Sony ICF-C717PJ

Sony ICF-C717PJ manual

(3)
  • English
    WARNING
    To reduce the risk of fire or electric shock, do
    not expose this apparatus to rain or
    moisture.
    To reduce the risk of fire, do not cover the
    ventilation of the apparatus with newspapers,
    tablecloths, curtains, etc. And do not place lighted
    candles on the apparatus.
    To reduce the risk of fire or electric shock, do not
    expose this apparatus to dripping or splashing,
    and do not place objects filled with liquids, such
    as vases, on the apparatus.
    Do not install the appliance in a confined space,
    such as a bookcase or built-in cabinet.
    Do not expose the batteries (battery pack or
    batteries installed) to excessive heat such as
    sunshine, fire or the like for a long time.
    As the main plug is used to disconnect the unit
    from the mains, connect the unit to an easily
    accessible AC outlet. Should you notice an
    abnormality in the unit, disconnect the main plug
    from the AC outlet immediately.
    The unit is not disconnected from the AC power
    source (mains) as long as it is connected to the
    wall outlet, even if the unit itself has been turned
    off.
    The nameplate and important information
    concerning safety are located on the bottom
    exterior.
    CAUTION
    Danger of explosion if battery is incorrectly
    replaced. Replace only with the same type.
    Notice for customers: the following
    information is only applicable to equipment
    sold in countries applying EU directives
    The manufacturer of this product is Sony
    Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-
    0075 Japan. The Authorized Representative for
    EMC and product safety is Sony Deutschland
    GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
    Germany. For any service or guarantee matters
    please refer to the addresses given in separate
    service or guarantee documents.
    Features
    
    Dual alarm FM/AM synthesized clock radio
    
    Nature Sound (Sea Waves, Birds, Rain, Brook,
    Under the Sea)
    
    Temperature display (Centigrade/Fahrenheit)
    –15 °C – 50 °C (5 °F – 122 °F)
    
    Built-in audio cable for Digital Music Player
    
    10 Station Presets (5 FM/5 AM)
    
    Various types of alarms - radio, buzzer and
    Nature Sounds (5)
    
    Automatic time set: when you plug the clock in
    for the first time, the current time will be
    shown in the display (except East European
    model)
    
    Automatic Daylight Savings Time Set/Summer
    Time adjustment (except East European
    model).
    
    100 year calendar and DATE/TIME ZONE
    (DATE/DST) button to display year, month and
    date
    
    Brightness Control (High/Low/Off)
    
    No Power No Problem alarm system to keep
    the clock and the alarm operating during a
    power interruption with a CR2032 battery
    installed
    
    Extendable Snooze system - Snooze time can be
    set from 10 to 60 minutes
    
    Progressive Alarm Speed (buzzer only)
    Connecting the aerial
    To connect the AM loop
    aerial
    The shape and the length of the aerial is designed
    to receive AM signals. Do not dismantle or roll up
    the aerial.
    1 Remove only the loop part from the
    plastic stand.
    2 Set up the AM loop aerial.
    3 Connect the cords to the AM aerial
    terminals.
    Cord (A) or cord (B) can be connected either
    way round.
    A
    B
    Only insert up
    to here.
    Insert the cord while
    pushing down the
    terminal clamp.
    4 Make sure the AM loop aerial is
    connected firmly by pulling softly.
    Adjusting the AM loop aerial
    Find a place and an orientation that provides
    good reception.
    
