
Producto Sintetizador
EAN 4957054511456
Idioma Inglés
Tipo de archivo PDF
Características
Tipo de producto Sintetizador digital
Teclado, cantidad de teclas -
Polifonía máxima (notas) 4
Color del producto Gris
Exhibición
Pantalla incorporada
Tipo de visualizador LED
Número de caracteres en pantalla 4
Peso y dimensiones
Ancho 300mm
Profundidad 128mm
Altura 46mm
Peso 965g
Puertos e Interfaces
Cantidad de puertos USB 1
MIDI
Salida MIDI
Control de energía
Alimentación Batería
Tipo de batería AA
Numero de baterías soportadas 4
Contenido del embalaje
Pilas incluidas

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más