Sony SRS-BTV25

Sony SRS-BTV25 manual

(1)
  • SRS-BTV25 [EU8]
    4-298-825
    -13(1)
    Wireless Speaker System
    4-298-825-13(1)
    SRS-BTV25
    ©2011 Sony Corporation Printed in China
    Low sound level
    
    Turn up the volume of the source device as high as
    possible to the extent that sound is not distorted. For
    details on volume adjustment, refer to the operating
    instructions supplied with the device.
    
    Turn up the volume of the system.
    Distorted sound
    
    Turn down the volume of the source device to the point
    where the sound is no longer distorted. For details on
    volume adjustment, refer to the operating instructions
    supplied with the device.
    
    If the source device has a bass boosts function, turn it
    off.
    
    Turn down the volume of the system.
    There is hum or noise in the speaker output.
    
    Make sure all the connections have been correctly made.
    
    Make sure none of the audio devices are positioned too
    close to the TV set.
    The brightness of the POWER indicator (green) is
    unstable.
    
    The brightness of the POWER indicator (green) may
    become unstable when the volume is turned up. This is
    not malfunction.
    When using the Bluetooth connection
    No sound
    
    Ensure that this system is not too far from the Bluetooth
    stereo audio source device, and that this system is not
    receiving interference from a wireless LAN, another 2.4
    GHz wireless device, or a microwave oven.
    
    Check that the Bluetooth connection is made properly
    between this system and the Bluetooth stereo audio
    source device.
    
    Pair this system and the Bluetooth stereo audio source
    device again.
    
    If you are pairing this system and a personal computer,
    make sure the audio output setting of the computer is
    set for a Bluetooth device.
    Sound skips or the communication is interrupted.
    
    If a device that generates electromagnetic radiation,
    such as a wireless LAN, other Bluetooth device(s), or a
    microwave oven is nearby, move away from such
    sources.
    
    Remove any obstacle between this system and other
    Bluetooth device, or move away from the obstacle.
    
    Locate this system and other Bluetooth device(s) as near
    as possible to each other.
    
    Re-position this system.
    
    Re-position the other Bluetooth device.
    Pairing is not possible.
    
    Bring this system and the Bluetooth device closer
    together.
    
    Make sure pairing mode is activated.
    USB charging problem
    The device cannot be charged.
    
    Make sure the AC adaptor is connected to a wall outlet
    (mains).
    
