1To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2Install this sound system in a well ventilated, cool, dry, clean
place-away from direct sunlight, heat sources, vibration, dust,
moisture, and/or cold. For proper ventilation, allow the
following minimum clearances.
Top : 10 cm (4 in)
Rear: 10 cm (4 in)
Side: 10 cm (4 in)
3Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5Avoid installing this unit where foreign object may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
–Other components, as they may cause damage and/or
discoloration on the surface of this unit.
–Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
–Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
6Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7Do not plug in this unit to a wall outlet until all connections
8Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9Do not use force on switches, knobs and/or cords.
10When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and
may cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage resulting
from use of this unit with a voltage other than specified.
13To prevent damage by lightning, keep the power cable
disconnected from a wall outlet or this unit during a lightning
14Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
16Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
17Before moving this unit, press p to set this unit to the
standby mode, and disconnect the AC power plug from the
18Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the
outlet, then leave this unit alone.
19When using this unit for a long time, this unit may become
warm. Turn the power off, then leave this unit alone for
20Install this unit near the AC outlet and where the AC power
plug can be reached easily.
21The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
Important notes for users in the U.K.
This apparatus is fitted with an approved 13 Amp plug. To change
a fuse in this type of plug proceed as follows:
1Remove fuse cover and fuse.
2Fix new fuse which should be a BS1362 5 Amp, A.S.T.
3Refit the fuse cover.
If the fitted plug is not suitable for your jack outlets, it
should be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of
5 Amp. If a plug without a fuse is used, the fuse at the
distribution board should not be greater than 5 Amp.
The severed plug must be disposed to avoid a possible
shock hazard should it be inserted into a 13 Amp jack elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code:
blue = neutral (N), brown = live (L).
As these colours may not correspond with the colour markings
identifying the terminals in your plug, proceed as follows:
–Connect the blue wire to the terminal marked N or coloured
–Connect the brown wire to the terminal marked L or
–Do not connect either wire to the earth terminal in the plug,
marked E (or e) or coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord
grip is clamped over the sheath of the lead - not simply over
the two wires.
Copyright in the U.K.
Recording and playback of material may require consent. See
Copyright Act 1956 and The Performer’s Protection Acts
1958 to 1972.
Caution: Read this before operating your unit.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off by p. This state is called the
standby mode. In this state, this unit is designed to
consume a very small quantity of power.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
The laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
Número de preguntas: 0
¿Tiene alguna pregunta sobre Yamaha BD-S473 o necesita ayuda? Haga su pregunta aquí. Proporcione una descripción clara y completa del problema y su pregunta. Cuantos más detalles proporcione para su problema y pregunta, más fácil será para otros propietarios de Yamaha BD-S473 responder adecuadamente a su pregunta.
Acerca de Yamaha BD-S473
Vea el manual de Yamaha BD-S473 aquí, de forma gratuita. Este manual pertenece a la categoría Reproductores Blu-ray y ha sido calificado por 1 personas con un promedio de 5.8. Este manual está disponible en los siguientes idiomas: Inglés. ¿Tiene alguna pregunta sobre Yamaha BD-S473 o necesita ayuda? Haz tu pregunta aquí