    Do not place the AM loop aerial near the unit
    or other AV equipment, as noise may result.
    Tip
    Adjust the direction of the AM loop aerial for best
    AM broadcast sound.
    About the backup
    battery
    To maintain accurate time, this unit includes an
    internal CR2032 battery as a backup power source
    in the event of a power interruption (The battery
    is supplied with the unit for East European
    model.).
    Note for customers in Europe
    (except East Europe)
    The clock is preset at the factory, and its memory
    is powered by the preinstalled Sony CR2032
    battery. If the “0:00” flashes in the display when
    the unit is connected to AC outlet for the first
    time, the battery may be weak. In this case,
    consult a Sony dealer. The preinstalled CR2032
    battery is considered part of the product, and is
    covered by the warranty. You are required to show
    “Note for customers in Europe (except East
    Europe)” (in these instructions) to a Sony dealer
    in order to validate the warranty for this product.
    Knowing when to replace the
    battery
    When the battery becomes weak, “
    ” will
    appear in the display.
    If a power interruption occurs while the battery is
    weak, the current time and alarm will be
    initialized.
    Replace the battery with a Sony CR2032 lithium
    battery. Use of another battery may cause a fire or
    explosion.
    Installing and replacing the
    battery
    1 Keep the AC plug connected to the AC
    outlet, remove the screw that secures the
    battery compartment at the bottom of
    the unit using a screwdriver, and pull the
    battery compartment marked PULL
    OPEN. (See fig. -)
    2 Insert a new battery in the battery holder
    with the side facing up.
    To remove the battery from the battery
    compartment, push it out from the side
    marked PUSH. (See fig. -)
    3 Insert the battery compartment back into
    the unit and secure it with the screw.
    (See fig. -)
    4 When you are replacing the battery, press
    any of the following buttons: RADIO
    BAND, AUDIO IN, or NATURE SOUND
    / PRESET to turn “
    ” off in the display.
    Note
    When you replace the battery, do not disconnect
    the AC plug from AC outlet. Otherwise, the 100
    year calendar, current time, alarm and station
    presets will be initialized
    Setting the clock for
    the first time (except
    East European model)
    This unit is preset to current date and time at the
    factory, and is powered by the back up battery. All
    you need to do the first time is just plug it in and
    select your time zone.
    1 Plug in the unit.
    “year” (about 4 seconds) month and date
    (about 4 seconds) current CET (Central
    Standard Time)” appears in the display in
    turn.
    2 Press and hold DATE/TIME ZONE for at
    least 2 seconds.
    Area number “1” flashes in the display.
    3 Press TIME SET + or repeatedly to
    select the time zone as follows:
    Area number Time zone
    1 (default) Central European Time/
    Central European
    Summer Time
    2 Eastern European Time/
    Eastern European
    Summer Time
    0 Western European Time/
    Western European
    Summer Time
    4 Press DATE/TIME ZONE to set.
    Notes
    
    Though the clock is correctly set at the factory,
    discrepancies may arise during transport or
    storage. If necessary, set the clock to the correct
    time by referring to “Setting the clock.
    
    While setting the time zone, you must perform
    each step within 65 seconds, or the time zone
    setting mode will be cancelled.
    When daylight saving time
    (summer time) begins
    This model automatically adjusts for daylight
    saving time (summer time).
    ” is displayed from the beginning of daylight
    saving time (summer time), and disappears at the
    end of daylight saving time (summer time)
    automatically.
    Automatic DST/summer time adjustment is based
    on GMT (Greenwich Mean Time).
    Area number 1:
    
    Daylight saving time (summer time) begins at:
    2:00 AM on the final Sunday of March.
    
    Standard time begins at: 3:00 AM on the final
    Sunday of October.
    Area number 2:
    
    Daylight saving time (summer time) begins at:
    3:00 AM on the final Sunday of March
    
    Standard time begins at: 4:00 AM on the final
    Sunday of October.
    Area number 0:
    
    Daylight saving time (summer time) begins at:
    1:00 AM on the final Sunday of March.
    
    Standard time begins at: 2:00 AM on the final
    Sunday of October.
    To cancel Automatic DST/Summer Time
    adjustment during the daylight saving
    time (summer time) period
    Automatic DST/Summer Time adjustment can be
    canceled.
    Press and hold DISPLAY/CLOCK and SNOOZE /
    BRIGHTNESS at the same time for at least 2
    seconds while the clock is displayed.
    ” and “OFF” appear in the display to show that
    Automatic DST/Summer Time adjustment has
    been canceled. The display returns to the clock.
    Notes
    
    Time change of Automatic DST/Summer Time
    adjustment (see above) is subject to variations
    in circumstances and laws of each country/
    region. Cancel Automatic DST/Summer Time
    adjustment and set the DST display manually as
    necessary. Customers living in a country/region
    that does not use daylight saving time (summer
    time) must cancel Automatic DST/Summer
    Time adjustment before using the unit.
    