    Refer to the operating instructions supplied with the
    device for the charging procedure.
    Specifications
    Speaker section
    Speaker system
    Woofer: 56 mm, magnetically shielded
    Tweeter: 20 mm
    Enclosure type
    Bass reflex
    Impedance
    Woofer: 6 Ω
    Tweeter: 6 Ω
    Amplifier section
    Reference output power
    13 W (10% T.H.D., 1 kHz, 6 Ω)
    Input Stereo mini jack × 1
    Input impedance
    4.7 kΩ (at 1 kHz)
    Bluetooth
    Communication System
    Bluetooth Specification version 2.1 + EDR
    (Enhanced Data Rate)
    Output
    Bluetooth Specification Power Class 2
    Maximum communication range
    Line of sight approx. 10 m*
    1
    Frequency band
    2.4 GHz band (2.4000 GHz - 2.4835 GHz)
    Modulation method
    FHSS
    Compatible Bluetooth Profiles*
    2
    A2DP (Advanced Audio Distribution Profile)
    AVRCP 1.3 (Audio Video Remote Control
    Profile)
    Supported Codec*
    3
    SBC*
    4
    Supported content protection method
    SCMS-T
    Transmission range (A2DP)
    20 Hz - 20,000 Hz (Sampling frequency 44.1
    kHz)
    *1 The actual range will vary depending on factors such
    as obstacles between devices, magnetic fields around a
    microwave oven, static electricity, reception sensitivity,
    aerial’s performance, operating system, software
    application, etc.
    *2
    Bluetooth standard profiles indicate the purpose of
    Bluetooth communication between devices.
    *3 Codec: Audio signal compression and conversion
    format
    *4 Subband Codec
    USB
    USB jack
    Type A (for charging the battery of a connected
    device) (5 V, 500 mA)
    General
    Power DC 13 V
    Rated power consumption
    12 W
    Operating temperature
    5 ºC - 35 ºC
    Power voltage
    100 V - 240 V AC
    Dimensions (w/h/d)
    Approximately 145 mm × 145 mm × 145 mm
    Mass Approximately 500 g
    English
    Before operating the system, please read this guide thoroughly
    and retain it for future reference.
    WARNING
    To reduce the risk of fire or electric shock, do not expose
    this apparatus to rain or moisture.
    To reduce the risk of electrical shock, do not open the
    cabinet. Refer servicing to qualified personnel only.
    Do not install the appliance in a confined space, such as a
    bookcase or built-in cabinet.
    To reduce the risk of fire, do not cover the ventilation
    opening of the apparatus with newspapers, tablecloths,
    curtains, etc. Do not place the naked flame sources such as
    lighted candles on the apparatus.
    To reduce the risk of fire or electric shock, do not expose
    this apparatus to dripping or splashing, and do not place
    objects filled with liquids, such as vases, on the apparatus.
    Do not install the AC adaptor in a confined space, such as
    a bookcase or built-in cabinet.
    As the main plug is used to disconnect the unit from the
    mains, connect the unit to an easily accessible AC outlet.
    Should you notice an abnormality in the unit, disconnect
    the main plug from AC outlet immediately.
    The system is not disconnected from the mains as long as
    it is connected to the AC outlet, even if the system itself
    has been turned off.
    The nameplate is located on the bottom exterior of the
    system.
    Hereby, Sony Corp., declares that this equipment is in
    compliance with the essential requirements and other
    relevant provisions of Directive 1999/5/EC.
    For details, please access the following URL:
    http://www.compliance.sony.de/
    Norway: Use of this radio equipment is not allowed in the
    geographical area within a radius of 20 km from the centre
    of Ny-Ålesund, Svalbard.
    Italy: Use of the RLAN network is governed:
    with respect to private use, by the Legislative Decree of
    1.8.2003, no. 259 (“Code of Electronic Communications”).
    In particular Article 104 indicates when the prior
    obtainment of a general authorization is required and Art.
    105 indicates when free use is permitted;
    with respect to the supply to the public of the RLAN access
    to telecom networks and services, by the Ministerial Decree
    28.5.2003, as amended, and Art. 25 (general authorization
    for electronic communications networks and services) of
    the Code of electronic communications
    On Copyrights and Licenses
    The Bluetooth
    ®
    word mark and logos are owned by the
    Bluetooth SIG, Inc. and any use of such marks by Sony
    Corporation is under license.
    Other trademarks and trade names are those of their
    respective owners.
    Notice for customers: the following information
    is only applicable to equipment sold in countries
    applying EU directives
    The manufacturer of this product is Sony Corporation, 1-
    7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The
    Authorized Representative for EMC and product safety is
    Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
    Stuttgart, Germany. For any service or guarantee matters
    please refer to the addresses given in separate service or
    guarantee documents.
    Disposal of Old Electrical &
    Electronic Equipment (Applicable in
    the European Union and other
    European countries with separate
    collection systems)
    This symbol on the product or on its packaging indicates
    that this product shall not be treated as household waste.
    Instead it shall be handed over to the applicable collection
    point for the recycling of electrical and electronic
    equipment. By ensuring this product is disposed of
    correctly, you will help prevent potential negative
    consequences for the environment and human health,
    which could otherwise be caused by inappropriate waste
    handling of this product. The recycling of materials will
    help to conserve natural resources. For more detailed
    information about recycling of this product, please contact
    your local Civic Office, your household waste disposal
    service or the shop where you purchased the product.
    Precautions
    Notes when using with a mobile phone
    
    You cannot use this unit to talk over the telephone, even
    if the Bluetooth connection between this unit and a
    mobile phone is made.
    
    For details on operation of your mobile phone when
    receiving a telephone call while transmitting the sound
    using the Bluetooth connection, refer to the operating
    instructions supplied with the mobile phone.
    On safety
    The nameplate indicating Sony trademark, model number
    and electrical rating is located on the bottom exterior of
    this unit.
    
    Before operating the system, be sure that the operating
    voltage of the system is identical with that of your local
    power supply.
    Where purchased Operating voltage
    All countries/regions 100 – 240 V AC, 50/60 Hz
    
    Use only the supplied AC adaptor.
    On placement
    
    Do not set the speaker in an inclined position.
    
