Sony SRS-BTM8

Sony SRS-BTM8 manual

(1)
  • Wireless Speaker System
    ©2012 Sony Corporation Printed in China
    4-440-489-22(1)
    SRS-BTM8
    Operating Instructions
    Mode d’emploi
    Function of Parts
    / button
    Turns the system on/off.
    OPR/BATT indicator (green)
    Lights up when the system is turned on. Dims during battery
    operation if battery power is low.
    BLUETOOTH PAIRING button
    Press to pair with a Bluetooth device.
     (play/pause) button
    Operates a connected Bluetooth device. You cannot operate a
    device connected to the AUDIO IN jack.
    N-mark
    Touch to make Bluetooth connection with an NFC compatible
    smartphone.
    (call) button
    Press to call or operate during a call.
    VOLUME −/+ button
    Adjusts the volume. A beep sounds from the speakers when
    the volume is set to minimum or maximum.
    Handle
    Hold to carry the system.
    (Bluetooth) indicator (blue)
    Lights up or flashes depending on the communication status.
    For details, see the following section, “Indications of the
    Bluetooth function.
    Microphone
    Use during call.
    AUDIO IN jack
    Connects to the headphone jack of a portable audio device,
    computer, etc., using a connecting cord (not supplied).
    DC IN 6V jack
    Connects the supplied AC adaptor.
    Battery compartment
    Insert four alkaline LR6 (size AA) batteries (not supplied).
    Indications of the Bluetooth function
    Status
    (Bluetooth) indicator (blue)
    Pairing with a device Flashes quickly
    Searching for a device Flashes
    Connected to a device Lights up
    Turning the System on/off
    1 Connect the supplied AC adaptor.
    2 Press the / button.
    The OPR/BATT indicator (green) lights up.
    Indicator lights up.
    To use with LR6 (size AA) batteries (not supplied)
    1 Open the cover located on the bottom of the system and install four alkaline LR6 (size AA) batteries (not supplied), then close the
    cover.
    2 Press the / button.
    Note
    If the AC adaptor is used with the system, the power source switches to the wall outlet (mains) automatically, even if batteries are installed.
    Installed batteries cannot be the power source when the AC adaptor is connected to the system. Make sure the plug of the AC adaptor is
    disconnected from the system when using the system with batteries.
    How to Make Wireless Connection with Bluetooth
    Devices
    You can enjoy music and hands-free calling with the system wirelessly by using your device’s Bluetooth function.
    Choose one of the following three connection methods, best suited for the Bluetooth device. For details on how to operate your device,
    refer to the operating instructions supplied with the device.
    Pairing with a Bluetooth device: see
    Pattern A
    Bluetooth devices need to be “paired” with each other beforehand.
    Connecting with a paired device: see
    Pattern B
    To listen to music with a Bluetooth device that has been paired, see this pattern.
    One touch connection with a smartphone (NFC): see
    Pattern C
    Using an NFC compatible smartphone, you can establish a Bluetooth connection by just touching the system with it.
    Check the following before operating the system.
    Both the system and the device are placed within 1 m of each other.
    The system is connected to a power source, or batteries are installed in the system.
    The operating instructions supplied with the device are kept at hand.
    Pattern A
    Pairing and connecting with a Bluetooth device
    1 Turn on the system.
    2 Set the Bluetooth function of the Bluetooth device to on.
    For details, refer to the operating instructions supplied with the device.
    3 Press and hold the BLUETOOTH PAIRING button on the system until beeps are heard and the
    (Bluetooth) indicator (blue) begins to flash quickly.
    Tip
    When the system is turned on first, the
    (Bluetooth) indicator (blue) starts flashing quickly.
    Indicator flashes quickly.
    4 Perform the pairing procedure on the Bluetooth device to detect the system.
    If “SRS-BTM8” does not appear on the device’s display, repeat from step 2.
    Note
    Some devices cannot display a list of detected devices.
    5 Select “SRS-BTM8” shown in the display of the Bluetooth device.
    6 If Passcode* input is required on the display of the Bluetooth device, input “0000.
    The Bluetooth connection is established and the (Bluetooth) indicator (blue) on the system stays on.
    * Passcode may be called “Passkey, “PIN code, “PIN number, or “Password.