    To activate Automatic DST/Summer Time
    adjustment again, press and hold DISPLAY/
    CLOCK and SNOOZE / BRIGHTNESS at the
    same time for at least 2 seconds.
    ” and “On” appear in the display to show
    that Automatic DST/Summer Time adjustment
    has been activated. The display returns to the
    clock.
    Setting the clock
    Follow the procedure from step 1 for East
    European model. To change the setting for other
    models, follow the procedure from step 2.
    1 Plug in the unit.
    2 Press and hold DISPLAY/CLOCK for at
    least 2 seconds.
    The year starts to flash in the display.
    3 Press TIME SET + or repeatedly to set
    the year.
    4 Press DISPLAY/CLOCK.
    5 Repeat steps 3 and 4 to set the month,
    day, hour and minute, and then press
    DISPLAY/CLOCK.
    The seconds start incrementing from zero.
    Notes
    
    While setting the clock, you must perform each
    step within 65 seconds, or the clock setting
    mode will be cancelled.
    
    When pressing any of the rear buttons, hold the
    unit firmly to prevent slippage.
    To display the year and date
    Press DATE/TIME ZONE once for the year, and
    press again for the date.
    After a while, the display will change back to the
    current time automatically.
    To change the display to the daylight
    saving time (summer time) indication
    Change the daylight saving time (summer time)
    adjustment setting according to the following
    procedures if:
    – you have an East European model.
    you have cancelled the Automatic DST/Summer
    Time adjustment.
    Press and hold DATE/DST.
    ” appears in the display and the time indication
    changes to daylight saving time (summer time).
    To deactivate the daylight saving time (summer
    time) adjustment, press DATE/DST again.
    Using the Projector
    function
    The Projector function allows you to display the
    clock and alarm on a nearby wall, up to a distance
    of 2 metres away.
    Pressing the PROJECTION ROTATE button
    repeatedly changes the angle of rotation at which
    the clock and alarm appear.
    How to use
    1 Plug in the unit.
    2 Select the location and height.
    3 Press the PROJECTION ON/OFF button.
    4 To adjust the focus, turn PROJECTION
    FOCUS.
    5 To press the PROJECTION ROTATE
    button repeatedly changes the angle of
    rotation at which the clock and alarm
    appear. (See fig. )
    Notes
    
    The Projector function cannot be used unless
    the clock has been set.
    
    Do not stare into the lens directly.
    
    Certain walls may not display the projection
    properly.
    
    The projector can be rotated 90° left or right
    from the upward position, and clicks when
    returned to the upward position.
    
    If the projector unit is rotated beyond limited, it
    may be damaged.
    