    Do not leave the system in a location near heat sources,
    or in a place subject to direct sunlight, excessive dust,
    moisture, rain or mechanical shock.
    On operation
    
    Do not insert any small objects, etc., into the jacks or
    ventilation hole on the rear of the system. The system
    may short out or malfunction.
    
    Do not open the cabinet. Refer servicing to qualified
    personnel only.
    
    Should any solid object or liquid fall into the system,
    have the system checked by qualified personnel before
    operating it any further.
    
    Although this system is magnetically shielded, do not
    leave recorded tapes, watches, personal credit cards, or
    floppy disks with magnetic coding in front of the system
    for an extended period of time.
    On cleaning
    
    Do not use alcohol, benzine, or thinner to clean the
    cabinet.
    If the TV picture or monitor display is
    magnetically distorted
    
    Although this system is magnetically shielded, there
    may be cases that the picture on some TV sets/personal
    computer sets may become magnetically distorted. In
    such a case, turn off the power of the TV set/personal
    computer set once, and after 15 to 30 minutes turn it on
    again.
    For the personal computer set, take the appropriate
    measures such as data storage before turning it off.
    When there seems to be no improvement, locate the
    system further away from the TV set/personal computer
    set.
    Furthermore, be sure not to place objects in which
    magnets are attached or used near the TV set/personal
    computer set, such as audio racks, TV stands, toys etc.
    These may cause magnetic distortion to the picture due
    to their interaction with the system.
    Others
    
    If you have any questions or problems concerning this
    unit that are not covered in this manual, please consult
    your nearest Sony dealer.
    
    Should any problem persist, consult your nearest Sony
    dealer.
    Troubleshooting
    If you run into any problems using this system, use the
    following checklist. Should any problem persist, consult
    your nearest Sony dealer.
    Common Problems
    No sound
    
    Check that both this system and the source device are
    turned on.
    
    Turn up the volume of the system.
    
    Turn up the volume of the source device as high as
    possible to the extent that sound is not distorted. For
    details on volume adjustment, refer to the operating
    instructions supplied with the device.
    
    Make sure all the connections have been correctly made.
    