    Tip
    To pair with other
    Bluetooth devices, repeat steps 2 to 6 for each device.
    Notes
    Pairing mode of the system is cancelled after about 5 minutes, and the
    (Bluetooth) indicator (blue) flashes slowly. If the pairing mode is
    cancelled while performing this procedure, start over from step 3.
    Passcode of the system is fixed as “0000. The system cannot be paired with a
    Bluetooth device whose Passcode is not “0000.
    Once
    Bluetooth devices are paired, there is no need to pair those devices again. However, in the following cases, you will need to perform the
    pairing procedure again.
    Pairing information is deleted after repair, etc.
    The system is paired with 5 or more devices.
    The system can be paired with up to 4 Bluetooth devices. If a new device is paired after 4 devices have been paired, the device whose latest
    connection time is the oldest among the 4 paired devices is replaced by the new one.
    More than one device can be paired with the system, but sound will be heard from just one of those devices.
    To delete all pairing information from the system
    Hold the / button for more than 15 seconds while the system is turned off. The system is reset to its default and all pairing information is
    deleted.
    Pattern B
    Connecting with a paired Bluetooth device
    1 Turn on the system.
    The (Bluetooth) indicator (blue) flashes.
    2 Set the Bluetooth function of the Bluetooth device to on.
    Tip
    When turned on, the system tries to establish
    Bluetooth connection with the Bluetooth device connected to the system last time. When
    Bluetooth connection is established, the (Bluetooth) indicator (blue) on the system stays on.
    3 Select “SRS-BTM8” shown in the display of the Bluetooth device.
    If necessary, select a Bluetooth profile that the system supports from the following: A2DP, HSP or HFP. For details on each profile,
    see “Listening to Music” or “Using Hands-free Calling While Listening to Music.
    Note
    This step may not be necessary for some devices.
    The Bluetooth connection is established and the (Bluetooth) indicator (blue) on the system stays on.
    English Wireless Speaker System
    Before operating the system, please read this guide thoroughly
    and retain it for future reference.
    WARNING
    To reduce the risk of fire or electrical shock, do not open the
    cabinet. Refer servicing to qualified personnel only.
    To reduce the risk of fire, do not cover the ventilation opening of
    the apparatus with newspapers, tablecloths, curtains, etc. Do not
    place the naked flame sources such as lighted candles on the
    apparatus.
    To reduce the risk of fire or electric shock, do not expose this
    apparatus to dripping or splashing, and do not place objects
    filled with liquids, such as vases, on the apparatus.
    Do not install the appliance in a confined space, such as a
    bookcase or built-in cabinet.
    As the main plug of the AC adaptor is used to disconnect the AC
    adaptor from the mains, connect the system to an easily
    accessible AC outlet. Should you notice an abnormality in the
    system, disconnect the main plug from AC outlet immediately.
    The system is not disconnected from the mains as long as it is
    connected to the AC outlet, even if the system itself has been
    turned off.
    On Copyrights and Licenses
    The Bluetooth® word mark and logos are owned by the Bluetooth
    SIG, Inc. and any use of such marks by Sony Corporation is under
    license.
    The N Mark is a trademark or registered trademark of NFC Forum,
    Inc. in the United States and in other countries.
    Android is a trademark of Google Inc.
    Other trademarks and trade names are those of their respective
    owners.
    CAUTION
    You are cautioned that any changes or modifications not
    expressly approved in this manual could void your authority to
    operate this equipment.
    Precautions
    Notes when using with a mobile phone
    For details on operation of your mobile phone when receiving
    a telephone call while transmitting the sound using the
    Bluetooth connection, refer to the operating instructions
    supplied with the mobile phone.
    On safety
    The nameplate indicating Sony trademark, model number and
    electrical rating is located on the bottom exterior of this system
    and on the surface of the AC adaptor.
    Notes on the AC adaptor
    When connecting or disconnecting the AC adaptor, turn off
    the system beforehand. Otherwise, it may cause malfunction.
    Use only the supplied AC adaptor. To avoid damaging the
    system, do not use any other AC adaptor.
    Polarity of the plug
    Plug the AC adaptor into a nearby wall outlet (mains). In the
    case of a problem, unplug it from the wall outlet (mains)
    immediately.