    The projector will automatically turn off after
    10 hours.
    Setting the brightness
    of the display
    Three levels of brightness are available by pressing
    SNOOZE / BRIGHTNESS.
    Note
    When the alarm is sounding, the brightness
    function cannot be used.
    Operating the radio
    Manual tuning
    1 Press RADIO BAND to turn on the
    radio and select the AM or FM band.
    2 Press TUNING + or to tune in to a
    desired frequency.
    3 Adjust the volume using VOL + or .
    Note
    The FM frequency display is raised or lowered by
    a step of 0.1 MHz. For example, frequency 88.00
    and 88.05 MHz is displayed as “88.0.
    Tuning in to a station
    The unit automatically scans AM or FM stations.
    1 Press RADIO BAND to turn on the
    radio to select the AM or FM band.
    2 Press and hold TUNING + or .
    + : scans upward through the frequency
    bands.
    – : scans downwards through the frequency
    bands.
    Scanning starts from the currently-tuned
    frequency. When a station is received,
    scanning stops.
    3 Adjust the volume using VOL + or .
    4-180-721-31(1)
    Setting the Nature Sound alarm
    1 Perform steps 1 to 5 in “To set the
    alarm.
    2 Press TIME SET + or to select
    “NATURE SOUND” alarm mode, and
    press ALARM ON/OFF A or B.
    “NATURE SOUND” appears in the
    display.
    3 Press TIME SET + or to select the
    NATURE SOUND / PRESET 1 to 5, and
    press ALARM ON/OFF A or B.
    4 Press TIME SET + or to adjust the
    volume, and press ALARM ON/OFF A or
    B.
    The setting is entered.
    5 Press ALARM ON/OFF A or B. “” or
    ” appears in the display after about 4
    seconds.
    The Nature sound will sound at the set time.
    Setting the radio alarm
    1 Perform steps 1 to 5 in “To set the
    alarm.
    2 Press TIME SET + or to select
    “RADIO” alarm mode, and press
    ALARM ON/OFF A or B.
    “RADIO” appears in the display.
    3 Press TIME SET + or to select the AM
    band, FM band or the last station, and
    press ALARM ON/OFF A or B.
    If you select the last station, jump to step 5.
    4 Press TIME SET + or to select the
    station, and press ALARM ON/OFF A or
    B.
    5 Press TIME SET + or to adjust the
    volume, and press ALARM ON/OFF A or
    B.
    The setting is entered.
    6 Press ALARM ON/OFF A or B. “” or
    ” appears in the display after about 4
    seconds.
    The radio will sound at the set time.
    Setting the Buzzer Alarm
    1 Perform steps 1 to 5 in “To set the
    alarm.
    2 Press TIME SET + or to select
    “BUZZER” alarm mode, and press
    ALARM ON/OFF A or B.
    The setting is entered.
    3 Press ALARM ON/OFF A or B. “” or
    ” appears in the display after about 4
    seconds.
    The buzzer will sound at the set time.
    When the alarm setting is completed, the alarm
    time setting is displayed.
    When both ALARM” and ALARM” are
    turned on, you can switch the ALARM A and
    ALARM B display by pressing DISPLAY/CLOCK.
    Notes
    
    When you use the radio alarm, the timed alarm
    sounds with the last broadcasting station tuned
    to before the power went off. When you set the
    radio alarm, select the desired broadcasting
    station before turning the power off.
    
    The ALARM” (or “”) indicator flashes in
    the display when the alarm sounds.
    
    If a second alarm sounds during a first (or the
    SNOOZE function is active), the second alarm
    takes priority.
    
    The alarm function works as usual at the
    beginning and end day of daylight saving time
    (summer time). While Automatic DST/
    Summer Time adjustment is set, as a result, if
    the alarm is set at a time skipped when the
    daylight saving time (summer time) begins, the
    alarm is skipped, or if the alarm is set at a time
    overlapped when the daylight saving time
    (summer time) ends, the alarm sounds twice.
    