    Make sure the source device is playing.
    Firmly connect the supplied AC adaptor to the DC IN 13V
    jack on the back of the system, and plug the AC power
    cord (mains lead) into a wall outlet (mains).
    to wall outlet
    (mains)
    to DC IN 13V jack
    Rear of the system
    AC adaptor (supplied)
    Notes on the AC adaptor and AC power cord
    (mains lead)
    When connecting or disconnecting the AC power cord
    (mains lead), turn off the system beforehand.
    Otherwise, it may cause malfunction.
    Use only the supplied AC adaptor. To avoid damaging
    the system, do not use any other AC adaptor.
    Polarity of the plug
    Plug the AC power cord (mains lead) into a nearby wall
    outlet (mains). In the case of a problem, unplug it from
    the wall outlet (mains) immediately.
    Do not place the AC adaptor on a bookshelf or in a
    confined place, such as a cabinet.
    To avoid fire or electric shock, do not use the AC
    adaptor in a place near liquid or subject to moisture.
    Furthermore, do not place liquid-filled vessels, such as
    vases, etc., on the AC adaptor.
    The supplied AC adaptor and AC power cord (mains
    lead) are only for this system. Do not use them with any
    other device.
    In system protect mode, all indicators flash, and the
    system buttons will not work. To exit this mode,
    disconnect the AC power cord (mains lead) from the
    wall outlet (mains), then connect again. Make sure all
    indicators are off, and turn on the system. If the system
    detects a problem (indicators flashing repeatedly, no
    sound from connected device, etc.), there may be a
    malfunction. In this case, immediately disconnect the
    AC power cord (mains lead) and seek repair.
    To turn the system on/off
    Press /.
    To charge the device
    Connect the AC adaptor to a wall outlet (mains), and
    connect the device to the system using the USB cable
    supplied with the device.
    Charging begins automatically, whether the system is
    turned on or off. The charging status is displayed on the
    device. For details, refer to the operating instructions
    supplied with the device.
    Side of the system
    to USB jack
    USB cable supplied with the device
    USB rechargeable
    devices such as mobile
    phone, WALKMAN, etc.
    Using the Bluetooth
    Connection
    By using the Bluetooth connection, you can listen to the
    sound from a Bluetooth device with the system wirelessly.
    Note
    For details on how to operate the device to be
    connected, refer to the operating instructions supplied
    with the device.
    On pairing
    Bluetooth devices need to be “paired” with each other
    beforehand.
    Once Bluetooth devices are paired, there is no need for
    pairing again, except in the following cases:
    Pairing information is deleted after repair, etc.
    The system is paired with 10 or more devices.
    The system can be paired with up to 9 Bluetooth stereo
    audio source devices. If a new device is paired after 9
    devices have been paired, the device whose latest
    connection time is the oldest among the 9 paired
    devices is replaced by the new one.
    The system is initialised.
    All pairing information is deleted.
    Pairing with a source device
    Check the following before operating the system.
    The system is connected to a power source.
    The operating instructions supplied with the device are
    kept at hand.
    1 Press the / button to turn on the system.
    The POWER indicator (green) lights up.
    2 Press and hold the BLUETOOTH PAIRING
    button for any more than 2 seconds.
    When the (BLUETOOTH) indicator (blue) starts
    flashing quickly, release the button. The system enters
    pairing mode.
    Note
    Pairing mode is cancelled and the system is turned
    off after about 5 minutes. If the pairing mode is
    cancelled while performing this procedure, start
    over from step 2.
    3 Perform the pairing procedure on the
    Bluetooth device to detect the system.
    A list of detected devices appears on the display of the
    Bluetooth stereo audio source device.
    This system is displayed as “SRS-BTV25.
    If “SRS-BTV25” is not displayed, repeat from step 2.
    Tip
    If pairing information has not been memorised, the
    system enters pairing mode automatically when the
    BLUETOOTH PAIRING button is pressed. There is
    no need to hold the BLUETOOTH PAIRING
    button for any more than 2 seconds.
    Notes
    When pairing, be sure to place both the Bluetooth
    devices within 1 m of each other.
    Some devices cannot display a list of detected
    devices.
    4 Select “SRS-BTV25” shown in the display of
    the Bluetooth device.
    5 If Passcode* input is required on the display
    of the Bluetooth device, input “0000.
    * Passcode may be called “Passkey,” “PIN code,” “PIN
    number,” or “Password.
    6 Start the Bluetooth connection from the
    Bluetooth device.
    The system memorises the device as the last connected
    device. Some Bluetooth devices may connect with the
    system automatically when pairing is complete.
    Tip
    To pair with other Bluetooth devices, repeat steps 2
    to 5 for each device.
    Note
    Passcode of the system is fixed as “0000.” The system
    cannot be paired with a Bluetooth device whose
    Passcode is not “0000.
    Listening to the system
    The system supports SCMS-T content protection. You can
    enjoy music, etc., from a device such as a mobile phone or
    portable TV that supports SCMS-T content protection.
    Check the following before operating the system.
    The Bluetooth devices Bluetooth function is on.
    Pairing of the system and the Bluetooth device is
    complete.
    1 Press the / button to turn on the system.
    The POWER indicator (green) lights up.
    2 Press the BLUETOOTH PAIRING button.
    Note
    If the (BLUETOOTH) indicator (blue) is
    activated, this step is not required.
    3 Start the Bluetooth connection from the
    Bluetooth device.
    4 Start playback on the Bluetooth device.