    Do not install the AC adaptor in a confined space, such as a
    bookcase or built-in cabinet.
    To reduce the risk of fire or electric shock, do not expose the
    AC adaptor to dripping or splashing, and do not place objects
    filled with liquids, such as vases, on the AC adaptor.
    On placement
    Do not set the speaker in an inclined position.
    Do not leave the system in a location near heat sources, or in a
    place subject to direct sunlight, excessive dust, moisture, rain
    or mechanical shock.
    Do not expose the battery to excessive heat such as direct
    sunlight, fire or the like.
    On operation
    Do not insert any small objects, etc., into the jacks. The system
    may short out or malfunction.
    On cleaning
    Do not use alcohol, benzine, or thinner to clean the cabinet.
    Others
    If you have any questions or problems concerning this system
    that are not covered in this manual, please consult your
    nearest Sony dealer.
    Pattern C
    Connecting with a smartphone by One touch (NFC)
    By just touching the system with an NFC compatible smartphone, the system is turned on automatically and then paired and
    connected with the smartphone.
    1 Download and install the app “NFC Easy Connect on the smartphone.
    “NFC Easy Connect” is an original app by Sony for Android phones, and is available at Google Play Store.
    Search for “NFC Easy Connect” or scan the following two-dimensional code to download and install the free app. Communication
    fees are required to download the app.
    The App may not be available in some countries and/or regions.
    By the two-dimensional code:
    Use a two-dimensional code reader app.
    Compatible smartphones
    Smartphones with the NFC function built-in
    (OS: Android 2.3.3 or later, excluding Android 3.x)
    Customers in Europe
    Access the following Web site for details:
    http://support.sony-europe.com
    About NFC
    NFC (Near Field Communication) is a technology enabling short-range wireless communication between various devices, such as
    mobile phones and IC tags. Thanks to the NFC function, data communication can be achieved easily just by touching the relevant
    symbol or designated location on NFC compatible devices.
    2 Start the app “NFC Easy Connect on the smartphone.
    Make sure that the application screen is displayed.
    3 Touch the system with the smartphone.
    Keep touching the smartphone on the N marked part of the system until the smartphone vibrates.
    Smartphone vibrates
    (system recognized)
    Indicator lights up.
    Follow the on-screen instructions to establish the connection.
    When the Bluetooth connection is established, the (Bluetooth) indicator (blue) stays on.
    Tips
    If it is difficult to establish the connection, try the following.
    Activate the app “NFC Easy Connect” and move the smartphone slightly on the N marked part of the system.
    If the smartphone is in a case, remove it.
    Touch the system with the smartphone again to disconnect.
    If you have multiple NFC compatible devices, just touch the smartphone to a different device to switch the connection to that device. For
    example, when your smartphone is connected with NFC compatible headphones, just touch the smartphone to the system to change the
    Bluetooth connection to the system (One touch connection switching).
    Listening to Music
    You can enjoy listening to music and basic remote control operation of a Bluetooth device via Bluetooth connection. The Bluetooth
    device is required to support the following Bluetooth profiles.
    A2DP (Advanced Audio Distribution Profile): enables you to enjoy high-quality audio content wirelessly.
    AVRCP (Audio Video Remote Control Profile): enables you to enjoy basic remote control operation (play, stop, etc.) of a Bluetooth
    device.
    Operations may vary depending on the Bluetooth device. Refer also to the operating instructions supplied with your Bluetooth device.
    1 Make the Bluetooth connection between the system and the device.
    For details on the Bluetooth connection procedure, see “How to Make Wireless Connection with Bluetooth Devices. When the
    Bluetooth connection is established, the (Bluetooth) indicator (blue) on the system stays on.
    2 Start playback on the Bluetooth device, then adjust the volume.
    Set the volume of the Bluetooth device to a moderate level, and press the VOLUME –/+ buttons on the system.
    Pressing  (play/pause) button on the system, you can operate a Bluetooth device that supports AVRCP. Available functions
    may vary depending on the Bluetooth device. Refer to the operating instructions supplied with the Bluetooth device.
    After use
    Do any of the following.