    If the same alarm time is set for both alarms
    (ALARM A and B), ALARM A takes priority.
    To confirm an alarm time setting
    Turn off the ALARM ON/OFF” or “
    indicator in the display, and press the ALARM
    ON/OFF A or B button again.
    You can confirm the alarm time by pressing TIME
    SET + or after the alarm time is set.
    To change an alarm setting
    There are two ways to set the alarm:
    To change all alarm settings
    Set the alarm again.
    To change an alarm time only
    When setting the alarm (ALARM” or
    ALARM” appears), this function is available.
    Press and hold TIME SET + for at least 2 seconds
    to move the alarm time forwards. Press and hold
    TIME SET – for at least 2 seconds to move the
    alarm time back. When you release the button,
    the changed time will be displayed for about 2
    seconds. To change the alarm time, press TIME
    SET + or within these 2 seconds, otherwise the
    setting change will be fixed as displayed.
    To doze for a few more minutes
    Press SNOOZE / BRIGHTNESS.
    The sound turns off but will automatically come
    on again after about 10 minutes.
    You can change the snooze time by pressing
    SNOOZE / BRIGHTNESS repeatedly within
    4 seconds.
    The maximum snooze time is 60 minutes.
    To stop the alarm
    Press OFF ALARM RESET to turn off the alarm.
    The alarm will sound again at the same time
    depending on the next day setting.
    To deactivate the alarm
    Press ALARM ON/OFF A or B to turn off the
    ALARM” or “” indicator in the display.
    Preset tuning
    You can preset 5 stations for FM and 5 stations for
    AM.
    Presetting a station
    1 Follow steps 1 and 2 in “Manual tuning
    to tune the frequency you wish to preset.
    2 Hold down the desired NATURE
    SOUND / PRESET 1 to 5 button until
    you hear two beeps.
    Example: The following display appears
    when you preset FM 105.7 MHz to preset
    number 3 for FM.
    The display shows the frequency for a few
    seconds and then changes back to the current
    time. To change the preset station, tune into
    the desired station and hold down the
    NATURE SOUND / PRESET 1 to 5 button
    until you hear two beeps.
    To preset another station, repeat these steps.
    Note
    If you try to store another station with the same
    preset number, the previously stored station will
    be replaced.
    Tuning in to a preset station
    1 Press RADIO BAND to turn on the
    radio and select the AM or FM band.
    2 Press NATURE SOUND / PRESET 1 to 5
    where the desired station is stored.
    3 Adjust the volume using VOL + or .
    Improving the
    reception
    FM: Extend the FM wire aerial fully to increase
    reception sensitivity.
    AM: Connect the supplied AM loop aerial to the
    unit. Rotate the aerial horizontally for
    optimum reception.
    Note on radio reception
    Keep digital music players or mobile phones away
    from the AM loop aerial or the FM aerial, as this
    may lead to reception interference.
    Selecting a Nature
    Sound
    This unit includes 5 types of Nature Sounds: (Sea
    Waves, Birds, Rain, Brook and Under the Sea.)
    You can choose any one of these by pressing the
    corresponding button.
    Icons Sound type
    Sea Waves
    Birds
    Rain
    Brook
    Under the Sea
    Note
    When other functions are in use, Nature Sound is
    not available.
    Setting the alarm
    The dual alarm function allows you to set two
    alarm programs (ALARM ON/OFF A and
    ALARM ON/OFF B).
    The alarm time can be set for each program and
    the alarm sound is selectable from “NATURE
    SOUND,” “RADIO,” or “BUZZER.
    Notes
    
    Before setting the alarm, make sure to set the
    clock. (See “Setting the clock”)
    
    The factory setting alarm time is “12:00.
    
    To set the radio alarm, first preset your favorite
    station. (See “Presetting a station”)
    
    While setting the alarm, you must perform each
    step within 65 seconds, or the alarm setting
    mode will be cancelled.
    To set the alarm
    1 Press and hold ALARM ON/OFF A or B
    for a few seconds.
    2 Press TIME SET + or to set the desired
    hour, and press ALARM ON/OFF A or B.
    3 Press TIME SET + or to set the desired
    minute, and press ALARM ON/OFF A or
    B.
    4 Press TIME SET + or to set the desired
    alarm period (“WEEKDAY,
    “WEEKEND” or everyday*), and press
    ALARM ON/OFF A or B.
    * In the case of everyday, both “WEEKDAY”
    and “WEEKEND” are displayed.
    5 Press TIME SET + or to set the desired
    alarm mode (“NATURE SOUND,
    “RADIO,” or “BUZZER”), and press
    ALARM ON/OFF A or B.
    You can choose one of 3 settings: “NATURE
    SOUND,” “RADIO,” or “BUZZER.” Set the
    alarm mode as follows:
    NATURE SOUND: see “
    Setting the
    Nature Sound alarm.
    – RADIO: see “ Setting the radio alarm.
    – BUZZER: see “ Setting the buzzer alarm.
    Note on the alarm in the event of a power
    interruption
    In the event of a power interruption, the alarm
    will work until the internal battery is worn out.
    However, certain functions may be affected as
    follows:
    
    The backlight will not light up.
    
    If the alarm mode is set to Nature Sound or
    radio, it will change to BUZZER automatically.
    
    If a power interruption occurs while the alarm
    is sounding, the alarm will stop.
    
    If OFF ALARM RESET is not pressed, the
    alarm will sound for about 5 minutes.
    
    If “
    ” appears in the display, the alarm will
    not sound in the event of power interruption.
    Replace the battery if “
    ” appears.
    
    The snooze function will not work.
    