    Note
    If the source device has a bass boost function or
    equaliser function, turn them off. If these functions
    are on, sound may be distorted.
    5 Adjust the volume.
    Set the volume of the Bluetooth device to a moderate
    level, and press the VOL –/+ buttons on the system.
    Tips
    You can adjust the volume of the system via a
    Bluetooth device supporting AVRCP (Audio/Visual
    Remote Control Profile) VOLUME UP/DOWN. For
    details, refer to the operating instructions supplied
    with the device.
    The volume of the system may not be controllable,
    depending on the device.
    Note
    The POWER indicator (green) flashes three times
    when the volume is set to minimum or maximum.
    Notes
    In the following cases, you need to make the Bluetooth
    connection again.
    – The power of the system does not turn on.
    – The power of the
    Bluetooth device does not turn on,
    or the Bluetooth function is off.
    – The
    Bluetooth connection is not made.
    When the sound of a Bluetooth device is being
    reproduced using the Bluetooth connection (when both
    the POWER indicator (green) and (BLUETOOTH)
    indicator (blue) light up), the sound from a device
    connected to the AUDIO IN jack cannot be heard. Press
    the AUDIO IN button to listen to the sound from a
    device connected to the AUDIO IN jack.
    If more than one device paired with the system is being
    played back, sound will be heard from just one of those
    devices.
    To finish listening
    Terminate the Bluetooth connection by any of the
    operations below.
    Operate the Bluetooth device to terminate the
    connection. For details, refer to the operating
    instructions supplied with the device.
    Turn off the Bluetooth device.
    Turn off the system.
    Indications of the Bluetooth
    function
    Status
    (BLUETOOTH)
    indicator (blue)
    Pairing with a device Flashes quickly
    Searching for a device Flashes
    Connecting to a device Lights up
    Activating the Bluetooth
    standby function
    Flashes slowly*
    Deactivating the Bluetooth
    standby function
    Off
    Receiving audio signal from
    the AUDIO IN jack.
    Off
    * Even when the Bluetooth standby function is activated,
    the indicator will be off if there is no pairing
    information.
    To use the Bluetooth standby
    function
    By using the Bluetooth standby function, you can make the
    system turn off temporarily and wait for the Bluetooth
    connection.
    1 Hold the BLUETOOTH PAIRING button
    and press the / button for any more than 2
    seconds while the system is turned on.
    The system turns off and the (BLUETOOTH)
    indicator (blue) flashes.
    If you start the Bluetooth connection, the system turns
    on automatically and starts communication.
    Tip
    When waiting for the Bluetooth connection, you can
    reduce power consumption by using the Bluetooth
    standby function, rather than leaving the system turned
    on.
    Note
    To disable the Bluetooth standby function, perform step
    1 again. (The (BLUETOOTH) indicator (blue) and
    the system will turn off.)
    Using by a wired connection
    You can listen to the sound from a device connected to the
    AUDIO IN jack.
    Note
    For details on how to operate the device to be
    connected, refer to the operating instructions supplied
    with the device.
    Hooking up the system
    RK-G136 connecting
    cord (optional)
    Portable audio device,
    computer, etc.
    Rear of the system
    To headphone
    jack (stereo mini
    jack)
    to AUDIO IN jack
    1 Connect the device to the system.
    To connect to a stereo phone-type headphone
    jack
    Use the optional connecting cord RK-G136 and plug
    adaptor PC-234S, or optional connecting cords RK-G136
    and RK-G138.*
    * The above optional accessories may not be available in
    some areas.
    Listening to the system
    1 Press the / button to turn on the system.
    The POWER indicator (green) lights up.
    2 Press the AUDIO IN button.
    Note
    If the AUDIO IN indicator (amber) is activated, this
    step is not required.
    3 Start playback on the source device.
    4 Adjust the volume.
    Set the volume of the source device to a moderate
    level, and press the VOL –/+ buttons on the system.
    Note
    The POWER indicator (green) flashes three times
    when the volume is set to minimum or maximum.
    5 Press the / button to turn off the system
    after use.
    The POWER indicator (green) turns off.
    Operations
    Function of parts
    / button
    Turns the system on/off. The POWER indicator (green)
    lights up when the system is turned on.
    VOL (volume) −/+ button
    Adjusts the volume.
    The POWER indicator (green) flashes three times when
    the volume is set to minimum or maximum.
    BOOST button
    Press to obtain a heavy bass sound effect. The BOOST
    indicator (amber) lights up. To disable the effect, press the
    button again (the indicator turns off).
    The default setting of the function is on. Turn it off if
    desired.
    BLUETOOTH PAIRING button
    Press to use the Bluetooth connection or pair with a
    Bluetooth device.
    Depending on the communication status, the
    (BLUETOOTH) indicator (blue) lights up or flashes. For
    details about the flashing patterns of the
    (BLUETOOTH) indicator (blue), see “Indications of the
    Bluetooth function” in these operating instructions.
    AUDIO IN button
    Press to receive audio signal from the AUDIO IN jack. The
    AUDIO IN indicator (amber) lights up.
    AUDIO IN jack
    Connects to the headphone jack of a computer, portable
    audio device, etc.
    DC IN 13V jack
    Connects the supplied AC adaptor.
    USB jack
    Charges a device connected to the system by the USB
    cable. This jack is used for charging the connected device
    only. Audio signal, etc., cannot be sent via this jack.
    Features
    This product is a wireless speaker system that uses
    Bluetooth wireless technology.
    