    Set the
    Bluetooth function of the Bluetooth device to off. For details, refer to the operating instructions supplied with the device.
    Turn off the
    Bluetooth device.
    Turn off the system.
    Touch the system with the smartphone again to disconnect (NFC compatible smartphones only).
    Tip
    When connected with a
    Bluetooth device via A2DP/AVRCP and playback has been stopped for about 20 minutes, the system turns off
    automatically.
    Using Hands-free Calling While Listening to Music
    You can enjoy hands-free calling via Bluetooth connection with a Bluetooth mobile phone that has a music function and supports the
    Bluetooth profile A2DP (Advanced Audio Distribution Profile), and HFP (Hands-free Profile) or HSP (Headset Profile).
    If your Bluetooth mobile phone supports both HFP and HSP, set to HFP.
    Operations may vary depending on the Bluetooth mobile phone. Refer also to the operating instructions supplied with your mobile
    phone.
    1 Make the Bluetooth connection between the system and the mobile phone.
    For details on the Bluetooth connection procedure, see “How to Make Wireless Connection with Bluetooth Devices. When the
    Bluetooth connection is established, the (Bluetooth) indicator (blue) on the system stays on.
    2 Start playback on the Bluetooth mobile phone, then adjust the volume.
    Set the volume of the Bluetooth mobile phone to a moderate level, and press the VOLUME –/+ buttons on the system.
    By pressing the  (play/pause) button on the system, you can operate a Bluetooth mobile phone that supports AVRCP.
    Available functions may vary depending on the Bluetooth mobile phone. Refer to the operating instructions supplied with the
    Bluetooth mobile phone.
    To call
    Operate the Bluetooth mobile phone. Check that a dialing tone is heard on the system and talk using the microphone. If no dialing
    tone is heard, press the (call) button on the system for about 2 seconds to change the call device to the system.
    To receive a call
    When an incoming call arrives, the playback pauses and a ring tone is heard from the system. Press the (call) button on the system
    and talk using the microphone.
    Tips
    If no ring tone is heard from the system when incoming call arrives, stop playback and press the
    (call) button to talk.
    You can use the hands-free calling when playback is completed.
    During a call, press the VOLUME –/+ buttons on the system to adjust the volume. The volume of a call and that of a playback are set separately.
    Note
    When using a mobile phone, keep it 50 cm or more away from the system. If they are too close together, noise may be heard.
    To end a call
    Press the (call) button. If you were listening to music when the call arrived, it will be resumed when the call has finished.
    After use
    Do any of the following.
    Set the Bluetooth function of the Bluetooth device to off. For details, refer to the operating instructions supplied with the device.
    Turn off the Bluetooth device.
    Turn off the system.
    Touch the system with the smartphone again to disconnect (NFC compatible smartphones only).
    Unit button functions during a call
    Available functions may vary depending on the Bluetooth mobile phone, or the profiles supported by the Bluetooth mobile phone.
    Refer to the operating instructions supplied with the Bluetooth mobile phone.
    Status (call) button
    Standby
    Press once to start voice dial (voice dial compatible mobile phones only).
    Press for about 2 seconds to redial the phone number that is dialed last time.
    Outgoing call
    Press once to cancel outgoing call.
    Press for about 2 seconds to change call device between the system and mobile phone.
    Incoming call
    Press once to answer call.
    Press for about 2 seconds to reject call.
    During call
    Press once to finish call.
    Press for about 2 seconds to change call device between the system and mobile phone.
    Using Hands-free Calling with Another Bluetooth Mobile Phone While Listening to
    Music
    This system supports Multipoint technology. You can enjoy hands-free calling with another Bluetooth mobile phone while listening to
    music with a Bluetooth music player.
    One touch connection (NFC) cannot be used in this procedure.
    Operations may vary depending on the Bluetooth device. This type of Bluetooth connection may not be established depending on
    the combination of the Bluetooth devices. Refer also to the operating instructions supplied with your Bluetooth devices.
    1 Make the Bluetooth connections between the system and a Bluetooth music player via A2DP, and
    between the system and a Bluetooth mobile phone via HFP or HSP.
    For details on the Bluetooth connection procedure, see “How to Make Wireless Connection with Bluetooth Devices. When the
    Bluetooth connection is established, the (Bluetooth) indicator (blue) on the system stays on.