    During a power interruption, the alarm will
    sound at the set time only once.
    Setting the sleep timer
    You can fall asleep to the “NATURE SOUND,
    “RADIO,” or “AUDIO IN” using the built-in sleep
    timer that turns off the “NATURE SOUND,
    “RADIO,” or “AUDIO IN” automatically after a
    preset duration.
    1 Press SLEEP while the unit is turned on.
    “SLEEP” appears and the sleep time flashes in
    the display.
    2 Press SLEEP to set the sleep timer
    duration.
    Each time you press SLEEP, the duration (in
    minutes) changes as follows:
    90 60 30 15
    OFF
    The display returns to clock mode for about
    4 seconds after you have finished the duration
    setting and released SLEEP, and then the sleep
    timer starts.
    The unit will play for the duration you set, and
    then shut off.
    Note
    Even if the Sleep Timer is set, it cannot turn off
    the power of optional components connected to
    the AUDIO IN jack of this player.
    To turn off the unit before the preset
    time
    Press OFF ALARM RESET.
    To change the sleep timer setting
    You can press SLEEP repeatedly to select the
    desired sleep timer setting even after the sleep
    timer has been activated.
    To deactivate the sleep timer
    Press SLEEP repeatedly to set the sleep timer to
    OFF” in step 2.
    Using the temperature
    function
    This unit includes an external temperature sensor,
    allowing you to monitor ambient temperature.
    The temperature is displayed in Centigrade or
    Fahrenheit.
    To switch between Centigrade and Fahrenheit,
    press and hold the SNOOZE / BRIGHTNESS and
    DATE/TIME ZONE (SNOOZE / BRIGHTNESS
    and DATE/DST) buttons for more than 2 seconds.
    Notes
    
    In the example, the display shows Centigrade;
    however, Fahrenheit can also be displayed.
    
    Do not use in water.
    
    Do not forcefully pull on the external
    temperature sensor. Improper use of the
    external temperature sensor may cause a
    malfunction.
    
    The display temperature and actual temperature
    may differ depending on the usage
    environment.
    
    Do not place the temperature sensor near the
    floor, a heat source such as a radiator or airduct,
    or in a place subject to direct sunlight.
    The temperature sensor reading may differ
    from actual surrounding temperature.
    
    The operating temperature range is –15 °C
    (5 °F) to 50 °C (122 °F).
    In the case of lower than –15 °C (5 °F) or higher
    than 50 °C (122 °F), the “Lo” or “Hi” indicator
    appears.
    
    When plugging in the unit or recovering from a
    power interruption, the temperature display of
    this unit will flash "--".
    The temperature will be displayed after 20
    seconds.
    Connecting external
    equipment (See fig. )
    To listen to sound
    1 Connect the built-in audio cable with the
    stereo-miniplug on the bottom of the
    unit to the line output jack or
    headphones jack on the optional
    component (e.g., portable music player).
    2 Press AUDIO IN.
    AUDIO IN” appears in the display.
    3 Play the optional component connected
    to the units built-in audio cable.
    4 Adjust the volume using VOL + or and
    the connected components volume.
    To return to the radio
    Press RADIO BAND.
    The frequency is shown in the display.
    To stop listening
    Press OFF ALARM RESET, and stop playback
    on the connected unit.
    To turn off the sound from the optional
    component
    Press OFF ALARM RESET, and then turn off the
    optional component.
    Notes
    
    Refer also to the connected equipments
    manual.
    
    Connect the audio cable firmly to prevent a
    malfunction.
    
    Keep digital music players away from the
    speaker.
    
    If you increase the volume too much, loud
    sound may occurs when switching to the radio.
    
    Confirm the volume when you remove the
    connected component from this unit to listen
    by headphones. Otherwise, high volume may
    affect your hearing.
    
    AUDIO IN cannot be set for the alarm sound.
    
    When you listen to the radio with external
    equipment connected, turn off the connected
    equipment to prevent noise. If noise occurs,
    even when the equipment is turned off,
    disconnect and place the external equipment
    away from the unit.
    ©2010 Sony Corporation Printed in China
    FM/AM Clock Radio
    Operating Instructions
    Manual de instrucciones (en el reverso)
    ICF-C717PJ
    Dream Machine is a trademark of Sony Corporation.
    Dream Machine es marca comercial de Sony Corporation.
    Troubleshooting
    Should any problem persist after you have made
    the following checks, consult your nearest Sony
    dealer.
    The clock flashes 0:00 due to a power
    interruption.
    