    Enjoy music wirelessly from Bluetooth stereo enabled
    music players, mobile phones and PC’s.*
    
    Bluetooth Version 2.1 + EDR (Enhanced Data Rate) for
    higher quality audio with less interference.
    
    Powerful sound with 13 W amplifiers and MegaBass.
    
    Includes one analogue input for direct connection from
    a music player or other audio device.
    
    Magnetically-shielded design for use near your TV or
    monitor.
    
    USB-charge compliant devices, e.g., mobile phones,
    “WALKMAN,” etc., can be charged via the USB jack of
    this product.
    Enjoying listening to sound wirelessly by
    Bluetooth wireless technology
    You can enjoy listening to sound wirelessly by connecting
    Bluetooth supported devices (such as a mobile phone,
    digital music player, digital music player connected to a
    Bluetooth transmitter, or personal computer)* to the
    system. The system receives stereo audio signals from the
    source device.
    Bluetooth device.
    * Bluetooth devices to be connected with the system are
    required to support A2DP (Advanced Audio
    Distribution Profile).
    Power source
    Note on the power management system
    After playback has finished, if no operation is performed
    for 20 minutes, the system will automatically turn off.
    Notes
    If the speaker is connected to a device with a built-in
    radio or tuner, radio stations may not be received, or
    sensitivity may be reduced significantly.
    If the source device has a bass boost function or
    equaliser function, turn them off. If these functions are
    on, sound may be distorted.
    To switch the connection to the Bluetooth connection,
    press the BLUETOOTH PAIRING button.
    Initialising the System
    You can reset the system to its default and delete all
    pairing information.
    1 Hold the BOOST button and press the
    BLUETOOTH PAIRING button for any more
    than 5 seconds while the system is turned on.
    The POWER indicator (green) flashes for 2 seconds.
    What is Bluetooth wireless
    technology?
    Bluetooth wireless technology is a short-range wireless
    technology that enables wireless data communication
    between digital devices, such as a computer and digital
    camera. Bluetooth wireless technology operates within a
    range of about 10 metres.
    Connecting two devices as necessary is common, but
    some devices can be connected to multiple devices at the
    same time.
    You do not need to use a cable for connection, nor is it
    necessary for the devices to face one another, such is the
    case with infrared technology. For example, you can use
    such a device in a bag or pocket.
    Bluetooth standard is an international standard supported
    by thousands of companies all over the world, and
    employed by various companies worldwide.
    Communication System and Compatible
    Bluetooth Profiles of the system
    Profile is standardisation of the function for each
    Bluetooth device specification. The system supports the
    following Bluetooth version and profiles:
    Communication System:
    Bluetooth Specification version 2.1 + EDR*
    Compatible Bluetooth Profiles:
    – A2DP (Advanced Audio Distribution Profile):
    Transmitting or receiving audio content of high-
    quality.
    – AVRCP 1.3 (Audio Video Remote Control Profile):
    Controlling the sound volume.
    * Enhanced Data Rate
    Maximum communication range
    Use Bluetooth devices within 10 m (line of sight) of the
    system.
    Maximum communication range may shorten under the
    following conditions.
    – There is an obstacle such as a person, metal, or wall
    between the system and Bluetooth device.
    – A wireless LAN device is in use near the system.
    – A microwave oven is in use near the system.
    – A device that generates electromagnetic radiation is
    in use near the system.
    Interference from other devices
    Because Bluetooth devices and wireless LAN
    (IEEE802.11b/g) use the same frequency, microwave
    interference may occur and resulting in communication
    speed deterioration, noise, or invalid connection if the
    system is used near a wireless LAN device. In such a case,
    perform the following.
    – Use the system at least 10 m away from the wireless
    LAN device.
    – If the system is used within 10 m of a wireless LAN
    device, turn off the wireless LAN device.
    Interference to other devices
    Microwaves emitting from a Bluetooth device may affect
    the operation of electronic medical devices. Turn off the
    system and other Bluetooth devices in the following
    locations, as it may cause an accident.
    – where inflammable gas is present, in a hospital, train,
    airplane, or a gas station
    – near automatic doors or a fire alarm
    Notes
    To be able to use the Bluetooth function, the Bluetooth
    device to be connected requires the same profile as the
    systems.
    Note also that even if the same profile exists, devices
    may vary in function depending on their specifications.
    Due to the characteristic of Bluetooth wireless
    technology, the sound played on the system is slightly
    delayed from the sound played on the Bluetooth device
    during talking on the telephone or listening to the
    music.
    This system supports security capabilities that comply
    with the Bluetooth standard to provide a secure
    connection when the Bluetooth wireless technology is
    used, but security may not be enough depending on the
    setting. Be careful when communicating using Bluetooth
    wireless technology.
    We do not take any responsibility for the leakage of
    information during Bluetooth communication.
    A device featuring the Bluetooth function is required to
    conform to the Bluetooth standard specified by
    Bluetooth SIG, and be authenticated. Even if the
    connected device conforms to the above mentioned
    Bluetooth standard, some devices may not be connected
    or work correctly, depending on the features or
    specifications of the device.
    Noise or sound skips may occur depending on the
    Bluetooth device connected with the system, the
    communication environment or the usage environment.
    USB jack*
    Top of the system
    VOL −/+ button
    (BLUETOOTH) indicator
    AUDIO IN indicator
    Side of the system
    BOOST
    button
    Parts and controls
    BLUETOOTH
    PAIRING button
    AUDIO IN
    button
    Rear of the system
    / button
    POWER indicator
    BOOST indicator
    The VOL + button has a
    tactile dot.
    * For charging only
    AUDIO IN
    jack
    DC IN 13V
    jack
    Reference Guide
    Guide de référence (au verso)
    Supplied accessories
    AC adaptor (AC-E1320D1) (1)
    AC power cord (1)
    Reference Guide (this document) (1)
    Design and specifications are subject to change without
    notice.
Sony SRS-BTV25