    Tips
    To use only the calling function of a
    Bluetooth mobile phone that also has a music function, establish Bluetooth connection between the
    system and the mobile phone via HFP or HSP, not via A2DP.
    Depending on the
    Bluetooth mobile phone, while the Bluetooth connection is established via HFP or HSP, the other Bluetooth connection
    via A2DP may also be occupied by the same Bluetooth mobile phone. A Bluetooth music player cannot be connected with this system in
    this case.
    Note
    To make the same connection with the same devices after turning the system off, follow this procedure again.
    Listening to Music by Wired Connection with a Portable
    Audio Device, etc.
    1 Connect the device to the system.
    Connecting cord (not supplied)
    (Stereo mini jack)
    2 Turn on the system.
    3 Start playback on the connected device, then adjust the volume.
    Set the volume of the connected device to a moderate level, and press the VOLUME –/+ buttons on the system.
    Notes
    When connecting cord (not supplied) is used with this system, the source device switches to the one connected by the cord automatically,
    even if you are listening to music via the Bluetooth connection.
    You cannot listen to music via the
    Bluetooth connection while a connecting cord (not supplied) is used with this system. After use, disconnect
    it.
    Tips
    You can use hands-free calling while a connecting cord (not supplied) is used with this system.
    When connected with a source device via a connecting cord (not supplied), not via a
    Bluetooth connection, and playback has been stopped for
    about 20 minutes, the system turns off automatically.
    Battery compartment
    (bottom of the system)
    Handle
    / button
    BLUETOOTH
    PAIRING button
    Top of the system
    (call) button
    OPR/BATT
    indicator (green)
     (play/
    pause) button
    N-mark VOLUME
    −/+ button
    (Bluetooth) indicator (blue)
    Microphone
    Rear of the system
    DC IN 6V jack AUDIO IN jack
    Troubleshooting
    No sound / Sound from only one speaker /
    Low sound level
    Check that both this system and
    the connected device are turned
    on.
    If you are connecting a personal
    computer to the system, make
    sure the audio output setting of
    the computer is set for a Bluetooth
    device.
    Turn up the volume of the system
    and the connected device.
    Pair this system and the Bluetooth
    device again.
    Check that the connected device
    is being played back.
    If the connected device is monaural,
    sound will only be output from the
    left speaker.
    Check that both plugs of the
    connecting cord (not supplied)
    are firmly inserted into the system
    and the connected device.
    Distorted sound /
    Humming or noise in the system output
    Turn down the volume of the
    connected device.
    Keep the system away from a TV.
    If the connected device has an
    equalizer function, set it to off.
    Switch the Bluetooth connection to
    A2DP by operating the Bluetooth
    device when HFP or HSP is set.
    Keep the system away from a
    microwave oven, wireless LAN,
    etc.
    If the OPR/BATT indicator (green) is
    dim, replace all the batteries with
    new ones.
    Bring this system and the
    Bluetooth device closer together.
    Remove any obstacle between
    this system and the Bluetooth
    device.
    If you connect a device with a built-
    in radio or tuner to this system,
    broadcasts may not be received, or
    sensitivity may be reduced. Locate
    the system farther away from the
    device and check that you can listen
    to the broadcasts satisfactorily.
    Pairing is not possible
    Bring this system and the
    Bluetooth device to within 1 m of
    each other.
    If the (Bluetooth) indicator (blue)
    is not flashing quickly, press and
    hold the BLUETOOTH PAIRING
    button on the system until beeps
    are heard.
    No voice / Low voice from recipient
    Check that both this system and
    the connected device are turned
    on.
    Select HFP or HSP Bluetooth
    connection by operating the
    Bluetooth device.
    Check that output of the
    Bluetooth mobile phone is set for
    the system.
    Turn up the volume of the system
    and the connected device.
    One touch connection (NFC) is
    not possible
    Keep the smartphone close to the
    system until the smartphone
    vibrates. If you fail, move the
    smartphone slightly on the N
    marked part of the system.
    If the smartphone is in a case,
    remove it.
    Check that the NFC function of
    the smartphone is set to on.