    The battery is low. Replace the battery. Remove
    the old battery and install a new one.
    The radio, Nature sound or buzzer alarm
    does not sound at the preset alarm time.
    
    Check that alarm “” or alarm “” is
    properly set/displayed.
    The alarm settings are activated but there is
    no sound at the preset alarm time.
    
    Check the alarm volume setting.
    When daylight saving time begins, the clock
    does not employ the daylight saving time
    automatically.
    
    Make sure the clock is set correctly.
    
    Press and hold DISPLAY/CLOCK and SNOOZE
    / BRIGHTNESS simultaneously for at least 2
    seconds to activate the Automatic DST
    function.
    Precautions
    
    Operate the unit on the power source specified
    in “Specifications.
    
    To disconnect the power cord (mains lead), pull
    it out by the plug, not the cord.
    
    Since a strong magnet is used for the speaker,
    keep personal credit cards using magnetic
    coding or spring-wound watches away from the
    unit to prevent possible damage from the
    magnet.
    
    Do not leave the unit in a location near a heat
    source such as a radiator or airduct, or in a
    place subject to direct sunlight, excessive dust,
    mechanical vibration, or shock.
    
    Allow adequate air circulation to prevent
    internal heat build-up. Do not place the unit on
    a thick pile surface (rug, a blanket, etc.), or near
    materials that might block the ventilation holes
    (such as a curtain, etc. ).
    
    Should any solid object or liquid fall into the
    unit, unplug the unit and have it checked by
    qualified personnel before operating it any
    further.
    
    To clean the casing, use a soft cloth dampened
    with a mild detergent solution.
    
    Never touch the wire of the external FM aerial
    during a thunderstorm. Furthermore,
    immediately disconnect the main plug from the
    wall outlet.
    NOTES ON THE LITHIUM BATTERY
    
    Wipe the battery with a dry cloth to assure a
    good contact.
    
    Be sure to observe the correct polarity when
    installing the battery.
    