¿Necesita ayuda?

Número de preguntas: 1

¿Tiene alguna pregunta sobre Sony SRS-BTV25 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Sony SRS-BTV25 responder adecuadamente a su pregunta.

Antonio, 2019-12-01 13:07:57 Sin comentarios

Hay alguna manera de que no se apaguen al pasar un tiempo sin reproducir. Los tengo vinculados a google home y es molesto tener que encenderlos cada vez.

Responde a esta pregunta

Vea el manual de Sony SRS-BTV25 aquí, de forma gratuita. Este manual pertenece a la categoría Altavoces Dock y ha sido calificado por 1 personas con un promedio de 8.9. Este manual está disponible en los siguientes idiomas: Inglés, Francia. ¿Tiene alguna pregunta sobre Sony SRS-BTV25 o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Sony SRS-BTV25

General
Marca Sony
Modelo SRS-BTV25
Producto Altavoz Dock
EAN 4905524803709
Idioma Inglés, Francia
Tipo de archivo PDF
Altavoces
Ubicación de altavoz Portátil
Número de dispositivos -
Tweeter
Altavoz
Diámetro del tweeter 20mm
Diámetro del woofer 56mm
Canales de salida de audio 1.0canales
Tipo de altavoces -
Número de dispositivos -
Tweeter
Altavoz
Diámetro del tweeter 20mm
Diámetro del woofer 56mm
Canales de salida de audio 1.0canales
Tipo de altavoces -
Amplificador
Ampificador -
Audio
Potencia estimada RMS -W
Rango de frecuencia -Hz
Potencia estimada RMS -W
Rango de frecuencia -Hz
Otras características
Ecualizador
Tipo Altavoces portátiles
Potencia de altavoz 13W
Tipo Altavoces portátiles
Potencia de altavoz 13W
Desempeño
Control de volumen Digital
Material de la carcasa -
Color del producto Negro
Ampificador -
Ecualizador
Puertos e Interfaces
Tecnología de conectividad Inalámbrico
Tecnología de conectividad Inalámbrico
- USB
- Bluetooth
Peso y dimensiones
Ancho 145mm
Profundidad 145mm
Altura 145mm
Peso 500g
Ancho 145mm
Profundidad 145mm
Altura 145mm
Peso 500g
Control de energía
Alimentación USB
Voltaje de entrada AC 100 - 240V
Alimentación USB
Diseño
Control de volumen Digital
Material de la carcasa -
Color del producto Negro

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más