    NFC receiving sensitivity depends
    on the device. If you fail to connect
    with a smartphone by One touch
    several times, connect to the
    system by on-screen operation.
    Check that the “NFC Easy
    Connect” app is displayed on the
    smartphone.
    What is Bluetooth wireless
    technology?
    Bluetooth wireless technology is a short-range wireless
    technology that enables wireless data communication between
    digital devices, such as a computer and digital camera. Bluetooth
    wireless technology operates within a range of about 10 m.
    Connecting two devices as necessary is common, but some
    devices can be connected to multiple devices at the same time.
    You do not need to use a cable for connection, nor is it necessary
    for the devices to face one another, such is the case with infrared
    technology. For example, you can use such a device in a bag or
    pocket.
    Bluetooth standard is an international standard supported by
    thousands of companies all over the world, and employed by
    various companies worldwide.
    Communication System and Compatible
    Bluetooth Profiles of the system
    Profile is standardisation of the function for each Bluetooth
    device specification. The system supports the following
    Bluetooth version and profiles:
    Communication System:
    Bluetooth Specification version 3.0
    Compatible Bluetooth Profiles:
    A2DP (Advanced Audio Distribution Profile): Transmitting or
    receiving audio content of high-quality.
    AVRCP (Audio Video Remote Control Profile): Controlling A/V
    equipment; pausing, stopping, or starting playback, etc.
    HSP (Headset Profile): Talking on the phone/Operating the
    phone.
    HFP (Hands-free Profile): Talking on the phone/Operating the
    phone by hands-free.
    Maximum communication range
    Use Bluetooth devices within 10 m (line of sight) of the system.
    Maximum communication range may shorten under the
    following conditions.
    There is an obstacle such as a person, metal, or wall between
    the system and Bluetooth device.
    A wireless LAN device is in use near the system.
    A microwave oven is in use near the system.
    A device that generates electromagnetic radiation is in use
    near the system.
    Interference from other devices
    Because Bluetooth devices and wireless LAN (IEEE802.11b/g) use
    the same frequency, microwave interference may occur and
    resulting in communication speed deterioration, noise, or invalid
    connection if the system is used near a wireless LAN device. In
    such a case, perform the following.
    Use the system at least 10 m away from the wireless LAN
    device.
    If the system is used within 10 m of a wireless LAN device,
    turn off the wireless LAN device.
    Interference to other devices
    Microwaves emitting from a Bluetooth device may affect the
    operation of electronic medical devices. Turn off the system and
    other Bluetooth devices in the following locations, as it may
    cause an accident.
    where inflammable gas is present, in a hospital, train,
    airplane, or a gas station
    near automatic doors or a fire alarm
    Notes
    To be able to use the Bluetooth function, the Bluetooth device
    to be connected requires the same profile as the system’s.
    Note also that even if the same profile exists, devices may vary
    in function depending on their specifications.
    Due to the characteristic of Bluetooth wireless technology, the
    sound played on the system is slightly delayed from the sound
    played on the Bluetooth device during talking on the
    telephone or listening to the music.
    This system supports security capabilities that comply with
    the Bluetooth standard to provide a secure connection when
    the Bluetooth wireless technology is used, but security may
    not be enough depending on the setting. Be careful when
    communicating using Bluetooth wireless technology.
    We do not take any responsibility for the leakage of
    information during Bluetooth communication.
    A device featuring the Bluetooth function is required to
    conform to the Bluetooth standard specified by Bluetooth SIG,
    and be authenticated. Even if the connected device conforms
    to the above mentioned Bluetooth standard, some devices
    may not be connected or work correctly, depending on the
    features or specifications of the device.
    Noise or sound skips may occur depending on the Bluetooth
    device connected with the system, the communication
    environment or the usage environment.