    Do not hold the battery with metallic tweezers,
    otherwise a short-circuit may occur.
    Disposal of Old Electrical &
    Electronic Equipment (Applicable
    in the European Union and other
    European countries with separate
    collection systems)
    This symbol on the product or on its packaging
    indicates that this product shall not be treated as
    household waste. Instead it shall be handed over
    to the applicable collection point for the recycling
    of electrical and electronic equipment. By
    ensuring this product is disposed of correctly, you
    will help prevent potential negative consequences
    for the environment and human health, which
    could otherwise be caused by inappropriate waste
    handling of this product. The recycling of
    materials will help to conserve natural resources.
    For more detailed information about recycling of
    this product, please contact your local Civic
    Office, your household waste disposal service or
    the shop where you purchased the product.
    Disposal of waste batteries
    (applicable in the European
    Union and other European
    countries with separate
    collection systems)
    This symbol on the battery or on the packaging
    indicates that the battery provided with this
    product shall not be treated as household waste.
    On certain batteries this symbol might be used in
    combination with a chemical symbol. The
    chemical symbols for mercury (Hg) or lead (Pb)
    are added if the battery contains more than
    0.0005% mercury or 0.004% lead.
    By ensuring these batteries are disposed of
    correctly, you will help prevent potentially
    negative consequences for the environment and
    human health which could otherwise be caused
    by inappropriate waste handling of the battery.
    The recycling of the materials will help to
    conserve natural resources.
    In case of products that for safety, performance or
    data integrity reasons require a permanent
    connection with an incorporated battery, this
    battery should be replaced by qualified service
    staff only.
    To ensure that the battery will be treated properly,
    hand over the product at end-of-life to the
    applicable collection point for the recycling of
    electrical and electronic equipment.
    For all other batteries, please view the section on
    how to remove the battery from the product
    safely. Hand the battery over to the applicable
    collection point for the recycling of waste
    batteries.
    For more detailed information about recycling of
    this product or battery, please contact your local
    Civic Office, your household waste disposal
    service or the shop where you purchased the
    product.
    If you have any questions or problems concerning
    your unit, consult your nearest Sony dealer.
    Specifications
    Time display
    24-hour system
    Radio section
    Frequency range
    Band Frequency Channel step
    FM 87.5 – 108 MHz 0.05 MHz
    AM 531 – 1 602 kHz 9 kHz
    General
    Speaker
    Approx. 3.6 cm (1
    7
    /
    16
    inches) dia. 8 Ω
    Input
    Built-in audio cable with stereo-mini plug
    (ø 3.5 mm)
    Power output
    0.7 W (at 10% harmonic distortion)
    Power requirements
    230 V AC, 50 Hz
    For clock back up: 3V DC, one CR2032 battery
    Nature sound
    Sea Waves, Birds, Rain, Brook and Under the Sea
    Temperature range
    –15 °C – 50 °C (5 °F – 122 °F)
    Temperature resolution
    1 °C (1 °F)
    Dimensions
    Approx. 217 mm × 67 mm × 62 mm (w/h/d)
    (8
    5
    /
    8
    inches × 2
    3
    /
    4
    inches × 2
    1
    /
    2
    inches) not
    including projecting parts and controls
    Mass
    Approx. 670 g (1 lb 7.63 oz) including power
    supply unit and CR2032 battery
    Supplied accessories
    AM loop aerial (1)
    Lithium battery CR2032 (1) (East European
    model only)
    Design and specifications are subject to change
    without notice
    No Power No Problem is a trademark of Sony Corporation.
    No Power No Problem es una marca comercial de Sony Corporation.
    Model for other countries/regions:
    The VOL + button has a tactile dot.
    Button legending of DATE/TIME ZONE and DATE/DST button differs between countries/
    regions.
    Model for Europe
    (except for East European model):
    FM wire aerial
    Temperature
    sensor
    AC power cord
    Built-in audio
    cable
    CR2032
    Built-in audio
    cable
    The built-in audio cable can
    be inserted in the slot of the
    unit.
    To the headphones
    jack or line output
    jack
Sony ICF-C717PJ

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Sony ICF-C717PJ o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Sony ICF-C717PJ responder adecuadamente a su pregunta.

Vea el manual de Sony ICF-C717PJ aquí, de forma gratuita. Este manual pertenece a la categoría Radio despertadores y ha sido calificado por 3 personas con un promedio de 8.7. Este manual está disponible en los siguientes idiomas: Español, Inglés. ¿Tiene alguna pregunta sobre Sony ICF-C717PJ o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Sony ICF-C717PJ

No es necesario comprar altavoces externos para obtener un audio excelente. Gracias a sus altavoces integrados, esta pan...
General
Marca Sony
Modelo ICF-C717PJ
Producto Radio despertador
EAN 4905524647259
Idioma Español, Inglés
Tipo de archivo PDF
Radio
Tipo de radio Personal
Tipo de sintonizador Digital
Bandas de radio soportadas AM,FM
Sintetizador PLL No
Banda FM 87.5 - 108 MHz
Banda AM 531 - 1602 kHz
Cantidad de estaciones predeterminadas 20
Audio
Potencia estimada RMS - W
Altavoces
Altavoces incorporados Si
Número de altavoces incorporados 1
Exhibición
Pantalla incorporada Si
Tipo de visualizador LCD
Puertos e Interfaces
Salidas para auriculares -
Características
Reproducción MP3 No
Color del producto Plata
Reloj
Alarma Si
Temporizador de apagado Si
Función snooze Si
Otras características
Compatibilidad con bases dock de Apple No compatible
Calendario Si
Monitor con luz de fondo Si
Voltaje de entrada 230 V
Peso y dimensiones
Ancho 215 mm
Profundidad 58 mm
Altura 60.5 mm
Peso 620 g
Batería
Numero de baterías soportadas 1
Tipo de batería CR2032
Voltaje de la pila 3 V
Control de energía
Frecuencia de entrada AC 50 Hz