Vivanco UR 850 LCD

Vivanco UR 850 LCD manual

(1)
  • UR 850 LCD Universal Controller
    Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: hotline@vivanco.de 1
    (GB) Operating Instructions
    Vivanco UR 850 LCD remote control for
    practically all TV, audio, video and other
    infrared-controllable devices
    Inserting the batteries
    Open the battery compartment on the back of the
    device, push the flap down lightly and insert 2 AA
    alkaline batteries. Make sure that the polarity on the
    batteries and in the battery compartment correspond
    (thick spring = cell at bottom = -) and then close the
    lid carefully. – Use undamaged batteries only.
    Adapting to devices
    In order to control your devices you must adapt or
    set the remote control to them. There are two ways
    of doing so: direct control code entry or code
    search.
    If the UR 850 LCD does not understand you it
    displays ERROR and you can then repeat the entry.
    Direct control code entry
    Example: setting the remote control for a Philips TV
    set:
    1. Switch on your device, e.g. the TV, set to any
    station.
    2. To prepare code entry, briefly press the SET
    button in the bottom right corner of the keypad, then
    the required device button, e.g. TV. A brand and a
    code number appear, see diagram.
    – You cannot enter
    a new code if you have activated the code entry lock.
    3. Select the brand of your device, in this
    example Philips, with or . The first available
    code in the device list is displayed.
    4. Press a few buttons to determine whether you
    have found a suitable code. When the code
    corresponds to your device, press OK and the
    setting for this device is completed.
    5. If the code you have found does work at all or
    not properly, try another code by selecting the next
    code for the brand using the or button, then
    test the code as described above under 4. and, if
    successful, confirm with OK.
    6. To set the remote control for other devices,
    proceed in the same way. Instead of the TV device
    button, press another button, e.g. VCR, CBL/SAT
    (DVB-T, DECODER), DVD, TUNER, TAPE, CD,
    AUX).
    -Before setting a code and performing the subsequent test
    for recording or playback devices, please insert a medium
    (tape, CD, cassette, DVD, etc.).- You can interrupt code
    entry at any time by pressing EXIT.
    Code search
    If the brand of your appliance is not in the list or
    none of the codes given fits, we recommend the
    automatic code search.
    Your remote control finds the correct control settings
    almost automatically in a few seconds:
    1. Switch on the device to be controlled. For
    example, a program number appears in the display
    of your satellite receiver.
    2. To start the code search, press and hold the
    SET button for approx. 3 seconds. CODE SETUP
    appears in the display. Confirm this function by
    pressing OK.
    3. DEV SEARCH then appears in the display.
    Confirm this function by pressing OK.
    If DEV
    SEARCH does not appear you can set the function with the
    or button.
    4. Press the device button of the device to be
    controlled, e.g. DVD and confirm the function by
    pressing OK.
    5. Then point the remote control at the device to
    be controlled while the remote control emits a
    different ON/OFF signal every 2 seconds. The
    respective code number is shown in the display.
    6. When your device reacts, press a few buttons
    to determine whether you have found a suitable
    code. If the code corresponds to your device, press
    OK twice. SUCCESS appears in the display, then
    you press the device button, e.g. DVD, to confirm
    the entry. The setting for this device is now
    completed.
    7. If the code you have found does work at all or
    not properly, press EXIT and DEV SEARCH
    appears again. Then proceed again as described
    under 3.
    Please note: - You can reverse the search direction with the
    or button if you have reacted too slowly to a response
    from the device. – The Menu buttons cannot by used for
    testing. - Before setting a code and performing the
    subsequent test for recording or playback devices, please
    insert a medium (tape, CD, cassette, DVD, etc.).- You can
    interrupt code entry at any time by pressing EXIT.
    Other settings
    Setting the time
    1 Press and hold SET for 3 seconds, then set
    CONFIGURE with the or button. Confirm this
    function by pressing OK.
    2 TIME SETUP appears in the display. Confirm
    this function by pressing OK.
    3 Enter the time using the number buttons and
    confirm with the OK button. Then press EXIT
    several times to quit the setting mode.
    Set priority volume control
    With this function you can determine a device
    exclusively for volume control, e.g. your audio
    amplifier. Then the buttons VOL +, VOL and
    always control the amplifier, regardless of which
    device you are controlling.
    1 Press and hold SET for 3 seconds, then set
    CONFIGURE with the or button. Confirm this
    function by pressing OK
    2 TIME SETUP appears in the display. Set VOL
    LOCK with the or button. Confirm this function
    by pressing OK.
    3 Select the device button, e.g. AUX for the
    amplifier and set priority=ON using the or
    button. Confirm this function by pressing OK.
    4 Then press EXIT several times to quit the
    setting mode.
    - You can cancel the priority setting using the same
    procedure. Instead of ON, set OFF for all devices.
Vivanco UR 850 LCD

¿Necesita ayuda?

Número de preguntas: 0

¿Tiene alguna pregunta sobre Vivanco UR 850 LCD o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Vivanco UR 850 LCD responder adecuadamente a su pregunta.

Vea el manual de Vivanco UR 850 LCD aquí, de forma gratuita. Este manual pertenece a la categoría Mandos a distancia y ha sido calificado por 1 personas con un promedio de 9. Este manual está disponible en los siguientes idiomas: Español, Inglés, Alemán, Italiano. ¿Tiene alguna pregunta sobre Vivanco UR 850 LCD o necesita ayuda? Haz tu pregunta aquí

Especificaciones de Vivanco UR 850 LCD

General
Marca Vivanco
Modelo UR 850 LCD
Producto Mando a distancia
EAN 4008928188622
Idioma Español, Inglés, Alemán, Italiano
Tipo de archivo PDF
Exhibición
Pantalla LCD
Batería
Tipo de batería AAA
Numero de baterías soportadas 2
Contenido del embalaje
Pilas incluidas

Preguntas frecuentes

A continuación, encontrarás las preguntas más frecuentes sobre el Vivanco UR 850 LCD .

¿Tu pregunta no está en la lista? Haz tu pregunta aquí

ManualPDF.es

¿Busca un manual? ManualPDF.es asegura que encontrará el manual que está buscando en un abrir y cerrar de ojos. Nuestra base de datos contiene más de 1 millón de manuales en PDF de más de 10.000 marcas. Cada día añadimos los últimos manuales para que siempre encuentres el producto que buscas. Es muy sencillo: simplemente escriba el nombre de la marca y el tipo de producto en la barra de búsqueda y podrá ver instantáneamente el manual de su elección en línea de forma gratuita.

ManualPDF.es

© Copyright 2020 ManualPDF.es. Todos los derechos reservados.

Utilizamos cookies para asegurar que damos la mejor experiencia al usuario en nuestro sitio web. Si continúa utilizando este sitio asumiremos que está de acuerdo.

Leer más