    Specifications
    Speaker section
    Speaker system 50 mm
    Enclosure type Bass reflex
    Amplifier section
    Reference output power
    2 W + 2 W (10 % T.H.D., 1 kHz, 6 Ω)
    Input Stereo mini jack × 1
    Bluetooth
    Communication System
    Bluetooth Specification version 3.0
    Output
    Bluetooth Specification Power Class 2
    Maximum communication range
    Line of sight approx. 10 m*
    1
    Frequency band 2.4 GHz band (2.4000 GHz - 2.4835 GHz)
    Modulation method
    FHSS
    Compatible Bluetooth Profiles*
    2
    A2DP (Advanced Audio Distribution Profile)
    AVRCP (Audio Video Remote Control Profile)
    HSP (Headset Profile)
    HFP (Hands-free Profile)
    Supported Codec*
    3
    SBC*
    4
    Transmission range (A2DP)
    20 Hz - 20,000 Hz (Sampling frequency
    44.1 kHz)
    *
    1
    The actual range will vary depending on factors such as
    obstacles between devices, magnetic fields around a
    microwave oven, static electricity, reception sensitivity, aerial’s
    performance, operating system, software application, etc.
    *
    2
    Bluetooth standard profiles indicate the purpose of Bluetooth
    communication between devices.
    *
    3
    Codec: Audio signal compression and conversion format
    *
    4
    Subband Codec
    Microphone
    Type: Electret condenser
    Direction characteristic:
    Omni directional
    Effective frequency range:
    200 Hz – 3,600 Hz
    Operating temperature:
    0 °C to 45 °C
    General
    Power DC 6 V (when using the supplied AC adaptor
    connected to AC 230 V, 50 Hz power supply)
    or 4 alkaline LR6 (size AA) batteries
    Rated power consumption
    6 W (when using the supplied AC adaptor)
    Approx. 0.2 W (in standby mode when using
    the supplied AC adaptor)
    Battery life (when using the Bluetooth connection)
    Sony alkaline battery LR6 (size AA):
    approx. 20 hours*
    5
    Sony nickel metal hydride rechargeable
    battery NHAAB2K (size AA):
    approx. 20 hours*
    5
    Dimensions Approximately 245 mm × 185 mm × 88 mm
    (w/h/d)
    Mass Approximately 1,060 g including batteries
    Supplied accessories
    AC adaptor (1)
    Operating Instructions (this document) (1)
    Safety information
    *
    5
    Time may vary, depending on the temperature or conditions
    of use.
    Design and specifications are subject to change without notice.
Sony SRS-BTM8

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Sony SRS-BTM8 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Sony SRS-BTM8 responder adecuadamente a su pregunta.

Vea el manual de Sony SRS-BTM8 aquí, de forma gratuita. Este manual pertenece a la categoría Altavoces Dock y ha sido calificado por 1 personas con un promedio de 6.6. Este manual está disponible en los siguientes idiomas: Inglés, Francia. ¿Tiene alguna pregunta sobre Sony SRS-BTM8 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Sony SRS-BTM8

General
Marca Sony
Modelo SRS-BTM8
Producto Altavoz Dock
EAN 4905524895223
Idioma Inglés, Francia
Tipo de archivo PDF
Altavoces
Canales de salida de audio 2.0canales
Número de altavoces 1
Número de dispositivos 2
Diámetro del conductor 50mm
Tipo de altavoces De 2 vías
Desempeño
Uso recomendado mobile phone/smartphone
Ampificador -
Ecualizador
Operado remotamente
Radio FM
Audio
Potencia estimada RMS 4W
Rango de frecuencia 20 - 20000Hz
Obstrucción -
Diseño
Color del producto Negro
Pantalla incorporada
Tipo de producto Altavoz portátil estéreo
Otras características
Dimensiones (Ancho x Profundidad x Altura) 245 x 88 x 185mm
Control de energía
Adaptador de energía externo
Tipo de batería AA
Numero de baterías soportadas 4
Autonomía 20h
Tecnología de batería Alcali✗
Alimentación Batería
Consumo energético 6W
Puertos e Interfaces
Tecnología de conectividad Inalámbrico
Entrada de CA
Perfiles de Bluetooth A2DP, AVRCP, HFP, HSP
Alcance de frecuencia 2.4GHz
Versión de Bluetooth 3.0+HS
AirPlay
Bluetooth
Comunicación de Campo Cercano (NFC)
- NFC/Bluetooth
Peso y dimensiones
Ancho 245mm
Profundidad 88mm
Altura 185mm
Peso 1060g
Contenido del embalaje
Tarjeta de garantía
Guía de instalación rápida
Cables incluidos Corriente alterna

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más